Da-Lite Cosmopolitan Electrol User manual

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 13

Warsaw, Indiana 46581-013

Phone: 5 4-26 -8101

800-622-3 3

Fax: 5 4-26 - 804

www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Boo for

COSMOPOLITAN®ELECTROL®

12'x12', 200" Diagonal and Larger Sizes

Carefully unpack screen an remove outer wrapping from case.

Remove the black tape an rubber ban s from the slat bar after the

case has been installe .

The Cosmopolitan®Electrol®comes with brackets to allow for wall

mount or ceiling mount installations. Proce ures for each metho

are as follows:

Wall Mount

1. The wall mount bracket shoul be fastene to wall stu s or

some reinforcement within the wall. Concrete or brick walls

require special fasteners an anchors.

2. The wall bracket has holes space at 16" an 24" to align with

most wall stu s.

3. The bracket must be level an plumb.

4. Keep in min you will nee at least 2-3/4" between the ceiling

an the top of the wall mount bracket to be able to position

the case on the bracket.

5. Mount the screen case on the wall bracket as shown in

figure 1. Be sure the case is fully seate on the bracket.

Tighten the stop screws against the wall bracket.

Ceiling Mount

1. Be sure the ceiling has a equate reinforcement to attach the

screen brackets.

2. Attach the ceiling brackets to the wall mount bracket using

the supplie 5/16" x 3/4" bolts, washers an nuts.

3. Position the ceiling bracket asssembly on the ceiling an

attach with 5/16" bolts (not supplie ). The bolts shoul be

long enough to pass through the rywall or ceiling tile an

penetrate at least 1-1/2" into the reinforcement in the ceiling.

4. Mount the screen on the wall bracket as shown in figure 2.

Be sure the case is fully seate on the bracket. Tighten the

stop screws against the wall bracket.

INSTALLATION

CASE HOOK

VIEWING SURFACE

(AUDIENCE SIDE)

FIGURE 2

FIGURE 1

VIEWING SURFACE

(AUDIENCE SIDE)

CASE HOOK

WALL

MOUNT

BRACKET

STOP SCREW

CEILING

MOUNT

BRACKET

5/16x3/4"

BOLT, NUT

AND LOCK

WASHER

WALL MOUNT

BRACKET

STOP SCREW

1-1/8"

IMPORTANT SAFETY INSTRUCTIONS

When using your vi eo equipment, basic safety precautions shoul always be followe , inclu ing the following:

1. Rea an un erstan all instructions before using.

2. Position the cor so that it will not be trippe over, pulle , or contact hot surfaces.

3. If an extension cor is necessary, a cor with a current rating at least equal to that of the appliance shoul be use .

Cor s rate for less amperage than the appliance may overheat.

4. To re uce the risk of electric shock, o not isassemble this appliance. Contact an authorize service ealer when

repair work is require . Incorrect reassembly can cause electric shock when the appliance is use subsequently.

5. The use of an accessory attachment not recommen e by the manufacturer may cause a risk of fire, electric shock,

or injury to persons.

SAVE THESE INSTRUCTIONS

COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITHOUT A BUILT-IN LOW VOLTAGE CONTROL

Internal wiring has been complete at the factory. Installer must route power to the wall switch an to the junction box

locate on the left en of the screen case.

See wiring iagram below for wire connections.

NOTE: This screen can only be controlled by a single 120VAC or 240VAC wall switch. To use multiple switches, an optional low

voltage control must be used.

OFF

DOWN

THIS SWITCH CAN NOT

BE USED WITH LVC.

120V WIRING DIAGRAM

FOR STANDARD

WALL SWITCH

SPDT SWITCH WITH

CENTER OFF AC (COMMON)

AC HOT 120VAC 60HZ 1 AMP

BLACK/YELLOW

BLACK

RED

WHITE

BLACK (DOWN)

RED (UP)

JUNCTION BOX

LOCATED IN LEFT

ENDCAP

WHITE

BLACK

RED

GREEN

MOTOR

NOTE: A SINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN

ONE SCREEN. CONTACT THE FACTORY FOR FURTHER

INFORMATION.

Screen travel is stoppe automatically in the own an up positions by the limit switches that are preset at the factory.

