Cisco SNS-3415 series User manual
Cisco SNS-3400 Series Appliance Hardware Installation Guide
First Published: 2016-11-23
Last Modified: 2016-11-23
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number:
©Cisco Systems, Inc. All rights reserved.
CONTENTS
CHAPTER 1
Cisco SNS 3400 Series Appliance Overview 1
Cisco SNS 3415 and Cisco SNS-3495 Appliances 1
Cisco SNS 3415 and SNS 3495 Appliances Hardware Specifications 1
LED Indicators on Cisco SNS-3415 and 3495 Appliances 2
Cisco SNS-3415 or 3495 Appliance Front Panel View 3
Cisco SNS 3415 or SNS 3495 Appliance Back Panel View 6
Internal Diagnostic LEDs 8
Regulatory Compliance 9
CHAPTER 2
Before You Begin 11
Safety Guidelines 11
Unpack and Inspect the Server 12
Prepare for Server Installation 13
Installation Guidelines 14
Rack Requirements 15
Equipment Requirements 15
Slide Rail Adjustment Range 15
Server Specifications 15
Physical Specifications 15
Environmental Specifications 16
Power Specifications 16
650-Watt Power Supply 16
CHAPTER 3
Install the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances 19
Install the Cisco SNS 3415 and Cisco SNS 3495 Hardware Appliances 19
Install the Cisco SNS 3415 or 3495 Appliance in a Rack 20
Install the Side Rails 20
Install the Cable Management Arm (Optional) 23
Cisco SNS-3400 Series Appliance Hardware Installation Guide
iii
Connect Cables 24
Connect the Network Interface 24
Connect the Console 25
Connect the Keyboard and Video Monitor 25
Cable Management 26
Connect and Power On the Cisco SNS 3415 or 3495 Appliance 26
Connect and Power On the Server (Standalone Mode) 27
NIC Modes and NIC Redundancy Settings 28
System BIOS and CIMC Firmware 29
Update the BIOS and Cisco IMC Firmware 29
Access the System BIOS 30
Cisco Integrated Management Controller 30
Setup CIMC Configuration Utility 30
Cisco SNS-3400 Series Appliance Hardware Installation Guide
iv
Contents
CHAPTER 1
Cisco SNS 3400 Series Appliance Overview
•Cisco SNS 3415 and Cisco SNS-3495 Appliances, page 1
•Cisco SNS 3415 and SNS 3495 Appliances Hardware Specifications, page 1
•Internal Diagnostic LEDs, page 8
•Regulatory Compliance, page 9
Cisco SNS 3415 and Cisco SNS-3495 Appliances
The Cisco SNS 3415 or Cisco SNS 3495 server is designed for performance and density over a wide range
of business workloads, from web serving to distributed databases.
Building on the success of the Cisco SNS 3415 or Cisco SNS 3495 server, the enterprise-class Cisco SNS
3415 or Cisco SNS 3495 server further extends the capabilities of the Cisco Unified Computing System
portfolio in a 1U form factor. The Cisco SNS 3415 or Cisco SNS 3495 server does this with the addition of
the Intel Xeon processor E5-2600 product family, which delivers significant performance and efficiency gains.
In addition, the Cisco SNS 3415 Cisco SNS 3495 server offers up to 256 GB of RAM, 8 drives, and 2 x 1
GbE lights-out management (LOM) ports that deliver outstanding levels of density and performance in a
compact package.
Cisco SNS 3415 and SNS 3495 Appliances Hardware
Specifications
The following table describes the hardware specifications of Cisco SNS 3415 and Cisco SNS 3495 appliances.
Cisco SNS-3400 Series Appliance Hardware Installation Guide
1
DiagramsHardware SpecificationsCisco Identity Services Engine
Appliance
Cisco SNS-3415 or 3495
Appliance Front Panel View, on
page 3
Cisco SNS 3415 or SNS 3495
Appliance Back Panel View , on
page 6
•Cisco UCS C220 M3
•Single socket Intel E5-2609
2.4Ghz CPU 4 total cores, 4
total threads
•16 GB RAM
•1 x 600-GB disk
•Embedded Software RAID 0
•4 GE network interfaces
•For physical, environmental,
and power specifications, see
Server Specifications, on
page 15
Cisco SNS-3415-K9
•Cisco UCS C220 M3
•Dual socket Intel Xeon
E5-2609 2.4GHz CPU 8 total
cores, 8 total threads
32 GB RAM
2 x 600-GB disks
RAID 0+1
4 GE network interfaces
For physical, environmental,
and power specifications, see
Server Specifications, on
page 15.
Cisco SNS-3495-K9
LED Indicators on Cisco SNS-3415 and 3495 Appliances
This section describes the front- and rear-panel controls, ports, and LED indicators on the Cisco SNS 3415
or Cisco SNS 3495 appliances.
•Cisco SNS-3415 or 3495 Appliance Front Panel View, on page 3
•Cisco SNS 3415 or SNS 3495 Appliance Back Panel View , on page 6
Cisco SNS-3400 Series Appliance Hardware Installation Guide
2
Cisco SNS 3400 Series Appliance Overview
LED Indicators on Cisco SNS-3415 and 3495 Appliances
Cisco SNS-3415 or 3495 Appliance Front Panel View
The following figure shows the components of the Cisco SNS-3415 or Cisco SNS-3495 appliance front panel
view.
