Code Alarm CATX2LED Operating instructions

Model CATX2LED

Programming Guide

The keychain transmitters included with the system have been pre-programmed at the factory,

with each button pre-assigned to control a specific function of the system.

The system will store codes from up to 8 different transmitters. If a 9th transmitter is

programmed to the system, then the first transmitter programmed to the system will be

erased from the system’s memory.

To program new or additional transmitters, the alarm must be disarmed and out of valet mode:

1. Open the drivers door (verify that the vehicle’s interior light turns on.

2. Turn the ignition key to the ON or RUN position.

3. Press and hold the emergency override button

3a. After 10 seconds the horn will honk three (3) times. This indicates

that the system has entered transmitter programming mode.

4. Release the emergency override button.

5. Press the LOCK icon button on the remote transmitter to be programmed.

5a. The horn/siren will sound 1 time, indicating that the system has

“learned” that remote transmitter.

6. Repeat step 5 for any additional remote transmitters.

Deleting Lost or Stolen Remote Controls from Your System

If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to

remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls

to Your System.

3a. If you have only one remaining remote control, press the

LOCK button on that remote control four (4) times, pausing

at least 1 second in between each press. The horn must

“honk” each time you press the LOCK button.

3b. If you have two remaining remote controls, press the LOCK

button on each remote control two (2) times, pausing at least

1 second in between each press. The horn must “honk” each

time you press the LOCK button.

3c. If you have three remaining remote controls, press the

LOCK button on two of the remote controls one (1) time, then press the

LOCK button on the remaining remote control twice. Pause at

least 1 second in between each press. The horn must “honk”

each time you press the LOCK button.

4. Turn the vehicle ignition off to exit the programming mode. When you are finished, the lost

or stolen remote control will no longer operate your system.

Changing the Remote Control Battery

The 3-volt lithium (CR2450) battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Remove the small phillips head screw from the bottom

cover of the transmitter.

2. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

4. Remove the old battery and replace with a new one. Be

sure to observe the (+) and (-) signs in the battery

compartment.

4. Carefully snap the case halves back together, rerplace

the small phillips head screw in the bottom of the

transmitter cover and test the remote control.

Model CATX2LED

Programming Guide

Table of contents

Other Code Alarm Car Alarm manuals

Code Alarm

Code Alarm CA 170 User manual

Code Alarm

Code Alarm SRT 1600 User manual

Code Alarm

Code Alarm CATX2LCD Operating instructions

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm CA 521 User manual

Code Alarm

Code Alarm Professional Series CA 1050 User manual

Code Alarm

Code Alarm CATX110 Operating instructions

Code Alarm

Code Alarm CA-140 User manual

Code Alarm

Code Alarm Elite ca1155E User manual

Code Alarm

Code Alarm CA 420 User manual

Code Alarm

Code Alarm CA 180 User manual

Code Alarm

Code Alarm ELITE Series User manual

Code Alarm

Code Alarm PowerCode PC 7300 User manual

Code Alarm

Code Alarm CA-135 User manual

Code Alarm

Code Alarm ca 1552 Professional Series User manual

Code Alarm

Code Alarm TW-1 User manual

Code Alarm

Code Alarm CA1B5 User manual

Code Alarm

Code Alarm CATX610 Operating instructions

Code Alarm

Code Alarm Professional Series CA 1550 User manual

Code Alarm

Code Alarm CA- 550 User manual

Code Alarm

Code Alarm CA 6151 User manual

Code Alarm

Code Alarm CA-670 User manual

Code Alarm

Code Alarm ca1555 User manual

Code Alarm

Code Alarm ca6554 User manual

Popular Car Alarm manuals by other brands

Clifford

Clifford 3606X owner's guide

Ultra Start

Ultra Start 2500M SERIES install guide

Ultra Start

Ultra Start 650 Series owner's manual

Audiovox

Audiovox Prestige Platinum+ APS-511C owner's manual

Sparkrite

Sparkrite SRA8 Guide

Viper

Viper 4708V owner's manual

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Installation and maintenance manual

Falcon

Falcon Predator XL3 Installer manual

Audiovox

Audiovox Auto Security XR91 Programming guide

Clifford

Clifford Sabre II owner's manual

CrimeStopper

CrimeStopper CS-8717 Wiring diagram

Ultra Start

Ultra Start 450 SERIES install guide

Scytek electronic

Scytek electronic Vectra X3 product manual

Excalibur

Excalibur AL-1860-EDPB Operation guide

Clifford

Clifford CYBER 2 owner's manual

Gemini

Gemini 7057 user manual

FlashLogic

FlashLogic FLRSBA PRESTIGE Product guide

Magicar

Magicar FAI-440 manual