Cross Technologies 2415-x02 User manual

Instruction Manual

Model 2415-x02

Multi Channel Upconverter

2415-402 Four Channel • 2415-302 Three Channel • 2415-202 Two Channel • 2415-102 One Channel

August 2015, Rev. D

EXECUTE

MODEL 2415

CROSS TECHNOLOGIES INC.

UPCONVERTER

REMOTE POWER

ALARMS

1674.125 1926.250

1926.375 2086.625

------ CH 1 -------- ------ CH 2 --------

1234

------ CH 3 -------- ------ CH 4 --------

(Shown, Model 2415-402 - Four Channel, Front Panel)

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,

equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

Model 2415-x02 Multi Channel Upconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Specifications 4

1.3 Monitor & Control Interface 6

1.4 Environmental Use Information 10

2.0 Installation 11

2.1 Mechanical 11

2.2 Rear Panel Inputs & Outputs 12

2.3 Front Panel Controls & Indicators 13

2.4 Operation 14

2.5 Menu Settings 17

3.0 Ethernet Interface 18

3.1 Connection 18

3.2 Ethernet Configuration 18

3.3 Webpage M&C 21

3.4 SNMP Configuration 22

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

WEB www.crosstechnologies.com

E-MAIL [email protected]

2415-x02 Manual, Rev. E Page 2 09/28/17

Model 2415-x02

Multi Channel Upconverter

2415-402 Four Channel • 2415-302 Three Channel • 2415-202 Two Channel • 2415-102 One Channel

1.0 General

1.1 Equipment Description

The 2415-402 Upconverter has four individual channels, each one converts 70 MHz to 950 to 2150 MHz in 125

kHz steps using PLL in “exact frequency mode” with low group delay and flat frequency response. Synthesized

local oscillators (LO) provide frequency selection. Push button switches select the output frequency, gain, and

other parameters. Front panel LEDs provide indication of DC power, PLL alarm or Remote operation. Gain is

adjustable manually over a 0 to +30 dB range in 0.5 ± 0.5 dB steps. The frequency and gain of each channel are

also remotely selectable. Parameter selection and frequency and gain settings appear on the LCD display.

Connectors are Type F female for the RF, and BNC female for the IF andexternal 10 MHz reference input and

output. The10 MHz reference can be inserted on all RF lines. The table below shows available options.SSPB

+24 VDC option V1, can be inserted only on the channel 1 RF line.The 2415-402 is powered by a 100-240

±10% VAC, 47-63 Hz power supply, and is contained in a 1 3/4” X 19” X 16” rack mount chassis.

* 2415-x02, Four (4) Channels, 2415-302, Three (3) Channels, 2415-202, Two (2) Channels, 2415-102, One (1) Channel.

EXECUTE

MODEL 2415

CROSS TECHNOLOGIES INC.

UPCONVERTER

REMOTE POWER

ALARMS

1674.125 1926.250

1926.375 2086.625

------ CH 1 -------- ------ CH 2 --------

1234

------ CH 3 -------- ------ CH 4 --------

FRONT PANEL (2415-402 - Four Channel show)

PSA

GND

J11 J12

AND

MONITOR

CONTROL

CHANNEL 4

RF OUT

J10

IF IN

CHANNEL 3

RF OUT

IF IN

CHANNEL 1

RF OUT

VDC

IF IN 10 MHZ REF

OUTPUT

10 MHZ IN/OUT

10 MHZ REF

INPUT

CHANNEL 2

RF OUT

IF IN

PSB

234 6

789

REAR PANEL (2415-402 - Four Channel shown with optional Ethernet)

FIGURE 1.1 Model 2415-x02 Front and Rear Panels

SW,PLL,ATT,

10M CONTROL

M&C

CONTROLLER

EXT

10MHz

INT 10MHz

10MHz

VCOs

2415-402

Block

Diagram

0.8 to 2.2 HP/LP2400 MHz BP

3.35 to

4.55 GHz

var

atten

MHz

2470

MHz

200 MHz LP 0.95

2.15

GHz

OUT

SAME FOR FREQUENCY CHANNEL 2

SAME FOR FREQUENCY CHANNEL 3

SAME FOR FREQUENCY CHANNEL 4

10 MHz, std.,

DC - O

t V1

var

atten

------ CH 1 -------- ------ CH 2 --------

------ CH 3 -------- ------ CH 4 --------

1674.125 1926.250

1926.375 2086.625

FIGURE 1.2 Model 2415-x02 Upconverter Block Diagram

(Block Diagram applies to Models 2415-102, 202, 302 & 402)

2415-x02 Manual, Rev. E Page 3 09/28/17

<-60 dB t

ical

<-50 dB min.