Figure 1: Cisco SNS-3415/3495 Appliance Front View
Power supply status LED6Power button/Power status LED1
Network link activity LED7Identification button/LED2
Asset tag (serial number)8System status LED3
9 KVM connector (used with KVM cable
that provides two USB, one VGA, and one
serial connector)
9Fan status LED4
Drives (up to eight hot-swappable 2-5-inch
drives)
10Temperature status LED5
The following table describes the LEDs located on the front panel of the Cisco SNS-3415 or Cisco SNS-3495
appliance.
StateFront Panel LED Names
•Off—There is no AC power to the server.
•Amber—The server is in standby power mode.
Power is supplied only to the Cisco IMC and
some motherboard functions.
•Green—The server is in main power mode.
Power is supplied to all server components.
Power button/Power status LED
Cisco SNS-3400 Series Appliance Hardware Installation Guide
3
Cisco SNS 3400 Series Appliance Overview
Cisco SNS-3415 or 3495 Appliance Front Panel View
StateFront Panel LED Names
•Off—The identification LED is not in use.
•Blue—The identification LED is activated.
Identification
•Green—The server is running in normal
operating condition.
•Green, blinking—The server is performing
system initialization and memory check.
•Amber, steady—The server is in a degraded
operational state. For example:
◦Power supply redundancy is lost.
◦CPUs are mismatched.
◦At least one CPU is faulty.
◦At least one DIMM is faulty.
◦At least one drive in a RAID configuration
failed.
•Amber, blinking—The server is in a critical
fault state. For example:
◦Boot failed.
◦Fatal CPU and/or bus error is detected.
◦Server is in an over-temperature condition.
System status
•Green—All fan modules are operating properly.
•Amber, steady—One or more fan modules
breached the critical threshold.
•Amber, blinking—One or more fan modules
breached the non-recoverable threshold.
Fan status
•Green—The server is operating at normal
temperature.
•Amber, steady—One or more temperature
sensors breached the critical threshold.
•Amber, blinking—One or more temperature
sensors breached the non-recoverable threshold.
Temperature status
Cisco SNS-3400 Series Appliance Hardware Installation Guide
4
Cisco SNS 3400 Series Appliance Overview
Cisco SNS-3415 or 3495 Appliance Front Panel View
StateFront Panel LED Names
•Green—All power supplies are operating
normally.
•Amber, steady—One or more power supplies
are in a degraded operational state.
•Amber, blinking—One or more power supplies
are in a critical fault state.
Power supply status
•Off—The Ethernet link is idle.
•Green—One or more Ethernet LOM ports are
link-active, but there is no activity.
•Green, blinking—One or more Ethernet LOM
ports are link-active, with activity.
Network link activity
•Off—The hard drive is operating properly.
•Amber—Drive fault detected.
•Amber, blinking—The device is rebuilding.
Hard drive fault
•Off—There is no hard drive in the hard drive
tray (no access, no fault).
•Green—The hard drive is ready.
•Green, blinking—The hard drive is reading or
writing data.
Hard drive activity
Cisco SNS-3400 Series Appliance Hardware Installation Guide
5
Cisco SNS 3400 Series Appliance Overview
Cisco SNS-3415 or 3495 Appliance Front Panel View
Cisco SNS 3415 or SNS 3495 Appliance Back Panel View
The following figure shows the components of the Cisco SNS-3415 and Cisco 3495 appliance back panel
view.
Figure 2: Cisco SNS-3415/3495 Appliance Rear View
Table 1:
Serial port (RJ-45 connector)7Power supplies (up to two)1
1-GB Ethernet dedicated management
port used to access CIMC (labeled M)
8Slot 2: Low-profile Peripheral
Component Interconnect Express (PCIe)
slot on riser (half-height, half-length, x16
connector, x16 lane width)
2
1-GB Ethernet port 1 (GigE0) for Cisco
ISE management communication
9Slot 1: PCIe1 card containing 1-GB
Ethernet ports (GigE2 and GigE3)
3
1-GB Ethernet port 2 (GigE1)101-GB Ethernet port 3 (GigE2)4
USB Ports111-GB Ethernet port 4 (GigE3)5
Rear identification button12VGA video connector6
The following table describes the LEDs located on the back panel of the Cisco SNS-3415 or Cisco SNS-3495
appliance.
Cisco SNS-3400 Series Appliance Hardware Installation Guide
6
Cisco SNS 3400 Series Appliance Overview
Cisco SNS 3415 or SNS 3495 Appliance Back Panel View
Other manuals for SNS-3415 series
2
This manual suits for next models
1
Table of contents
Other Cisco Server manuals
Cisco
Cisco UCS C220 M4 User manual
Cisco
Cisco UCS E Series User manual
Cisco
Cisco AS5200 - Universal Access Server User manual
Cisco
Cisco UCS B22 M3 User manual
Cisco
Cisco UCS C460 M4 Installation and operation manual
Cisco
Cisco UCS 6500 Series User manual
Cisco
Cisco UCS B200 M4 Manual
Cisco
Cisco UCS 5100 Use and care manual
Cisco
Cisco C880 M4 User manual
Cisco
Cisco UCS B200 Manual
Cisco
Cisco UCS C240 M3 User manual
Cisco
Cisco C880 M4 User manual
Cisco
Cisco UCS B420 M3 User manual
Cisco
Cisco SE-CL-L3 User manual
Cisco
Cisco Firepower Management Centers User manual
Cisco
Cisco UCS B200 M3 Manual
Cisco
Cisco UCS S3260 M5 Guide
Cisco
Cisco UCS 5100 Quick start guide
Cisco
Cisco C220 M3 Manual
Cisco
Cisco TelePresence Server 7010 Reference guide
