Clarke CSJ1500 User manual

USER INSTRUCTIONS

GC0414

1.5 TONNE SCISSOR JACK

MODEL NO: CSJ1500

PART NO: 7624015

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Scissor Jack.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

LIFTING OPERATIONS AND LIFTING EQUIPMENT

REGULATIONS 1998 (LOLER)

This jack, depending on use, may fall within the scope of LOLER. It is the

owner’s responsibility to determine whether or not it does and, if so, to comply

with any applicable requirements in LOLER, for having the jack thoroughly

examined.

SPECIFICATION

Rated Load 1.5 Tonne

Min height of saddle 95 mm

Max height of saddle 390 mm

Length of handle 415 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

• Ensure that the jack is in good working order. Have any damaged

parts repaired or replaced immediately. Use genuine Clarke parts

only. The use of unauthorised parts may be dangerous and will

invalidate the warranty.

• Operate the jack in a suitable, well lit work area.

• Keep the work area clean and tidy and free from unrelated items.

• Use the jack on level and solid ground, preferably concrete. Avoid

soft/unmade ground as the jack may sink in.

• Ensure the vehicle handbrake is engaged, the engine/motor is

switched off and the transmission is in 1st or reverse gear. (or park for

automatics)

• Ensure a minimum distance of 0.5 m between vehicle and static

objects such as doors, walls, etc, to allow for the vehicle tilting.

• Only place the jack under those lifting points recommended by the

vehicle manufacturer (see vehicle handbook).

• Check the lifting point is rigid and centred on the jack saddle.

• Ensure there are no passengers in the vehicle.

• Place chocks under the wheels of the vehicle.

• Ensure all non-essential persons keep a safe distance whilst the jack

is in use.

• Use suitable capacity axle stands under the vehicle before

proceeding with any task.

• Ensure there are no personnel or obstructions under the vehicle

before lowering.

•Use the jack for lifting only, NOT for supporting the vehicle.

• Take care not to trap fingers in the moving parts of the jack.

•Do not operate the jack if damaged.

•Do not work under the vehicle until axle stands have been correctly

positioned.

•Do not allow personnel to operate the jack unless they have read

these safety precautions.

•Do not use the jack for purposes other than that for which it is

designed.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

•Do not exceed the rated capacity of the jack.

•Do not jack up a vehicle if there is a risk of spillage of fuel, battery

acid or other dangerous substances.

•Do not allow the vehicle to move while supported by the jack.

•Ensure that you can see the saddle and jacking point throughout

the jacking operation in case there is any relative movement.

• Never tamper with the product or modify it in any way, as this could

prove to be dangerous and will invalidate the guarantee. Only use

the product for the purpose for which it is intended.

• When not in use, store the jack, fully lowered, in a safe, dry,

childproof area.

OPERATING INSTRUCTIONS

1. Prepare the vehicle as mentioned in the safety precautions ensuring the

ground on which the jack is to stand is level and solid.

2. Position the jack saddle under the vehicle manufacturers recommended

lifting point.

3. No responsibility can be accepted for incorrect use of the jack.

Warning: IT IS VERY DANGEROUS TO GO UNDER A VEHICLE WHICH IS

SUPPORTED BY A JACK EVEN IF ADDITIONAL SUPPORTS ARE USED. DO

NOT GO UNDER A VEHICLE UNLESS IT IS SUPPORTED BY ADEQUATELY

RATED AXLE STAND

WARNING: BEFORE LIFTING, ENSURE THE SAFETY PRECAUTIONS ARE

STRICTLY FOLLOWED.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

LIFTING THE VEHICLE

1. Turn the handle clockwise to bring

the jack saddle into contact with

the recommended lifting point.

2. Ensure the jack is vertical before

continuing to turn the handle

clockwise and raising the vehicle

to the required working height.

Turn the handle slowly and evenly

to ensure no sudden movements

of the vehicle.

LOWERING THE VEHICLE

1. Slowly turn the handle anti-clockwise to lower the vehicle.

MAINTENANCE

IMPORTANT: Only fully qualified personnel should attempt maintenance or

repair.

• Keep the jack clean and lubricate all moving parts with oil on a

regular basis.

• Before each use check for broken, cracked, bent, or loose parts, or

any visible damage to welds, saddle, frame and all parts including

pins and other fasteners. If any suspect item is found remove jack

from service and take necessary action to remedy the problem.

• Do not use the jack if believed to have been subjected to abnormal

load or shock. Inspect and take appropriate action.

WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER AND

ENSURE THERE ARE NO PERSONS OR OBSTACLES BENEATH THE VEHICLE,

OR IN THE PATH OF ITS DESCENT.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST & DIAGRAM

No Description No Description

1 Saddle 8 Handle

2 Saddle Rivet 9 Threaded Rod

3 Upper Arm 10 Lower Arm

4 Safety Label 11 Inner Stay

5 Collar 12 Base

6 Hinge 13 Base Rivet

7 Bearing 14 Hinge

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

Table of contents

Other Clarke Jack manuals

Clarke

Clarke CTJ1800A Instruction Manual

Clarke

Clarke strong-arm CBJ30 Troubleshooting guide

Clarke

Clarke CFTJ500 Troubleshooting guide

Clarke

Clarke CTJ10GLS Instruction Manual

Clarke

Clarke Strong-Arm CTJ1500QULP Installation and operation manual

Clarke

Clarke STRONG-ARM CTJ2LP Instruction Manual

Clarke

Clarke CTJ2000A Installation and operation manual

Clarke

Clarke STRONG-ARM CTJ3000G User manual

Clarke

Clarke CTJ2000G User manual

Clarke

Clarke STRONG-ARM CFJ48B User manual

Clarke

Clarke STRONG-ARM CTJ3000G Instruction Manual

Clarke

Clarke Strong-Arm CTJ100 Installation and operation manual

Clarke

Clarke STRONG-ARM CTJ2GLC User manual

Clarke

Clarke CTBJ5 Troubleshooting guide

Clarke

Clarke STRONG-ARM CBJ2 Installation and operation manual

Clarke

Clarke STRONG-ARM CML3 Quick reference guide

Clarke

Clarke STRONG-ARM CTJ5GLB Instruction Manual

Clarke

Clarke Strong-Arm CFT5 Guide

Clarke

Clarke CTJ2500SUV Instruction Manual

Clarke

Clarke CTJ30 Troubleshooting guide

Clarke

Clarke CBJ32 Instruction Manual

Clarke

Clarke Strong-Arm CTJ2250LP Instruction Manual

Clarke

Clarke CTT320 User manual

Clarke

Clarke Strong Arm CTJ1250AB Installation and operation manual

Popular Jack manuals by other brands

Omega Lift Equipment

Omega Lift Equipment 18122C Operating instructions & parts manual

Pittsburgh

Pittsburgh 58816 Owner's manual & safety instructions

Unimec

Unimec TP Assembly instructions

Sonic

Sonic 4800703 instructions

BGS technic

BGS technic 70039 instruction manual

TradeQuip

TradeQuip 1128T owner's manual

VEVOR

VEVOR TJD-12000SP-F quick start guide

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK operating instructions

Stels

Stels 51131 user manual

Bushranger

Bushranger RJX01 instruction manual

Valex

Valex 1650520 Translation of the original instructions

Pfaff

Pfaff Merkur M0 Operating instruction

Beta

Beta 3050/K Operation manual and instructions

Sealey

Sealey 1050CXHV manual

Jung

Jung JH Series operating instructions

URIAH

URIAH UC200020 quick start guide

Kennedy

Kennedy KSJ010 instruction manual

Grizzly

Grizzly H8097 quick start guide