;

G=30

-30 dBm in

ut levelChannel to Channel Isolation

-35 to -10 dBmInput Level Ran

Input Characteristics

Out

ut Characteristics

Channel Characteristics

Synthesizer Characteristics

> 50 dB

minimumIma

e Re

ection

-20 to 0 dBmOut

ut Level Ran

TABLE 1.0 2415-x02 Multi-Channel U

converter Technical S

ecifications**

125 kHz

(

as low as 1 kHz ste

s available

)

Fre

uenc

Ste

±1.0

m max. over tem

(

±0.01

tion H

)

Fre

uenc

Accurac

Non-invertin

Fre

uenc

Sense 0.015 ns/MHz2

arabolic

;

0.05 ns/MHz linear

;

1 ns ri

leGrou

Dela

max.

< -50 dBc

in bandS

urious Res

onse

±1.5 dB

950 - 2150 MHz

;

±0.5 dB

36 MHz BW

;

±1.0 dB

40 MHz BWFre

uenc

Res

onse

0 to +30.0 dB in 0.5 ±0.5 dB ste

sGain Ran

(

ustable

)

+10 dBm

maximum

ainOut

ut 1 dB com

ression

950 to 2150 MHzFre

uenc

75Ω/ 12 dB (See Table 2.2 for connector options)

edance/Return Loss

70 ±18 MHzFre

uenc

75Ω/18 dB

(

See Table 2.2 for connector o

tions

)

edance/Return Loss

-97 -117

-90 -110-80

-70-65

-60Standard 125 kHz ste

s dBc/Hz -83-77-69-67

100k 1M10k1k10010

ical: dBC/Hz

Phase Noise @ Fre

(

)

19 inch

1RU standard chassis

1.75” hi

h x 16.0” dee

Size

Controls

Indicators

Other

75ΩBNC

(

female

75ΩBNC

(

female

)

works with 50Ω& 75ΩIF

10 MHz Connectors

Direct readout LCD

;

manual or remote selectionGain Selection

3 dBm

± 3 dB

75 ohms

(

tion -E

)

10 MHz Level

(

In or Out

)

100-240 ±10% VAC

47- 63 Hz

45 watts maximumPower

RS232/RS485 selectable

Ethernet o

tional

)

Remote

Direct readout LCD

;

manual or remote selectionFre

uenc

Selection

DB9

(

female

)

- NO or NC contact closure on AlarmAlarm

Remote Connector

e F

(

female

)

See table 2.2 for other o

tionsRF Connector

Green LED

;

Red LED

;

Yellow LEDPower

;

Alarm

;

Remote

(Technical Specifications continued on page 5...)

2415-x02 Manual, Rev. E Page 4 09/28/17

(Technical Specifications continued from page 4...)

140 ±36/70 ±18 MHz SelectableW140/70-x

Ethernet with Web BrowserW8 -

Redundant Power Su

R -

h Stabilit

(

±0.01

)

internal ref.H -

1 kHz Fre

uenc

Ste

SizeX1002 - x

Ethernet with TCP/IP

Telnet®W28 -

SSPB DC

CH1

(

ONLY

+24VDC

2.5 AV1 -

Available O

tions

140 ±36 MHzW140-x

Ethernet with Web Browser & SNMPW18 -

See TABLE 2.2Connectors/Im

edance

**+10˚C to +40˚C; S

ecifications sub

ect to chan

e without notice Cross Technolo

ies, Inc. 2015

Channel Model Numbers:

