Crestron CEN-TVAV User manual

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

Crestron CEN-TVAV Ethernet Enabled Programmable TV/AV Controller

Contents

Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV 1

Description 1

Functional Description 1

Physical Description 2

Leading Specifications 7

Setup 8

Cresnet Modular Cabling 8

Cable Configuration for Programming 8

Programming Cable Fabrication Specifications 9

Special Considerations for Using the RS-232 Port for Uploading Programs 10

Cable Configuration for Normal Operation 11

Loading Crestron Control Software 12

Installing Crestron Development Tools 12

Initial Setup 13

File Types 14

Obtaining Communications 17

Troubleshooting Communications 19

Loading the System Program 20

Loading Touchpanels 21

Updating the CEN-TVAV 21

Ethernet Setup 24

Initial IP Setup 24

IP Table Setup 26

Communicating via Ethernet 28

Troubleshooting Communications via Ethernet 28

Programming with SIMPL™Windows®or SIMPL+ 29

Programming Modes 30

Programming Descriptions 32

Example Programs 35

Problem Solving 35

Troubleshooting 35

Internal Fuse Replacement 36

Further Inquiries 38

Future Updates 38

Software License Agreement 39

Return and Warranty Policies 41

Merchandise Returns / Repair Service 41

CRESTRON Limited Warranty 41

Glossary of Terms 42

Operations Guide - DOC. 5720A Contents •i

Crestron CEN-TVAV Ethernet Enabled Programmable TV/AV Controller

Ethernet Enabled Programmable

TV/AV Controller: CEN-TVAV

Description

Functional Description

The CEN-TVAV is an Ethernet based, multi-purpose television/audio-visual

(TV/AV) device controller that is compatible with SIMPL™ Windows®. The

CEN-TVAV can communicate over an Ethernet/local area network (LAN) or wide

area network (WAN) using standard Internet protocol (IP) and can be used as a

standard Crestron remote control system (herein referred to as the Cresnet system)

peripheral or as a “smart” peripheral. As a standard Cresnet system peripheral, the

CEN-TVAV can be added as a Cresnet network device to a host CEN-TVAV,

CNMSXAV/PRO, or CNRACKX/-DP with all logic, infrared (IR) drivers, and serial

strings stored in the control system programming logic. In the “smart” peripheral

mode, the CEN-TVAV and may be programmed to store and execute SIMPL and

SIMPL+ programs.

The CEN-TVAV controls the ON/OFF and many or most functions of an attached

TV or AV device. The unit provides operating power to the device and controls the

device through a Crestron SmarTouch infrared probe (STIRP). The CEN-TVAV also

provides four Versiports ports (each capable of digital inputs/or digital outputs or

analog inputs) for controlling or monitoring external equipment.

The CEN-TVAV may also be enabled and operated with optional handheld IR

transmitters. To prevent interference from most standard IR frequencies and/or

fluorescent lighting, the CEN-TVAV and optional transmitters operate at 455

kilohertz (kHz). Contact Crestron customer service for further information.

The CEN-TVAV may be utilized as a “smart” peripheral, a standard Cresnet system

peripheral, or a “mixed mode” peripheral. For descriptions of the three ways to

perform different functions, refer to the following paragraphs.

In Local Processing Mode, the CEN-TVAV functions as a “smart” peripheral. The

built-in CEN-TVAV devices (IR Port, Versiport, Com Port, Power Sensor, and IR

Gateway) are accessed and controlled by the SIMPL Windows program loaded into

the CEN-TVAV.

Operations Guide - DOC. 5720A Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV •1

Ethernet Enabled Programmable TV/AV Controller Crestron CEN-TVAV

The CEN-TVAV was designed as a “scaled down” control system and does not

support dynamic preset storage that may be required by certain macros, such as

dynamic camera presets, etc. Having a simulated clock and simulated NVRAM, if

power is lost the clock and symbols utilizing NVRAM do not maintain previous

settings.

