Danfoss ERC 213 User manual
Installation Guide
ERC 213
Digital controller for refrigeration and defrost, 3 relays.
| 2 DKRCE.PI.RL0.G7.ML
Installation Guide | ERC 213
Dimensions (mm) and Mounting
83 66
Rear mounting (lock with clips)
Drilling template
Mounting Dismounting
61.2
28
D
36
71
29
| 3DKRCE.PI.RL0.G7.ML Installation Guide | ERC 213
Electrical Connections
DO1
12
SairS5Sc/DI
1D
I2
DO2 DO3
GN
DG
ND
3L 4N 567891011121
31
4
~~~~
Sair
Sc
DI1
DI2
DO2
DO3
DO1
S5
Power supply
(according to the product code number)
Connectors:
Max. Torque = 0.4 Nm
Quick programming tool: EKA 183B
| 4 DKRCE.PI.RL0.G7.ML
Installation Guide | ERC 213
ENGLISH
1 - Technical Highlights
yEase of use: Four buttons, easy menu structure, pre-installed application solutions ensure superior usability.
ySimple installation:
High Effect 16 A relay enable direct connection of heavy loads without use of intermediate relay: up to 2 hp
compressors depending on its power factor and motor efficiency (greater than 0.65 for 230 V and greater than 0.85
for 115 V).
A wide range of compatible types of sensors and screw connection terminals ensure highly flexible installation.
yUnit protection: Special software features like compressor protection from fluctuation in the power supply or from
high condensing temperature ensure the safe operation of the unit.
yEnergy efficiency: Defrost on demand, day/night mode and smart evaporator fan management ensure energy
efficiency.
The ERC 213 is a smart, multipurpose integrated refrigeration controller with temperature and defrost
management, available with 3 relays.
This controller is for Operating temperature sensing control, suitable for refrigeration and heating
applications.
Incorporated control has been designed to fulfil today’s requirements for commercial refrigeration
applications.
| 5DKRCE.PI.RL0.G7.ML Installation Guide | ERC 213
2 - User Interface
Press for one second: BACK
Press and hold: PULL-DOWN
Press for one second: UP
Press and hold: ON/OFF
Press for one second:
TEMPERATURE SETPOINT/OK
Press and hold: MENU
Press for one second: DOWN
Press and hold: DEFROST
Key Function
Press and hold at power up:
FACTORY RESET
(“FAC”is displayed)
Display Icons
Night mode
(Energy saving) Fan running Defrost
Compressor running
Flashes in pull-down mode Active alarm Unit (°C or °F)
ENGLISH
| 6 DKRCE.PI.RL0.G7.ML
Installation Guide | ERC 213
3 - Quick Configuration at Power Up
ySTEP 1: Power on
ySTEP 2: Select the quick configuration menu
Within 30 seconds of power on, press “<”BACK for 3 seconds.
The main switch“r12”is automatically set to OFF.
ySTEP 3: Select pre-installed application“o61”
The display automatically shows the application selection parameter“o61”.
Press SET to select the pre-installed application.
The display shows the default value (eg. “AP0”flashing).
Choose the application type by pressing UP/DOWN and press SET to confirm.
The controller presets parameter values according to the selected application and does not hide relevant parameters.
Tip: you can easily move from AP0 to AP6, and thus select the simplified list of parameters, by pressing the UP key
(circular list).
App Description
App 0 None (no preset application)
App 1Medium temperature ventilated refrigeration units (2 – 6 °C), with timed natural defrost
App 2Medium temperature ventilated refrigeration units (0 – 4 °C), with timed electrical defrost
App 3Low temperature ventilated refrigeration units (-26 – -20 °C), with timed electrical defrost
App 4Medium temperature ventilated refrigeration units (0 – 4 °C), with electrical defrost (by temperature)
App 5Low temperature ventilated refrigeration units (-26 – -20 °C), with electrical defrost (by temperature)
App 6 None (no preset application) with simplified parameter list
ENGLISH
| 7DKRCE.PI.RL0.G7.ML Installation Guide | ERC 213
Quick Configuration at Power Up
ySTEP 4: Select sensor type“o06”
The display automatically shows sensor selection parameter“o06”.
Press SET to select the sensor type.
The display shows the default value (eg. “n10” flashing).
Choose sensor type by pressing UP/DOWN (n5=NTC 5 K, n10=NTC 10 K, Ptc=PTC, Pt1=Pt1000) and press SET to
confirm.
NOTE: All sensors must be the same type.
ENGLISH
| 8 DKRCE.PI.RL0.G7.ML
Installation Guide | ERC 213
4 - Menu structure
1) Parameter groups
2) Parameter name
Scroll through the
parameter groups
SET: press for 3 seconds to access
status, setup and service
Password (if enabled)
Status input
Configuration
Main switch
Application
Sensor type
SET
Scroll through the
parameter names
SET
3) Value
Application 0
Application
6-5-4-3-2-1
Application
1-2-3-4-5-6
ENGLISH
| 9DKRCE.PI.RL0.G7.ML Installation Guide | ERC 213
5 - Quick Configuration via “cFg” Menu
yPress SET for three seconds to access the parameters groups.
ySelect “CFg” menu and press SET to enter. The first menu“r12”(main switch) is displayed.
ySwitch OFF main switch (r12=0) for changing the pre-installed application.
yPress UP/DOWN to scroll through the parameter list.
yConfigure the “o61”parameter to select a pre-installed application
- Press SET to access the“o61”parameter.
- Press UP/DOWN to select an application (AP0= no application selected).
- Press SET to confirm, “o61” is displayed.
yContinue to set the next parameters (“o06”sensor type) in the “cFg” menu.
ENGLISH
| 10 DKRCE.PI.RL0.G7.ML
Installation Guide | ERC 213
6 - Basic operation
Initiate a manual defrost
Adjust the setpoint temperature
DEFROST: press for 3 seconds to initiate a defsost.
The DEFROST icon is shown during defrost.
DEFROST: press for 3 seconds to stop manual defrost.
(short press) SET: adjust setpoint temperature.
UP/DOWN: change the temperature setpoint
(in setting mode the setpoint flashes).
SET: save the temperature setpoint.
ENGLISH
Other manuals for ERC 213
3
Table of contents
Languages:
Other Danfoss Controllers manuals
Danfoss
Danfoss VLT Option Panel User manual
Danfoss
Danfoss Optyma Plus OP-MPS User manual
Danfoss
Danfoss AME 655 User manual
Danfoss
Danfoss ECL Comfort 210 Installation instructions manual
Danfoss
Danfoss AMI 140 User manual
Danfoss
Danfoss AMV 655 User manual
Danfoss
Danfoss ECL Comfort C31 User manual
Danfoss
Danfoss AME 435 QM User manual
Danfoss
Danfoss EKC 201 User manual
Danfoss
Danfoss AK-PC 572 User manual
Danfoss
Danfoss PK37 User manual
Danfoss
Danfoss VLT 6000 series User manual
Danfoss
Danfoss EKD 316C Colibri User manual
Danfoss
Danfoss NovoCon Series User manual
Danfoss
Danfoss VLT HVAC Basic Drive FC 101 User manual
Danfoss
Danfoss VLT FC 100 User manual
Danfoss
Danfoss EKC 202A User manual
Danfoss
Danfoss pved-cl User manual
Danfoss
Danfoss ACCSCS User manual
Danfoss
Danfoss EKC 313 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
