Cisco Profile Series User manual
Contents
Introduction
Prerequisites
Components Used
Configure
Introduction
This guide is inteded to show you how to configure 'Just a bunch of disks' (JBOD) on the Cisco
12G SAS Modular RAID Controller in a C-Series server.
Caveats:
* JBOD disks are not able to take advantage of any hardware caching on the RAID controller.
http://www.redbooks.ibm.com/redpapers/pdfs/redp5234.pdf (general documentation on RAID /
JBOD)
* If caching is required on these disks, then you can put them into a RAID 0 array (striping) and
present this to the OS. Recall that RAID0 has no parity, so please note that the more disks added
to a RAID 0, the larger your failure domain, or the greater the chance of data loss across all disks
due to a single disk failure. This is the nature of RAID 0. Good performance, intolerant of even a
single disk failure. This is acceptable for some applications and use cases however.
Prerequisites
C-Series Server
●
Cisco 12G SAS Modular Raid Controller
●
1 or more HDD
●
Access to CIMC / KVM
●
Components Used
Cisco C240-M4 running 2.0(6d) CIMC
●
Cisco 12G SAS Modular Raid Controller running 4.250.00-3632
●
Configure
As a safety precaution, if you have a pre-existing RAID configuration, please back up the data on
that Virtual Disk (VD) prior to making these changes.
If you have existing Virtual Disk (VD), RAID 1 for instance, that you wish to preserve, its
configuration should be preserved after enabling JBOD, though a reboot is required to enter the
pre-boot RAID configuration menu (CTRL+R) to enable JBOD.
At the time of this writing, it appears that JBOD is disabled on the controller by default, and cannot
be enabled on the 12G Controller via the CIMC, only the pre-boot RAID Configuration menu
(CTRL+R).
If you wish for ALL disks to be JBOD, then delete any existing Virtual Disks (VD) on the RAID.
This should release the Physical Disks (PD) into 'Unconfigured Good'. This can be done via
CIMC or CTRL+R pre-boot RAID configuration menus. This should be expected to delete data
on any Virtual Disk that you Delete so back up important data accordingly.
Confirm if JBOD is enabled or disabled already:
1) Log into CIMC.
2) Click Storage > Select 12G controller > Controller Info tab.
Enable JBOD
1) If disabled, reboot the host, and press CTRL+R to enter the RAID configuration screens.
2) Press CTRL+N twice, navigate to 'Enable JBOD' and press 'space'. Ensure that the [X] shows
in the square brackets.
3) Press CTRL+S to save.
4) Press Escape to exit.
5) This will convert ALL available disks to JBOD. Again, in my testing, it did not convert PD
allocated to VD (RAID 1) to JBOD, and my OS was still in tact on that RAID 1.
6) Confirm JBOD is enabled.
If you don't already have a Virtual Disk (VD), then you can configure some number of disks as
'Unconfigured Good' so you can add them to a new Virtual Disk (VD) or RAID Volume.
You can now toggle the disks between 'Unconfigured Good' (which can be added to RAID) or
'JBOD' from within the CIMC.
You will find that for any PD that is a member of a VD / RAID Group, you do not have the option
convert it to JBOD. The PD must be removed from the VD / RAID Group prior to getting the option
to convert it to a JBOD disk.
Other manuals for Profile Series
10
Table of contents
Other Cisco Server manuals
Cisco
Cisco UCS C220 M4 Quick start guide
Cisco
Cisco CDE 220 Series Manual
Cisco
Cisco UCS 5100 Quick start guide
Cisco
Cisco UCS Series User manual
Cisco
Cisco UCS 6500 Series User manual
Cisco
Cisco UCS B460 M4 Manual
Cisco
Cisco UCS C240 M3 User manual
Cisco
Cisco NCS 1001 User manual
Cisco
Cisco SNS-3515 series Manual
Cisco
Cisco MCS-78 Series Administrator guide
Cisco
Cisco UCS C460 M2 User manual
Cisco
Cisco UCS C240 M3 User manual
Cisco
Cisco UCS C220 User manual
Cisco
Cisco UCS B200 M3 Manual
Cisco
Cisco UCS Invicta C3124SA User manual
Cisco
Cisco IE-3000-8TC Instruction Manual
Cisco
Cisco C460 M4 User manual
Cisco
Cisco 3500 Series User manual
Cisco
Cisco UCS 5100 Use and care manual
Cisco
Cisco 7513 Series Guide
