Dell PowerEdge systems 6300 Parts list manual

™

P/N 8398P February 1999

&

www.dell.com

5HSODFLQJ'HOO3RZHU(GJH

DQG6\VWHP3RZHU

6XSSOLHV

This document updates the power supply replacement procedure described in the

Installation and Troubleshooting Guides

for the PowerEdge 6300 and 4300 systems.

The new power supply uses an improved method of engaging and disengaging the

power supply into or out of the system chassis.

,QVHUWLQJWKH3RZHU6XSSO\

The following procedure assumes that you have already removed the existing power

supply from your chassis. See your

Installation and Troubleshooting Guide

for instruc-

tions on how to remove the existing power supply.

:$51,1*7RSUHYHQWWKHULVNRIERGLO\LQMXU\UHDGDOOVDIHW\LQVWUXFWLRQV

LQ\RXU,QVWDOODWLRQDQG7URXEOHVKRRWLQ

J

*XLGHEHIRUHUHPRYLQJRULQVHUW

LQJWKHSRZHUVXSSO\

To insert the new power supply, perform the following steps:

1. With the power supply handle in the open position, slide the power supply into

the chassis to the point where the power supply initially stops (see Figure 1).

)LJXUH,QVHUWLQJWKH3RZHU6XSSO\

2. Rotate the power supply handle to the closed position.

As you rotate the handle, pivot levers on the handle hinge engage into slots in the

chassis and push the power supply into the chassis. If the power supply does not

slide into the chassis, reposition the power supply and ensure that the power

supply handle is completely open before you try rotating the handle again.

3. With the power supply fully inserted into the chassis, push in on the handle until

the handle latches into place.

NOTE: The power supply will not function until the latch is engaged.

4. Connect the AC power cable to the power supply and route the cable through the

cable strain-relief clips on the power supply handle.

5. Connect the AC power cable to the power outlet.

power supply handle

(must be completely

open to insert the

power supply)

power supply

cable strain-

relief clips (3)

handle release latch

5HPRYLQJWKH3RZHU6XSSO\

To remove the power supply from your system, perform the following steps:

1. Disconnect the AC power cable from the power outlet and the power supply.

2. Remove the AC power cable from the cable strain-relief clips.

3. Press down on the handle release in the middle of the power supply handle,

rotate the handle to the open position, and pull the power supply out of the

chassis.

____________________

Information in this document is subject to change without notice.

© 1999 Dell Computer Corporation. All rights reserved. Printed in the U.S.A.

Trademarks used in this text:

Dell

, the

DELL

logo, and

PowerEdge

are trademarks of Dell Com-

puter Corporation. Other trademarks and trade names may be used in this document to refer to

either the entities claiming the marks and names or their products. Dell Computer Corporation

disclaims any proprietary interest in trademarks and trade names other than its own.

Other manuals for PowerEdge systems 6300

5

This manual suits for next models

1

Table of contents

Other Dell Server manuals

Popular Server manuals by other brands

HP

HP AlphaServer ES47 Cli reference manual

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

HP

HP ProLiant Gen9 user guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

HP

HP Integrity rx2600 overview

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Fujitsu

Fujitsu PRIMERGY BX900 quick start guide

Asus

Asus RS700DA-E6 PS4 user manual