Cognex DataMan 60 User manual

DataMan®60

Quick Reference Guide

2019 October 08

Revision: 6.1.6SR1.5

Precautions

To reduce the risk of injury or equipment damage, observe the following precautions

when you install the Cognex product:

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Product Overview

1 Internal illumination

2 3-position lens cap

3 Focal position indicator

4 External illumination connector

5Status LEDs

6 LED aimer

7Lens

1 Directly connected cable terminating in a DB15 connector providing: power, I/O, USB, and

RS-232 connectivity

2 Ethernet RJ-45 connector

3 Mounting points

DataMan 60 Accessories

CABLES

USB Cable, 1.5 m (DM100-USB-000),

USB Cable, 3 m (DM100-USB-030)

USB and Flying Leads I/O Cable, 2.0 m (DM-USBIO-00)

RS-232 and Flying Leads I/O Cable, 2.5 m (DM-RS232IO-00)

RS-232 Cable, 1.5 m (DM100-RS232-000),

Extension Cable, 5 m (DM100-EXTCBL-000)

Flying Leads Connection Cable, 5 m (DM50-PWRIO-05)

RS-232/USB adapter connector (DM100-PATCH-000)

Ethernet Cable: use CBL-C10E or any standard CAT5/5e, SF/FTP or S/FTP

cable

OTHER

Power Supply, 6 V (DM100-PWR-000)

Pivot Mounting Bracket (DM100-PIVOTM-00)

Universal Mounting Bracket (DM50-UBRK-000)

Control Box (DM-CTRLBOX-00)

Dimensions

Field of View and Reading Distances

Focus position Distances in mm/2D min. code Distances in mm/1D min. code

45 mm 33-51 6 MIL 34-51 4 MIL

31-57 8 MIL 30-56 6 MIL

27-60 10 MIL 37-66 10 MIL

25-61 12 MIL

70 mm 44-74 6 MIL 52-73 4 MIL

42-78 8 MIL 45-83 6 MIL

39-80 10 MIL 33-89 10 MIL

34-89 12 MIL

110 mm 58-121 10 MIL 66-122 6 MIL

54-133 12 MIL 50-141 10 MIL

58-168 15 MIL

Connecting the Reader

Perform the following steps:

1. Connect the breakout cable.

2. Connect the reader to the PC.

3. Connect the reader to an Ethernet network with a standard CAT5/5e,

SF/FTP or S/FTP cable.

For information on the pinout and the wire colors, see section Connections, Optics

and Lighting in the DataMan 60 ReferenceManual.

Installation

Installation procedures and specifications are presented in detail in the DataMan®60

Reference Manual, which is installed with the DataMan Setup Tool. From the

Windows Start menu, select the following to access the manual: All Programs >

Cognex > DataMan Software vx.x.x > Documentation.

Note:

lCables are sold separately.

lIf a standard component is missing or damaged, immediately contact

your Cognex Authorized Service Provider (ASP) or Cognex

Technical Support.

CAUTION:All cable connectors are keyed to fit the connectors on the reader.

Do not force the connections or damage may occur.

Mounting

Mounting the DataMan reader at a slight angle (15°) can reduce reflections and

improve performance.

Use the set of mounting holes on the rear part to mount the DataMan reader.

Connect the Ethernet Cable

1. Connect the Ethernet cable's RJ-45 connector to a switch/router or PC, as

applicable.

Connect the Breakout Cable

Note: You can clip unused wires short or use a tie made of non-conductive

material to tie them back. For RS-232, use the Power Supply return path for

ground.

1. Verify that the power supply being used is unplugged and not receiving

power.

2. Connect the cable on the back of the device to an RS-232 adapter cable

with power tab.

3. Connect a 6 V power supply.

4. Restore power to the power supply and turn it on if necessary.

Install Software and Documentation and

Connect the Reader

Follow the steps below to connect your reader to power and network:

1. Connect the RS-232 cable to your reader.

2. Connect the cable to a power supply.

To configure a DataMan 60 reader, the DataMan Setup Tool software must be

installed on a networked PC. The DataMan Setup Tool is available from the

DataMan support site: http://www.cognex.com/support/dataman.

1. After installing the software, connect the DataMan 60 reader to your PC.

2. Launch the DataMan Setup Tool and click Refresh.

3. Select your DataMan 60 reader from the list and click Connect.

Other manuals for DataMan 60

Table of contents

Cognex DataMan 60 User manual

Popular Barcode Reader manuals by other brands