Dell Studio XPS User manual

Manuals
Documentation
Shop Services & Warranties
http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (1 of 37) [3/26/2008 3:57:09 PM]
Contact Us
Support Resource Center My Account
Technical Support Customer Service Warranty Information Dell Forums Contact Us
My Account My Preferences My Order Status My Systems & Peripherals Log Out 
You are here: Dell USA > Support Home Page
Back to Contents Page 
Removing and Installing Parts 
Dell™Dimension™XPS Service Manual
 Memory PCI Cards 
 AGP Cards Drives 
 Processor Airflow Shroud Processor 
 System Board Power Supply 
 Front Panel Drive Door 
 Battery 
 
Memory
You can increase your computer memory by installing memory modules on the system board. For information on the type 
of memory supported by your computer, see "Memory."
NOTE: DDR 333 memory operates at 320-MHz when used with an 800-MHz front-side bus 
processor. 
DDR Memory Overview 
DDR memory modules should be installed in pairs of matched memory size. This means that if you purchased your 
computer with 256 MB of memory installed and you want to add another 256 MB of memory, you must install it in 
the appropriate connector. If the DDR memory modules are not installed in matched pairs, the computer will continue 
to operate, but with a slight reduction in performance.
Hello, TIM (not TIM ?)
Cart
Keyword Search

Documentation

NOTE: Always install DDR memory modules in the order indicated on the system

board.

The recommended memory configurations are:

●A pair of matched memory modules installed in connectors DIMM1 and DIMM2

●A pair of matched memory modules installed in connectors DIMM1 and DIMM2 and another matched pair installed in

connectors DIMM3 and DIMM4

Additional memory recommendations include:

●Do not install ECC memory modules.

●Be sure to install a single memory module in DIMM 1 or the connector closest to the processor before you install

modules in the other connectors.

Memory Installation Guidelines

NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them

separate from any new modules that you may have, even if you purchased the new modules from Dell. You should

install your original memory modules in pairs either in connectors DIMM1 and DIMM2 or connectors DIMM3 and DIMM4.

If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not

function at optimal performance.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (2 of 37) [3/26/2008 3:57:09 PM]

Documentation

NOTE: Memory purchased from Dell is covered under your computer

warranty.

Installing Memory

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in your

Owner's Manual.

1. Follow the instructions in "Before You Begin."

2. Open the computer cover.

3. Lay the computer on its side so that the system board is on the bottom of the inside of the computer.

4. If necessary, remove a memory module:

a. Press out the securing clip at each end of the memory module connector.

b. Grasp the module and pull up.

If the module is difficult to remove, gently ease the module back and forth to remove it from the connector.

5. To insert a module, press out the securing clip at each end of the memory module connector.

6. Align the notch on the bottom of the module with the crossbar in the connector.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (3 of 37) [3/26/2008 3:57:09 PM]

Documentation

NOTICE: To avoid breaking the memory module, do not press near the middle of the

module.

7. Insert the module straight down into the connector, ensuring that it fits into the vertical guides at each end of the

connector. Press firmly on the ends of the module until it snaps into place.

If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.

8. Close the computer cover.

NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the

computer.

9. Connect your computer and devices to electrical outlets, and then turn them on.

10. Click the Start button, right-click My Computer, and then click Properties.

11. Click the General tab.

12. To verify that the memory is installed correctly, check the amount of memory (RAM) listed.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (4 of 37) [3/26/2008 3:57:09 PM]

Documentation

PCI Cards

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in your

Owner's Manual.

Your Dell™computer provides slots for up to four 32-bit, 33-MHz cards. For more information, see "Specifications."

NOTE: For optimum performance, install a PCI sound card only in PCI slot 3 or 4 and a modem card only in PCI slot 2,

3, or 4.

Installing a PCI Card

1. If you are replacing a card, remove the current driver for the card from the operating system.

2. Follow the instructions in "Before You Begin."

3. Open the computer cover.

4. Press the lever on the card retention arm and raise the retention arm.

5. If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 7.

6. If you are replacing a card that is already installed in the computer, remove the card.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (5 of 37) [3/26/2008 3:57:09 PM]

Documentation

If necessary, disconnect any cables connected to the card. Grasp the card by its top corners, and ease it out of its

connector.

7. Prepare the card for installation.

See the documentation that came with the card for information on configuring the card, making internal connections, or

otherwise customizing it for your computer.

CAUTION: Some network adapters automatically start the computer when they are connected to a

network. To guard against electrical shock, be sure to unplug your computer from its electrical outlet

before installing any cards.

8. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.

If the card is full-length, insert the end of the card into the card guide bracket as you lower the card toward its connector

on the system board. Insert the card firmly into the card connector on the system board.

