Cognex DataMan 50 User manual

DataMan®50

Quick Reference Guide

04/18/2017

Version:5.7.0.102

Precautions

Observe these precautions when installing the Cognex product, to reduce the risk of

injury or equipment damage:

lTo reduce the risk of damage or malfunction due to over-voltage, line noise,

electrostatic discharge (ESD), power surges, or other irregularities in the

power supply, route all cables and wires away from high-voltage power

sources.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lCable shielding can be degraded or cables can be damaged or wear out

more quickly if a service loop or bend radius is tighter than 10X the cable

diameter. The bend radius must begin at least six inches from the

connector.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purpose only and may be changed

without notice.

Product Overview

1 Status LEDs:

- Power: YELLOW = Power ON

- Communication: Flashing YELLOW

- Good / bad read: GREEN = good read / RED = bad read

- Error: RED = error, check device log

2 Cable

3Internal illumination

43-position M12 lens

5 LED aimer

6 Mounting holes (M3 x 3.5 mm)

1 Remove side cover to access square nut (M3)

2 Yellow arrow indicates selected focus position

3 Hidden square nut as an alternative mounting option

DataMan 50 Accessories

CABLES

USB Cable, 1.5 m (DM100-USB-000),

USB Cable, 3 m (DM100-USB-030)

USB and Flying Leads I/O Cable, 2.0 m (DM-USBIO-00)

RS-232 and Flying Leads I/O Cable, 2.5 m (DM-RS232IO-00)

RS-232 Cable, 1.5 m (DM100-RS232-000),

Extension Cable, 5 m (DM100-EXTCBL-000)

Flying Leads Connection Cable, 5 m (DM50-PWRIO-05)

RS-232/USB adapter connector (DM100-PATCH-000)

LENS COVERS

Clear Front Cover (DM-50-CLCOV)

ESD-safe Front Cover (DM50-CLCOV-ESD)

OTHER

Power Supply, 6 V (DM100-PWR-000)

Pivot Mounting Bracket (DM100-PIVOTM-00)

Universal Mounting Bracket (DM50-UBRK-000)

Control Box (DM-CTRLBOX-00)

Dimensions

Field of View and Reading Distances

Connecting the Reader

Installation

Installation procedures and specifications are presented in detail in the DataMan®50

Reference Manual, which is installed with the DataMan Setup Tool. From the

Windows Start menu, select the following to access the manual: All Programs >

Cognex > DataMan Software vx.x.x > Documentation.

Note:

lCables are sold separately.

lIf any of the standard components appear to be missing or damaged,

immediately contact your Cognex Authorized Service Provider (ASP)

or Cognex Technical Support.

CAUTION:All cable connectors are “keyed” to fit the connectors on the

reader; do not force the connections or damage may occur.

Mounting

Mounting the DataMan reader at a slight angle (15°) can reduce reflections and

improve performance.

Use the set of mounting holes on the rear part to mount the DataMan reader.

Connect the Breakout Cable

Note: Unused wires can be clipped short or tied back using a tie made of non-

conductive material. For RS-232, use the Power Supply return path for

ground.

1. Verify that the power supply being used is unplugged and not receiving

power.

2. Connect the cable on the back of the device to either a USB adapter cable

with power tab or to an RS-232 adapter cable with power tab.

3. Connect a 6 V power supply.

4. Restore power to the power supply and turn it on if necessary.

Install Software and Documentation and

Connect the Reader

Follow the steps below to connect your reader to power and network:

1. Connect the USB or RS-232 cable to your reader.

2. Connect the cable to a power supply.

To configure a DataMan 50 reader, the DataMan Setup Tool software must be

installed on a networked PC. The DataMan Setup Tool is available from the

DataMan support site: http://www.cognex.com/support/dataman.

1. After installing the software, connect the DataMan 50 reader to your PC.

2. Launch the DataMan Setup Tool and click Refresh.

3. Select your DataMan 50 reader from the list and click Connect.

Other manuals for DataMan 50

Table of contents

Other Cognex Barcode Reader manuals

Cognex

Cognex DataMan 470 Series User manual

Cognex

Cognex DataMan 300 Series User manual

Cognex

Cognex DataMan 7550 User manual

Cognex

Cognex DataMan 150 User manual

Cognex

Cognex DataMan 475 User manual

Cognex

Cognex In-Sight 2800 Series User manual

Cognex

Cognex DataMan 470 Series User manual

Cognex

Cognex DataMan 9500 User manual

Cognex

Cognex DM260Q User manual

Cognex

Cognex DataMan 50 Series User manual

Cognex

Cognex DataMan 60 Series User manual

Cognex

Cognex DataMan 8700 User manual

Cognex

Cognex DataMan 8600 Verifier Series User manual

Cognex

Cognex DataMan 8072 DL User manual

Cognex

Cognex DataMan 8700 User manual

Cognex

Cognex VisionPro Trevista CI Dome User manual

Cognex

Cognex DataMan 8072 User manual

Cognex

Cognex DataMan 50 User manual

Cognex

Cognex DataMan 280 Series User manual

Cognex

Cognex DataMan 8050 User manual

Cognex

Cognex In-Sight SnAPP Series User manual

Cognex

Cognex DataMan 300 Series User manual

Cognex

Cognex DataMan 380 Series User manual

Cognex

Cognex DataMan 300 Series User manual

Cognex DataMan 50 User manual

Popular Barcode Reader manuals by other brands