Code Alarm CATX130 Operating instructions

Model CATX130

Programming Guide

The keychain transmitters included with the system have been pre-programmed at the factory,

with each button pre-assigned to control a specific function of the system.

The system will store codes from up to 8 different transmitters. If a 9th transmitter is

programmed to the system, then the first transmitter programmed to the system will be

erased from the system’s memory.

To program new or additional transmitters, the alarm must be disarmed and out of valet mode:

1. Open the drivers door (verify that the vehicle’s interior light turns on.

2. Turn the ignition key to the ON or RUN position.

3. Press and hold the emergency override button

3a. After 10 seconds the horn will honk three (3) times. This indicates

that the system has entered transmitter programming mode.

4. Release the emergency override button.

5. Press the LOCK icon button on the remote transmitter to be programmed.

5a. The horn/siren will sound 1 time, indicating that the system has

“learned” that remote transmitter.

6. Repeat step 5 for any additional remote transmitters.

Deleting Lost or Stolen Remote Controls from Your System

If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to

remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls

to Your System.

3a. If you have only one remaining remote control, press the

LOCK button on that remote control eight (8) times, pausing

at least 1 second in between each press. The horn must

“honk” each time you press the LOCK button.

3b. If you have two remaining remote controls, press the LOCK

button on each remote control four (4) times, pausing at least

1 second in between each press. The horn must “honk” each

time you press the LOCK button.

3c. If you have three remaining remote controls, press the

LOCK button on two of the remote controls three (3) times, then press the

LOCK button on the remaining remote control twice. Pause at

least 1 second in between each press. The horn must “honk”

each time you press the LOCK button.

4. Turn the vehicle ignition off to exit the programming mode. When you are finished, the lost

or stolen remote control will no longer operate your system.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one.

Be sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX130

Programming Guide

Table of contents

Other Code Alarm Car Alarm manuals

Code Alarm

Code Alarm CA 420 User manual

Code Alarm

Code Alarm Professional Series CA 1550 User manual

Code Alarm

Code Alarm CA 421 User manual

Code Alarm

Code Alarm Power Elite PC 4100 User manual

Code Alarm

Code Alarm 2000 User manual

Code Alarm

Code Alarm Professional Series CA 1050 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm CA 6551 SST User manual

Code Alarm

Code Alarm CA 170 User manual

Code Alarm

Code Alarm ELITE Series User manual

Code Alarm

Code Alarm ca 1051 User manual

Code Alarm

Code Alarm CA100 User manual

Code Alarm

Code Alarm CATX510 Operating instructions

Code Alarm

Code Alarm CA 6151 User manual

Code Alarm

Code Alarm CATX120 Operating instructions

Code Alarm

Code Alarm Car Alarm CA-310 User manual

Code Alarm

Code Alarm 420A User manual

Code Alarm

Code Alarm CA 1150 User manual

Code Alarm

Code Alarm CA 650 User manual

Code Alarm

Code Alarm CA 510 User manual

Code Alarm

Code Alarm CA1355E User manual

Code Alarm

Code Alarm F50 User manual

Code Alarm

Code Alarm 2000 User manual

Code Alarm

Code Alarm caSEC Installation and operating manual

Popular Car Alarm manuals by other brands

Clifford

Clifford 3606X owner's guide

Ultra Start

Ultra Start 2500M SERIES install guide

Ultra Start

Ultra Start 650 Series owner's manual

Audiovox

Audiovox Prestige Platinum+ APS-511C owner's manual

Sparkrite

Sparkrite SRA8 Guide

Viper

Viper 4708V owner's manual

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Installation and maintenance manual

Falcon

Falcon Predator XL3 Installer manual

Audiovox

Audiovox Auto Security XR91 Programming guide

Clifford

Clifford Sabre II owner's manual

CrimeStopper

CrimeStopper CS-8717 Wiring diagram

Ultra Start

Ultra Start 450 SERIES install guide

Scytek electronic

Scytek electronic Vectra X3 product manual

Excalibur

Excalibur AL-1860-EDPB Operation guide

Clifford

Clifford CYBER 2 owner's manual

Gemini

Gemini 7057 user manual

FlashLogic

FlashLogic FLRSBA PRESTIGE Product guide

Magicar

Magicar FAI-440 manual