In Remote Processing Mode, a CEN-TVAV may be used as an Ethernet peripheral

within a host control system program. When this is done, all the functionality of the

CEN-TVAV (such as the IR Port, Versiport, Com Port, Power Sensor, and IR

Gateway) is accessed via the host control system program with no programming

within the CEN-TVAV. For example, IR can be generated by the CEN-TVAV by

programming the host control system only.

The Mixed Mode is a combination of the Local Processing and Remote Processing

Modes. For example, the Versiports can be programmed to control other equipment

from the program in the CEN-TVAV and the IR Port can be generated via the host

control system (no IR driver loaded in the CEN-TVAV). It is not recommended to

communicate to a port of the CEN-TVAV (such as the IR Port) through a program in

the CEN-TVAV itself and via a host control system.

Physical Description

Shown below is the STIRP and 5-pin connector plug that are supplied with the

CEN-TVAV. When connected to the IR port of the CEN-TVAV and positioned near

an attached TV or AV device, the STIRP (or other IR device) emits IR signals that

control the attached device. The provided 5-pin connector plug shown may be

connected to the I/O port of the CEN-TVAV and used for digital inputs, digital

outputs, and analog inputs to control and monitor up to four external devices.

CEN-TVAV Accessories

STIRP

(10 ft /

25.40 cm) 5-PIN

CONNECTOR

PLUG

The CEN-TVAV, shown on the next page, is housed in a black enclosure with silk-

screened labels on the front and rear panels. On the front panel are 15 light-emitting

diodes (LEDs) for indicating the status of the unit, the Ethernet that it is connected

to, and the attached device(s). All connections are made through the rear panel.

There are four rubber feet on the base of the unit for stability and to prevent slippage.

The CEN-TVAV is also available as an international version. All of the features are

identical with the exception of an international power-in cord and power out

receptacle, and unit nomenclature of CENI-TVAV. Throughout this operations

guide, all references to CEN-TVAV apply to both versions except where noted.

2 •Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV Operations Guide - DOC. 5720A

Crestron CEN-TVAV Ethernet Enabled Programmable TV/AV Controller

CEN-TVAV Physical Views

6.32 in

(16.06 cm)

1.70 in

(4.32 cm)

CRESNET RS-232

6.6A MAX

50-60HZ

115 VAC

POWER OUT 6A MAX

POWER IN

CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA

I/O

1234G

INPUT-OUTPUTETHERNET

TXDNETPWR RXD ERRLNK

1IR

TV/AV

PWR

RS-232

RXD TXD IR IN

CRESTRON

TVAV CONTROL

CEN-TVAV

ETHERNET

7.07 in

(17.95 cm)

CEN-TVAV Ports

Each CEN-TVAV rear panel port has a silk-screened label. For the descriptions of

the ports, refer to the two diagrams below and the paragraphs on the next two pages.

CEN-TVAV Rear Panel

CRESNETETHERNET RS-232

6.6A MAX

50-60HZ

115 VAC

POWER OUT 6A MAX

POWER IN

CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA

I/O

1234G

CENI-TVAV (International Version) Rear Panel

CRESNETETHERNET

I/O

RS-232

1IR

POWER OUT

5A MAX

230 VAC

POWER IN

50-60HZ, 5.5A MAX

CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA

234G

ETHERNET

Operations Guide - DOC. 5720A Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV •3

Ethernet Enabled Programmable TV/AV Controller Crestron CEN-TVAV

This 8-pin, 8-position RJ45 port connects the CEN-TVAV to a 10BaseT

Ethernet/LAN or WAN via a hub. Refer to the table below for the pinouts. A

standard (straight, non-cross-over type) Ethernet cable is required but not supplied.

NOTE: This port should NOT be connected to the UPLINK port of an Ethernet hub.