Model 2415-402 - (4) Channels

Model 2415-302 - (3) Channels

Model 2415-202 - (2) Channels

Model 2415-102 - (1) Channel

x = Number of Channels

2415-x02 Manual, Rev. E Page 5 09/28/17

1.3 Monitor and Control Interface

A) Remote serial interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

(RS-232C, RS-422, or RS-485)

Female DB-9

PC Com Port Male DB-9

2415-x02 M&C Port

M&C Cable Diagram - Cross Technologies Frequency Converters

RX RX

TX TX

DTR

DSR

RTS

CTS

Connector: Rear panel, DB-9 female

J10 Pinouts

(RS-232C/422/485)

Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

2415-x02 Manual, Rev. E Page 6 09/28/17

B) Status Requests

Table 1.1 lists the status requests for the 2415-x02 and briefly describes them.

PLEASE NOTE:

Status requests of values specific to a channel

must be preceded by a *i where *i is the channel number.

PLEASE NOTE:

The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485 is selected.

TABLE 1.1 2415-x02 Statu

s Requests

Status Requests

TABLE 1.1 2415-x02 Status Requests

Command Syntax* Description

Get channel frequency {aa*iSF} Returns {*iSFxxxxxxx} where :

• i = 1, 2, 3 or 4 designating the channel number

• xxxxxxx = frequency in KHz

Get channel gain {aa*iSG} Returns {*iSGxxx} where:

• i = 1, 2, 3 or 4 designating the channel number

• xxx = gain to nearest 1.0 dB (e.g., +14 = 14 dB)

Get mute setting {aa*iSM} Returns {*iSMx} where :

• i = 1, 2, 3, or 4 designating the channel number

• x = 1 for Mute ON (carrier OFF)

• x = 0 for Mute OFF (carrier ON)

Get setting for reference {aa*iSL} Returns {*iSLx} where :

insertion on output • i = 1, 2, 3 or 4 designating the channel number

• x = 0 for non-insertion; 1 for insertion

Get input level {aa*iSI} Returns {*iSIxxx} where :

• i = 1, 2, 3, or 4 designating the channel number

• xxx = input level in dBm

Get reference status {aaSE} Returns {SExy} where :

• x = setting: 0 for internal 10 MHz;

1 for external 10 MHz; 2 for auto detect

• y = currently selected in hardware :

0 for internal 10 MHz; 1 for external 10 MHz

Get reference offset (Option O) {aaSO} Returns {SOxxxxx} where :

• xxxxx = an offset amount between -2000 & +2000

2415-x02 Manual, Rev. E Page 7 09/28/17

(Status Request continued from page 7...)

TABLE 1.1 2415-x02 Statu

s Requests

Status Requests Conttinued

TABLE 1.1 2415-x02 Status Requests Continued

Command Syntax* Description

Get IF Frequency {aa*iSY} Returns {*iSYx} where :

(Option W140/70) • i = 1, 2, 3 or 4...

• x = 0 for 70 MHz IF, 1 for 140 MHz IF

Get IP address {aaSi} Returns {Sixxx.xxx.xxx.xxx} where :

(If Ethernet Option, W8, W18, or W

8, enabled) • xxx.xxx.xxx.xxx = IP address

Get subnet mask {aaSs} Returns {Ssxxx.xxx.xxx.xxx} where :

(If Ethernet Option, W8, W18, or W

8, enabled) • xxx.xxx.xxx.xxx = subnet mask

Get channel base parms {aa*iS1} Returns {*iS1tfffffffgggIIIma} where :

• i = 1, 2, 3 or 4 designating the channel number

• t=channel type: 0 for unused;

1 for upconverter; 2 for downconverter

• fffffff = frequency in KHz

• ggg = gain to nearest 1.0 dB (e.g., +25 = 25 dB)

• III = input level in dBm

• m = mute (0 = mute off, 1 = mute on)

• a = alarm: 0 for alarm off; 1 for alarm on

Get alarm status {aaSA} Returns {SAabcd} where:

• a=channel 1 alarm state (0 for alarm off; 1 for alarm on)

• b=channel 2 alarm state (0 for alarm off; 1 for alarm on)

• c=channel 3 alarm state (0 for alarm off; 1 for alarm on)

• d=channel 4 alarm state (0 for alarm off; 1 for alarm on)

Get product/model info {aaSV} Returns {SV2415-x02xxxver5.00} where:

• 2415-x02 = product model

• xxx = list of options, if any

•"ver"=separates model & options from firmware version

• 5.00 = firmware version

2415-x02 Manual, Rev. E Page 8 09/28/17

Table 1.2 lists the commands for the 2415-x02 and briefly describes them. After a command is sent the

2415-x02 sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only)

C = 1 character, either C (command) or S (status)

N = 1 character command or status request

D = 1 character or more of data (depends on command)

} = stop byte

*PLEASE NOTE:

Commands specific to a channel must be preceded

by *i where i is the channel number.

*PLEASE NOTE:

The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485 is selected.

Table 1.2 2415-x02 Comman

Commands

Table 1.2 2415-x02 Commands

Command Syntax* Description

Set Channel Frequency

{aa*iCFxxxxxxx}

where i = :

• 1, 2, 3 or 4 designating the channel number

• xxxxxxx = frequency in KHz

Set Channel Gain {aa*iCGxx} where i = :

• 1, 2, 3 or 4 designating the channel number

• xx = gain to nearest 1.0 dB (e.g., {1CGI5} sets channel 1 gain to 15 dB.)

Set input level {aa*iCIxxx} where i = :

• 1, 2, 3 or 4 designating the channel number

• xxx = input level in dBm,

(e.g., {*1CI-20} sets channel 1 input level to -20 dBm)

Set Channel Mute {aa*iCMx} where i = :

• 1, 2, 3 or 4 designating the channel number

• x = 1 for Mute ON (carrier OFF)

• x = 0 for Mute OFF (carrier ON)

10 MHz reference mode {aaCEx} where x = :

• 0 for internal 10 MHz; 1 for external 10 MHz; 2 for auto detect

Reference insertion on output {aa*iCLx} where :

• i = 1, 2, 3 or 4 designating the channel number

• x = 0 for non-insertion; 1 for insertion

Reference offset/adjust {aaCOxxxxx} where x = :

(Option O) • xxxxx = an offset amount between -2000 & +2000

IF Output Frequency {aa*iCYx} where i = :

(Option W140/70) • 1, 2, 3 or 4 designating the channel number

• x = 0 for 70 MHz IF, 1 for 140 MHz IF

2415-x02 Manual, Rev. E Page 9 09/28/17

1.4 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra. (Maximum Recommended Ambient Temperature)

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between units

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2415-x02 Manual, Rev. E Page 10 09/28/17

Table of contents

Other Cross Technologies Media Converter manuals

Cross Technologies

Cross Technologies 2116-184 User manual

Cross Technologies

Cross Technologies 4116-285-2450 User manual

Cross Technologies

Cross Technologies 2117-7172 User manual

Cross Technologies

Cross Technologies 2016-25 User manual

Cross Technologies

Cross Technologies 2015-05 User manual

Cross Technologies

Cross Technologies 2116-116 User manual

Cross Technologies

Cross Technologies 2017-03 User manual

Cross Technologies

Cross Technologies 2116-21-1014 User manual

Cross Technologies

Cross Technologies 2015-7075 User manual

Cross Technologies

Cross Technologies 2116-182193 User manual

Cross Technologies

Cross Technologies 2005-10 User manual

Cross Technologies

Cross Technologies 3116-192 User manual

Cross Technologies

Cross Technologies 2017-03A User manual

Cross Technologies

Cross Technologies 2015-58T User manual

Cross Technologies

Cross Technologies 3116-145-1600 User manual

Cross Technologies

Cross Technologies 2016-25-01 User manual

Cross Technologies

Cross Technologies 3116-7786-2150 User manual

Cross Technologies

Cross Technologies 2115-122 User manual

Cross Technologies

Cross Technologies 2416 02I Series User manual

Cross Technologies

Cross Technologies 2005-02P4 User manual

Cross Technologies

Cross Technologies 2416 25 Series User manual

Cross Technologies

Cross Technologies 2015-03A User manual

Cross Technologies

Cross Technologies 2415-02 Series User manual

Cross Technologies

Cross Technologies 2017-14 User manual

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide