Dell PowerEdge 2400 User manual



™









Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your

computer system.





  !"

"#

$%&$%&!"

"#

____________________

Information in this document is subject to change without notice.

Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell

Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any pro-

prietary interest in trademarks and trade names other than its own.

October 1999 P/N 6648R Rev. A01

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-1





 

! "#

To activate the integrated PowerEdge Expandable RAID Controller (PERC) 2/Si,

perform the following steps.



 !

"#$%&

'()*+,--.

+/01-+

%&+&,/.!

2&%&2+%

/01-!

3242+

/ 01-+++

#!5+-+565"

" !

1. Turn off and unplug your computer and peripherals.

2. Remove the right-side computer cover.

See “Checking Inside the Computer” in your system Installation and Trouble-

shooting Guide for more information.

3. Remove the cooling shroud.

See “Checking Inside the Computer” in your system Installation and Trouble-

shooting Guide for more information.

4. Press the ejectors on the RAID controller DIMM socket (see Figure 1-1) down

and outward to allow the dual in-line memory module (DIMM) to be inserted into

the socket (see Figure 1-2).

1-2 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si



1Integrated RAID hardware key connector (RAID_KEY)

2DIMM socket for optional RAID controller (DIMM_RAID)

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-3



5. Align the DIMM's edge connector with the slot in the center of the DIMM

socket, and insert the DIMM in the socket (see step A in Figure 1-2).

The DIMM socket has two alignment keys that allow the DIMM to be installed in

the socket in only one way.

NOTE: The RAID controller DIMM must be an unbuffered DIMM, rated to run at

100 MHz. Do not substitute registered DIMMs such as those used for system

memory. System memory is labeled “PC133.”

6. Press down on the DIMM with your thumbs while pulling up on the ejectors with

your index fingers to lock the DIMM into the socket (see step B in Figure 1-2).

7. Install the RAID hardware key in its socket on the system board (see Figure 1-1).

Secure the key with the latches on each end of the socket (see Figure 1-3). The

RAID hardware key should be labeled “PE2400.”

1DIMM socket ejectors (2)

2Alignment keys (2)

1-4 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si

 

8. Replace the cooling shroud and computer cover, and then reconnect the com-

puter and peripherals to their AC power sources and turn them on.

9. Press <F2> immediately after you see the following message:

<F2> = System Setup

If you wait too long and your operating system begins to load into memory, let

the system complete the load operation; then shut down the system and try

again.

For more information on the System Setup program, see “Using the System

Setup Program”in your system User’s Guide.

NOTE: To ensure an orderly system shutdown, consult the documentation that

accompanied your operating system.

10. Press <Alt> <p> to switch to Page 2 of the System Setup screen.

11. If the Onboard RAID option is displayed, select this option.

If the Primary SCSI option is displayed, the integrated RAID controller was not

detected; go to step 1 and repeat all installation steps.

'()*--+

/01-+%&/!

1RAID hardware key

2Latches (2)

3Socket

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-5

12. Press the left- or right-arrow key to set the Onboard RAID option to RAID.

The default setting for Onboard RAID is SCSI.

13. Press <Alt> <b> to save the settings and reboot the system.

14. Configure the RAID subsystem and install the RAID driver and management

software.

For more information, refer to the integrated PERC 2/Si controller documentation.

1-6 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si

Other manuals for PowerEdge 2400

This manual suits for next models

Table of contents

Other Dell Server manuals

Dell

Dell PowerEdge T420 Quick start guide

Dell

Dell PowerEdge M420 Operating manual

Dell

Dell PowerEdge 2650 User manual

Dell

Dell OptiPlex FX130 User manual

Dell

Dell Power Supply C8000 User manual

Dell

Dell D90D7 User manual

Dell

Dell PowerEdge C5125 User manual

Dell

Dell PowerEdge 6350 User manual

Dell

Dell PowerEdge R250 VN927 Manual

Dell

Dell PowerEdge M910 Quick start guide

Dell

Dell Wyse 5070 Extended User manual

Dell

Dell PowerEdge R730xd User manual

Dell

Dell PowerEdge 400SC Technical manual

Dell

Dell 3250 Technical manual

Dell

Dell PowerEdge 1655MC Manual

Dell

Dell 8 User manual

Dell

Dell PowerEdge 6350 User manual

Dell

Dell EMC PowerEdge R7515 User manual

Dell

Dell EMC PowerEdge R940 Manual

Dell

Dell PowerEdge System 840 MVT01 User manual

Dell

Dell Wyse ThinOS T10 User manual

Dell

Dell EMC PowerEdge R650xs Manual

Dell

Dell PowerVault NX200 User manual

Dell

Dell PowerEdge 2970 Technical manual

Popular Server manuals by other brands

HP AlphaServer ES47 Cli reference manual

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

HP ProLiant Gen9 user guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

HP Integrity rx2600 overview

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Fujitsu

Fujitsu PRIMERGY BX900 quick start guide

Asus

Asus RS700DA-E6 PS4 user manual