Ethernet Port Pinouts

PIN DESCRIPTION PIN DESCRIPTION

1 TX- (Transmit -) 5 Not Connected

2 TX+ (Transmit +) 6 RX- (Receive -)

3 RX+ (Receive +) 7 Not Connected

4 Not Connected 8 Not Connected

CRESNET

This 6-pin, 6-position RJ11 modular jack is used to connect the CEN-TVAV to a

control system so it may be accessed as a Cresnet peripheral. Refer to the table

below for the pinouts.

CAUTION: If making connections to RJ11 ports, use the Crestron 6-conductor

modular cable provided, DO NOT use 6-conductor telephone cables. Telephone

cables are wired in a crisscross fashion and are not compatible with Crestron

equipment. For further information, refer to the latest revision of Modular Cable

Requirements (Doc. 5682). This document can be obtained from the Downloads

page (CABLES and MANUAL Libraries) of Crestron’s website

(www.crestron.com). Search for MODULAR.PDF. New users are required to

NOTE: This port does NOT provide 24 direct current volts (VDC) for powering

other equipment.

CRESNET Port Pinouts

PIN DESCRIPTION PIN DESCRIPTION

1 Not Connected 4 NET- (Cresnet Z data)

2 Not Connected 5 GND

3 NET+ (Cresnet Y data) 6 GND

RS-232

This 6-pin, 6-position RJ11 modular jack is used for control of RS-232 peripheral

devices and to communicate with a personal computer (PC) when programming the

CEN-TVAV. Prior to switching between the programming mode and the RS-232

port, refer to “Special Considerations for Using the RS-232 Port for Uploading

Programs” on page 9. Refer to the table below for the pinouts.

RS-232 (PC) Port Pinouts

PIN DESCRIPTION PIN DESCRIPTION

1 CTS (Clear to Send) 4 TxD (Transmitted Data)

2 GND 5 RTS (Request to Send)

3 RxD (Received Data) 6 Not Connected

I/O (1-4, G)

Pins 1-4 of this Versiport may individually be used as programmable digital inputs,

digital outputs, analog inputs, or any combination of each. Digital inputs are rated 0 -

4 •Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV Operations Guide - DOC. 5720A

Crestron CEN-TVAV Ethernet Enabled Programmable TV/AV Controller

24VDC, 20K ohms input impedance, logic threshold 1.25VDC. Digital outputs offer

250 milliamp sink from maximum 24VDC; catch diodes provide transient protection

for use with “real world” loads. Analog inputs are rated 0 - 10VDC, protected to

24VDC maximum, 20K ohms input impedance; pin-programmable 2K ohms pullup

resistor to +5V. The pin labeled Gis the common ground for pins 1-4.

This 3.5mm mini-jack is used by the STIRP (provided) to control an attached TV or

AV device. The jack accepts mono (2-conductor) or stereo (3-conductor) mini-plugs.

Multiple IR drivers may be loaded into the CEN-TVAV and a ST-SPL may be used

for control of multiple AV devices.

POWER OUT

WARNING: When the POWER IN cord is plugged into an energized outlet,

POWER OUT becomes energized. Crestron recommends connecting the TV or AV

device before plugging the POWER IN cord into an outlet.

NOTE: The maximum continuous current from the POWER OUT under any

external load shall not exceed a current limit that is suitable for the minimum wire

gauge and maximum length used for the interconnecting cable(s).

NOTE: The maximum load applied to the POWER OUT shall not exceed the rated

voltage and current as specified on the unit.

This receptacle provides AC power (refer to the rear panel label for details) for a TV

or AV device. The receptacle is hard-wired to the POWER IN cord and is NOT

protected with a fuse.

The power out receptacle may be programmed to sense whether the attached device

is OFF or ON. A large current detected by the receptacle is used to indicate that the

attached device is ON and the absence of (or very low) current indicates the device is

OFF. If the CEN-TVAV (or control system) detects that the device is ON, the

program can be coded to not allow the CEN-TVAV to attempt to turn it ON, which

would inadvertently turn it OFF. This is true if the IR driver does not have discrete

ON and OFF functions, but only a POWER function.