9. Before you lower the retention arm, ensure that:

●The tops of all cards and filler brackets are flush with the alignment bar.

●The notch in the top of the card or filler bracket fits around the alignment guide.

10. Press the retention arm into place, securing the card(s) in the computer.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (6 of 37) [3/26/2008 3:57:09 PM]

Documentation

NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer

cover from closing properly or cause damage to the equipment.

11. Connect any cables that should be attached to the card.

See the documentation for the card for information about the card's cable connections.

12. Close the computer cover.

NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the

computer.

13. Connect your computer and devices to electrical outlets, and then turn them on.

14. Install any drivers required for the card as described in the card documentation.

Removing a PCI Card

1. Follow the instructions in "Before You Begin."

2. Open the computer cover.

3. Press the lever on the card retention arm and raise the retention arm.

4. If necessary, disconnect any cables connected to the card.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (7 of 37) [3/26/2008 3:57:09 PM]

Documentation

5. Grasp the card by its top corners, and ease it out of its connector.

6. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.

If you need a filler bracket, contact Dell.

NOTE: You must install filler brackets over empty card-slot openings to maintain FCC certification of the computer.

The brackets also keep dust and dirt out of your computer.

7. Lower the retention arm and press it into place, securing the card(s) in the computer.

8. Close the computer cover.

NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the

computer.

9. Connect your computer and devices to electrical outlets, and then turn them on.

10. Remove the card's driver from the operating system.

AGP Cards

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in your

Owner's Manual.

Your Dell™computer provides a connector for an AGP card.

Removing an AGP Card

1. Follow the instructions in "Before You Begin."

2. Open the computer cover.

3. Press the lever on the card retention arm and raise the retention arm.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (8 of 37) [3/26/2008 3:57:09 PM]

Documentation

4. Pull the card up and out of the card clip.

Installing an AGP Card

1. Follow the instructions in "Before You Begin."

2. Open the computer cover.

3. Press the lever on the card retention arm and raise the retention arm.

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (9 of 37) [3/26/2008 3:57:09 PM]

Documentation

4. Gently press the card into the AGP connector until it clicks into place, ensuring that the tab fits into the notch on the

front end of the card.

5. Lower the retention arm and press it into place, securing the card(s) in the computer.

6. Close the computer cover.

7. Connect the monitor cable to the card's video connector.

NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the

computer.

8. Connect your computer and devices to electrical outlets, and turn them on.

Drives

Overview

Your computer supports one floppy drive and a combination of up to four of the following:

●Either two IDE hard drives or two Serial ATA hard drives

●Two CD or DVD drives

http://support.dell.com/support/edocs/systems/dimxpsg2/en/SM/parts.htm (10 of 37) [3/26/2008 3:57:09 PM]

Other manuals for studio XPS

Table of contents

Other Dell Desktop manuals

Dell

Dell D32M User manual

Dell

Dell OptiPlex 580 User manual

Dell

Dell Alienware Aurora R3 User manual

Dell

Dell OptiPlex 7070 Operation and maintenance manual

Dell

Dell XPS 720 H2C User manual

Dell

Dell Inspiron 24 5421 User manual

Dell

Dell OptiPlex 38WYD User manual

Dell

Dell OPTIPLEX 740 User manual

Dell

Dell E521 - Dimension Motherboard UW457 0UW457 User instructions

Dell

Dell OptiPlex HUB User manual

Dell

Dell Studio XPS DCRM User manual

Dell

Dell XPS 630i User manual

Dell

Dell XPS 13 7390 Operation and maintenance manual

Dell

Dell XPS 730 Specification sheet

Dell

Dell PowerEdge 4200 Series User manual

Dell

Dell Vostro 3667 User manual

Dell

Dell Precision Rack 7910 User manual

Dell

Dell Inspiron 580 User manual

Dell

Dell Precision Workstation 350 User manual

Dell

Dell Vostro 400 User manual

Dell

Dell OptiPlex ARAIO User manual

Dell

Dell Precision 3450 Small Form Factor Cable Cover User manual

Dell

Dell Vostro 3681 User manual

Dell

Dell PowerEdge M820 Systems User manual

Popular Desktop manuals by other brands

HP m9060n - Pavilion - Elite Quick setup

Asus

Asus E210 Series user guide

TotalFlow

TotalFlow uFLO user manual

HP Presario SV7000 - Desktop PC manual

HP ProDesk 400 G5 Maintenance and service guide

Logitech

Logitech MK320 quick start guide

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

HP Z1 specification

Everex

Everex eXplora user manual

Lenovo

Lenovo ThinkCentre M75e user guide

Compaq

Compaq iPAQ Internet Device user guide

Dell studio XPS User manual

Popular Desktop manuals by other brands