No further a justment is necessary.

If you nee to make minor stop position a justments see the appropriate step below.

SETTING THE DOWN LIMIT POSITION

NOTE: One turn of the limit screw equals approximately 2" of screen travel.

TO REDUCE SCREEN DROP:

Turn the own limit switch screw clockwise to ecrease the

amount of screen rop. Run the screen own to test the stop

position. If the screen rops too far, raise the screen about one foot

an a just the limit switch again. Repeat until the esire position

is set.

TO INCREASE SCREEN DROP:

Turn the own limit switch screw counterclockwise to increase the amount of screen rop. Run the screen own

to test the stop position. If the screen oes not rop enough, raise the screen about one foot an a just the limit

switch again. Repeat until the esire position is set. Do not a just for more rop than what was or ere . At least

1-1/2 wraps of fabric must remain on the roller.

SCREEN ADJUSTMENT FOR SCREENS WITHOUT A BUILT-IN LOW VOLTAGE CONTROL

UP LIMIT SWITCH ACCESS

THROUGH CASE OPENING

FIGURE 3

DOWN LIMIT

SWITCH

ACCESS HOLE

240 VOLT WIRING DIAGRAM

FOR STANDARD WALL SWITCH:

Da-Lite offers two styles of 240 volt

wall switches for stan ar operation.

Please see wiring iagram inclu e in

wall switch box inclu e with screen.

SETTING THE UP LIMIT POSITION

CAUTION: Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case. The

screen could be damaged.

SCREEN TRAVELS INTO CASE TOO FAR:

Turn the up limit switch screw clockwise to ecrease the amount of travel. Run the screen up to test the

stop position. If the screen oes not stop properly, lower the screen about one foot an turn the limit

switch again. Repeat until the esire position is set.

SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE:

Turn the up limit switch screw counterclockwise to increase the amount of up travel. Run the screen up to

test the stop position. If more travel is esire , lower the screen about one foot an a just the limit switch

again. Repeat until the esire position is set.

SCREEN ADJUSTMENT FOR SCREENS WITHOUT A BUILT-IN LOW VOLTAGE CONTROL

▲

COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITH A BUILT-IN LOW VOLTAGE

CONTROL

LOW-VOLTAGE WALL SWITCH

OPTIONAL IR AND RF

REMOTE CONTROL

MOTOR

WHITE (COMMON)

BLACK (HOT)

GREEN

GROUND TO CASE

120VAC 60HZ

120V WIRING DIAGRAM

WITH OPTIONAL BUILT-IN

LOW VOLTAGE CONTROL

SPLITTER

RJ9

STOP

DOWN

GROUND MUST BE

CONNECTED TO

BUILDING GROUND

RJ9

GREEN

FRONT BACK

UP DN GND +5V

3-POSITION

SWITCH RJ9

ILT RJ9PIN-OUTS

(TAB IS FACING UP)

IR or UP BLACK

GND COMMON RED

+5V GREEN

DN or DATA WHITE

+5V

COM

DRY CONTACTS

FIGURE 4

IMPORTANT NOTE: The wall switch is REQUIRED to make any limit

switch a justments, EVEN if a thir party control

system is use . Therefore, it is a vise to wire

the switch or provi e a 4-con uctor connection

that is accessible.

LOW-VOLTAGE WALL SWITCH

OPTIONAL IR AND RF

REMOTE CONTROL

MOTOR

BLUE (COMMON)

BROWN (HOT)

GREEN

GROUND TO CASE

240VAC 50HZ

240V WIRING DIAGRAM

WITH OPTIONAL BUILT-IN

LOW VOLTAGE CONTROL

RJ9

STOP

DOWN

GROUND MUST BE

CONNECTED TO

BUILDING GROUND

RJ9

GREEN

FRONT BACK

UP DN GND +5V

3-POSITION

SWITCH RJ9

ILT RJ9PIN-OUTS

(TAB IS FACING UP)

IR or UP BLACK

GND COMMON RED

+5V GREEN

DN or DATA WHITE

DRY CONTACTS

SPLITTER

+5V

COM

COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITH A BUILT-IN LOW VOLTAGE

CONTROL

FIGURE 5

SCREEN ADJUSTMENT FOR SCREENS WITH A BUILT-IN LOW VOLTAGE CONTROL

1. Remove the cover plate from the 3-button wall switch an remove the switch from the junction box.

2. Locate small 3-position switch on back of wall switch. See Figure 4 for 120V screens or Figure 5 for

220/240V screens.

3. To a just the own limit switch, sli e the 3-position switch to the own position. Press an hol the own

button to run the screen own to the esire stop position. Release the button to stop the screen. DO

NOT PUSH THE STOP BUTTON.

4. When the screen is in the esire own position, sli e the 3-position switch to the off (center) position.

The own limit switch is now set.

5. To a just the up limit switch, sli e the 3-position switch to the up position. Press an hol the up button

to run the screen up to the esire stop position. Release the button to stop the screen. DO NOT PUSH

THE STOP BUTTON.

6. When the screen is in the esire up position, sli e the 3-position switch to the off (center) position. The

up limit switch is now set.

7. To test limit switch setting, make sure the 3-position switch is in the off (center) position. Press an

release the up or own button on the wall switch to operate the screen.

8. Replace switch an cover plate on the wall.

NOTE: If stop button is presse , the wall switch will reverse irection. To correct this, press the stop button

again. This will reset the switch. You will have to re-set both the up an the own settings.

IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch a justments, EVEN if a thir party

control system is use . Therefore, it is a vise to wire the switch or provi e a 4-con uctor

connection that is accessible.

IMPORTANT NOTE: The wall switch is REQUIRED to make any limit

switch a justments, EVEN if a thir party control

system is use . Therefore, it is a vise to wire

the switch or provi e a 4-con uctor connection

that is accessible.

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate.

Motor oes not hum.

2. Incorrect stopping position in

downward irection.

3. Incorrect stopping position in

upward irection.

4. Noise.

NOTE: Screen will operate with a

low pitched hum.

5. Coasting.

CAUSE

(a) Blown fuse.

(b) Trippe circuit breaker.

or junction.

Power at junction box

( ) Thermal overloa trippe .

(e) Broken wire in the “down” or “up”

position.

(f) Defective motor, limit switch or

capacitor.

(g) Capacitor burne out.

(a) Lost roller wrap.

(b) “Down” limit switch out of

a justment

(a) Lost roller wrap.

(b) “Up” limit switch out of

a justment

(a) Gear Noise.

(a) Defective brake.

RESTORING LOST ROLLER WRAP

1. Tape a strap to the bottom of the

screen surface.

2. Push strap over back of roller.

3. Fee fabric as you pull strap to

raw fabric over top of roller.

4. Remove tape an strap.

SOLUTION

(a) Replace fuse.

(b) Reset circuit breaker.

wire connections. Correct any

improper connections.

“Down” Position

Check for power across black

an white lea s.

“Up” Position

Check for power across re

an white lea s.

( ) Let motor cool own for 15

minutes. Try again.

(e) Check for continuity. Cut off ol

splice an reconnect.

(f) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(g) Replace motor assembly.

(a) See instructions below.

(b) See installation instructions.

(a) See instructions below.

(b) A just “up” limit switch. See

installation instructions

(a) Replace motor assembly.

Printed in U.S.A. 96652 Rev. 7/09

Other manuals for Cosmopolitan Electrol

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite ACOUSTICAL IMAGER User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite DESIGNER DA-TAB ELECTROL User manual

Da-Lite

Da-Lite Designer Da-Tab Electrol User manual

Da-Lite

Da-Lite Parallax Thin User manual

Da-Lite

Da-Lite Picture King User manual

Da-Lite

Da-Lite TENSIONED PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Designer Electrol User manual

Da-Lite

Da-Lite DescenderPro User manual

Da-Lite

Da-Lite Da-Snap Screen User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Large advantage electrol User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite Contour Electrol User manual

Da-Lite

Da-Lite DELUXE MODEL B User manual

Da-Lite

Da-Lite FullVision User manual

Da-Lite

Da-Lite C User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Polacoat Flex Plex User manual

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite IDEA Screen User manual

Da-Lite

Da-Lite CINEMA CONTOUR SCREEN User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions