CYP CPLUS-V4H2HP User manual
CPLUS-V4H2HP
6G UHD 4 to 2 HDMI Matrix with HDCP2.2
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2016 by Cypress Technology.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
RDV1 29/06/16 Preliminary Release
CONTENTS
1. Introduction................................................................1
2. Applications...............................................................1
3. Package Contents ....................................................1
4. System Requirements................................................1
5. Features......................................................................2
6. Operation Controls and Functions...........................3
6.1 Front Panel ............................................................3
6.2 Rear Panel.............................................................4
6.3 WebGUI.................................................................5
6.3.1 WebGUI Control Page......................................6
6.3.2 Power On/Off ....................................................6
6.3.3 Routing ...............................................................7
6.3.4 Source Detect ..................................................7
6.3.5 Status ..................................................................8
6.3.6 EDID ....................................................................8
6.3.7 HDCP Control ....................................................9
6.3.8 Firmware Update ............................................10
6.3.9 HDMI Out A Info & HDMI Out B Info ..............10
6.3.10 NAMING .........................................................11
6.3.11 Network Setting .............................................11
6.4 Telnet Control ....................................................12
6.5 RS-232 Command ..............................................14
6.6 IR Cable Pin Assignment....................................16
6.7 D-sub 9 Pin Denition .......................................16
7. Connection Diagram ..............................................17
8. Specications ..........................................................18
9. Support Timing Table & HDMI Cable Length .........19
9.1 Support Timing Table .........................................19
9.2 HDMI Cable Length ...........................................20
10 Remote Control.......................................................20
1
1. INTRODUCTION
This 6G UHD 4 by 2 HDMI Matrix allows customer to route up to
four 6G HDMI input signals to any of two 6G HDMI outputs. This unit
supports 4K@60Hz (YUV 4:4:4), 48-bit Deep Color, HDR (High Dynamic
Range), HD audio formats and other features dened by the HDMI
2.0 specication. Five pre-dened internal EDIDs and two external
EDID selections are available for EDID management. The unit provides
intuitive front panel controls as well as RS-232, telnet, WebGUI and IR
remote control options.
2. APPLICATIONS
• Entertainment Room & Home Theater
• Show Room & Demo Room
• Lecture Room & Hall Presentation
• Show Room & Demo Room
• Public Commercial Display
3. PACKAGE CONTENTS
• 1 x HDMI matrix unit
• 1 x IR Extender with cable
• 1 x 5V / 2.6A DC power adaptor
• 1 x Remote control unit (model: CR-155)
• 1 x Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as media players, video game consoles
or set-top boxes and HDMI receiving equipment such as HDTVs,
monitors or audio amplier
2
5. FEATURES
• HDMI 2.0, HDCP 2.2 and DVI 1.0 compliant
• Supports matrix routing of four 6G HDMI inputs to two 6G HDMI
outputs
• Supports HDTV resolutions up to 4K UHD (3840x2160@24/25/30/50/60
& 4096x2160@24/25/30/50/60Hz)
• Maximum data rate up to 6Gbps with Deep Color support up to
1080p 48-bit
• Supports pass-through of HD audio formats including LPCM 2.0~7.1,
Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos
and DTS-HD Master Audio
• Supports EDID management via ve pre-dened internal EDIDs and
two external EDID selections
• Multiple control interfaces including RS-232, telnet, WebGUI and IR
remote
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWERA
A
1
2
3
4
1
2
3
4
B
BH
DMI IN
2.2
+
HDMI IN / OUT
1
1 2 3 4 5 6
1IR window: Accepts IR signals from the included IR remote for
control of this unit only.
2POWER: Press this button to power on the unit or place it into stand-
by mode.
Note: Ethernet and RS-232 remain active while the unit is in stand-
by mode.
3Power indicator: The LED will illuminate RED to indicate the unit is
receiving power but is in stand-by mode. It will illuminate GREEN to
indicate that the unit has been turned on.
4HDMI out indicator “A & B”: The correspondence LED will illuminate
GREEN when a stable connection with an output device is
detected.
5HDMI In indicator “1&2&3&4”: The correspondence LED will
illuminate GREEN when a stable connection with an input device is
detected.
6HDMI In: Connect to HDMI source equipment such as a media
player, game console or set-top box. DVI source equipment may
be connected by using an HDMI to DVI adapter.
4
6.2 Rear Panel
234AB
HDMI IN HDMI OUT SERVICECONTROL RS-232 IR IN DC 5V
1 2 3 4 5 6 7
1HDMI In : Connect to HDMI source equipment such as a media
player, game console or set-top box. DVI source equipment may
be connected by using an HDMI to DVI adapter.
2HDMI Out: Connect to HDMI TVs, monitors or ampliers for
digital video and audio output. DVI display equipment may be
connected by using ans HDMI to DVI adapter.
3SERVICE: This slot (USB 2.0) is reserved for rmware update use only.
Please plug in a USB thumb drive containing the new rmware to
update the unit.
4CONTROL: Connect directly, or through a network switch, to your
PC/laptop to control the unit via telnet/WebGUI.
5RS-232: Connect directly to your PC/laptop to send RS-232
commands to control the unit.
6IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
7DC 5V: Plug the 5V DC power adapter into the unit and connect
it to an AC wall outlet for power. The LED will illuminate GREEN to
indicate the unit is on and receiving power.
5
6.3 WebGUI
Install the IP Discovery Tool:
1. Please obtain the Device Discovery software from your authorized
dealer and save it in a directory where you can easily nd it.
Note: The unit’s default IP address is 192.168.1.50
2. Connect the unit and your PC/Laptop to the same active network
and execute the Device Discovery software. Click on “Find
Devices on Network” and a list of devices connected to the local
network will show up indicating their current IP address.
3. By clicking on one of the listed devices you will be presented with
the network details of that particular device. If you choose, you
can alter the static IP network settings for the device, or switch
the unit into DHCP mode to automatically obtain proper network
settings from a local DHCP server. To switch to DHCP mode,
please select DHCP from the IP mode drop-down, then click
“Save” followed by “Reboot”.
Table of contents
Other CYP Matrix Switcher manuals