POWER IN

This attached power cord supplies operating AC power (refer to the rear panel label

and/or “Leading Specifications” section of this guide for details) to the CEN-TVAV

and the POWER OUT port. An internal fuse electrically protects the CEN-TVAV

circuitry from excessive power input.

Operations Guide - DOC. 5720A Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV •5

Ethernet Enabled Programmable TV/AV Controller Crestron CEN-TVAV

CEN-TVAV Indicators

There are 15 LED indicators located on the front panel of the CEN-TVAV. For the

descriptions of the front panel indicators, refer to the diagram below and the

following paragraphs.

CEN-TVAV Front Panel

INPUT-OUTPUTETHERNET

TXDNETPWR RXD ERRLNK

1IR

TV/AV

PWR

RS-232

RXD TXD IR IN

CRESTRON

TVAV CONTROL

CEN-TVAV

PWR

This LED (green) is illuminated while the CEN-TVAV power-in cord is plugged

into an energized VAC outlet. There is no ON/OFF switch for the CEN-TVAV.

NET

This LED (yellow) illuminates when communication with Cresnet peripherals is

occurring or while processing commands from the PC (i.e., uploading,

programming). The connections to these devices are made through the rear panel

CRESNET port.

ETHERNET

These four front panel LEDs are active while the CEN-TVAV is connected to a LAN

or WAN through the rear panel ETHERNET port. The RXD (green) LED

illuminates during reception of Ethernet data and TXD (green) illuminates during

transmission of Ethernet data. The LNK (yellow) LED illuminates when there are

attachments to the Ethernet network and ERR (red) illuminates when an Ethernet

protocol error is detected.

INPUT-OUTPUT

These four LEDs (red) labeled 1-4 illuminate while the corresponding input or

output device that is connected to the rear panel I/O is active.

TV/AV

The PWR (green) LED is illuminated while the current sensor is detecting that the

TV or AV device connected to the power-out receptacle is ON. The IR (red) LED

illuminates when IR signals are being sent out the IR port.

RS-232

The RXD (red) LED illuminates when the CEN-TVAV is receiving serial data from

the RS-232 port. The TXD (red) LED illuminates when the CEN-TVAV is sending

data to the port.

NOTE: The IR receiver, for use with an optional handheld IR transmitter, is located

behind the red lens between the RS-232 and IR IN indicators.

IR IN

This LED (red) illuminates when the CEN-TVAV receives a valid IR code from an

optional handheld transmitter.

6 •Ethernet Enabled Programmable TV/AV Controller: CEN-TVAV Operations Guide - DOC. 5720A

Table of contents

Other Crestron Controllers manuals

Crestron

Crestron ST-VC User manual

Crestron

Crestron MPC-M10 Installation and operating instructions

Crestron

Crestron DM-RMC-4K-SCALER-C User manual

Crestron

Crestron CNXFZ User manual

Crestron

Crestron 4 Series User manual

Crestron

Crestron C2N-SDC How to use

Crestron

Crestron TSW-1050-FMKT User manual

Crestron

Crestron QM-RMC User manual

Crestron

Crestron MC2W Manual

Crestron

Crestron INET-IOEX-IRCOM User manual

Crestron

Crestron onCue BPC-8 Owner's manual

Crestron

Crestron CNECI-4A User manual

Crestron

Crestron PC-350V Series User manual

Crestron

Crestron infiNET HTT-B10X User manual

Crestron

Crestron ZUMMESH-JBOX-20A-SW User manual

Crestron

Crestron DigitalMedia Room Controller DM-RMC-100 How to use

Crestron

Crestron DM-RMC-SCALER-S How to use

Crestron

Crestron Zum ZUMMESH-CCO User manual

Crestron

Crestron HD-CTL-101 User manual

Crestron

Crestron 3 Series User manual

Crestron

Crestron DigitalMedia 8G+ DM-RMC-200-C Dimensional drawing

Crestron

Crestron IPAC User manual

Crestron

Crestron PC-200 Owner's manual

Crestron

Crestron CGDMX-512BI How to use

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual