Cisco NM-1A-T3 - 1port Ds3 Atm Network Module User manual

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Configuring the Cisco NM-1A-T3/E3 Network

Module

OL-10215-01

First Published: June 28, 2007

The Cisco NM-1A-T3/E3 (or ATM T3/E3) network module provides Asynchronous Transfer Mode

(ATM) services on a T3 or E3 connection. This feature module explains how to configure the ATM

T3/E3 network module for each connection. The ATM T3/E3 network module is supported on

Cisco 2800 and Cisco 3800 routers and includes the following features:

•ATM traffic management features including constant bit rate (CBR), variable bit rate (VBR),

available bit rate (ABR), unspecified bit rate (UBR), and UBR+

•Classic IP over ATM encapsulation (RFC 1577)

•Multiprotocol encapsulation over ATM adaptive layer 5 (AAL5) segmentation (RFC 1483)

•Point-to-Point Protocol (PPP) over ATM

•LAN Emulation (LANE)

Finding Feature Information in This Module

Your Cisco IOS software release may not support all the features documented in this module. To reach

links to specific feature documentation in this module and to see a list of the releases in which each feature is

supported, see the “Feature Information for the Cisco ATM T3/E3 Network Module” section on page 26.

Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS

software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. You do

not need an account on Cisco.com.

Contents

•Restrictions for the Cisco ATM T3/E3 Network Module, page 2

•Information About the Cisco ATM T3/E3 Network Module, page 2

•How to Configure the ATM T3/E3 Network Module, page 4

Configuring the Cisco NM-1A-T3/E3 Network Module

Restrictions for the Cisco ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

•SVCs, page 11

•Customizing the ATM T3/E3 Network Module, page 15

•Configuration Example, page 16

•Recommendations for Watermark Settings, page 16

•Additional References, page 19

•Command Reference, page 21

•Feature Information for the Cisco ATM T3/E3 Network Module, page 26

•Obtaining Documentation, Obtaining Support, and Security Guidelines, page 6

Restrictions for the Cisco ATM T3/E3 Network Module

The following restrictions apply to the Cisco ATM T3/E3 network module:

•There is no default card type configuration on the ATM T3/E3 network module. You must configure

the ATM T3/E3 network module for T3 or E3 before it will work.

•The atm vc-per-vp command is not supported on the ATM T3/E3 network module.

Information About the Cisco ATM T3/E3 Network Module

To configure the Cisco ATM T3/E3 network module, you should understand the following:

•ATM, page 2

•Permanent Virtual Circuits, page 3

•Switched Virtual Circuits, page 3

•Classes of Service, page 4

ATM

ATM is an International Telecommunication Union-Telecommunications Standards Section (ITU-T)

standard for cell relay wherein information for multiple service types (such as voice, video, and data),

is conveyed in small, fixed-size (53-byte) cells via connection-oriented virtual circuits (VCs).

Virtual Circuits

A virtual circuit (VC) is a point-to-point connection between remote hosts and routers. A VC is

established for each ATM end node with which the router communicates. The characteristics of the VC

are established when the VC is created and include the following:

•Classes of Service

•ATM adaptation layer 5 (AAL5)

•Encapsulation type:

–

Logical link control Subnetwork Address Protocol (AAL5SNAP)

–

Multiplexer (AAL5MUX)

Configuring the Cisco NM-1A-T3/E3 Network Module

Information About the Cisco ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

–

Network Layer Protocol ID (AAL5NLPID)

–

Integrated Local Management Interface (ILMI)

–

Switched Multimegabit Data Service (SMDS)

–

ITU/Q.2931 Signaling ATM Adaptation Layer (QSAAL)

–

Cisco AUTO PPP over AAL5 (aal5autoppp)

–

Cisco PPP over AAL5 (aal5ciscoppp)

Each VC supports the following router functions:

•Multiprotocol switching

•Fast switching of IP packets

•Flow, and Cisco Express Forwarding (CEF) switching of IP packets

•Pseudo-broadcast support for multicast packets

By default, CEF switching is enabled on all ATM T3/E3 module interfaces. These switching features can

be turned off by using interface configuration commands. Flow must be explicitly enabled for each

interface.

Permanent Virtual Circuits

To use a permanent virtual circuit (PVC), configure the PVC in both the router and the ATM switch.

PVCs remain active until the circuit is removed from either configuration. When a PVC is configured,

all the configuration options are passed on to the OC-3 module. You can write these PVCs into NVRAM;

they are used when the system image is reloaded.

Some ATM switches might have point-to-multipoint PVCs that do the equivalent of broadcasting. A

point-to-multipoint PVC can be used as the sole broadcast PVC for all multicast requests.These

switching features can be turned off by using interface configuration commands. Flow must be explicitly

enabled for each interface.

Switched Virtual Circuits

ATM switched virtual circuit (SVC) service operates much like X.25 SVC service, although ATM allows

much higher throughput. Virtual circuits are created and released dynamically, providing user bandwidth

on demand. This service requires a signaling protocol between the router and the switch.

The ATM signaling software provides a method of dynamically establishing, maintaining, and clearing

ATM connections at the user-network interface (UNI). The ATM signaling software conforms to ATM

Forum UNI 3.0 or ATM Forum UNI 3.1, depending on what version is selected by interim local

management interface (ILMI) or configuration.

In UNI mode, the user is the router and the network is an ATM switch. This is an important distinction.

The Cisco router does not perform ATM-level call routing. Instead, the ATM switch does the ATM call

routing, and the router routes packets through the resulting circuit. The router performs as the user and

the LAN interconnection device at the end of the circuit, and the ATM switch performs as the network.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

Classes of Service

ATM resources can be specified dynamically on a per-connection basis (per SVC). The ATM T3/E3

network module supports four classes of service:

•Constant Bit Rate (CBR): This class emulates circuit switching. CBR has the highest transport

priority, which is 0. CBR can be used for connections such as voice and video. This bandwidth is

characterized by peak cell rate (PCR).

•Variable Bit Rate (VBR): VBR is available in non-real-time (VBR-nrt) and real-time (VBR-rt). VBR

has the second highest transport priority, which is 1. VBR sends traffic at a rate that varies with time,

depending on the availability of user information.

•Available Bit Rate (ABR): ABR has the transport priority of 2. ABR provides rate-based flow

control and is aimed at data traffic.

•Unspecified Bit Rate (UBR): UBR has the transport priority of 3. UBR is a “best effort” class of

service that uses the unutilized bandwidth for a connection. Traffic categorized as UBR+ is

guaranteed a minimum line rate through the minimum cell rate (MCR) traffic parameter.

How to Configure the ATM T3/E3 Network Module

To configure the ATM T3/E3 network module, complete the following procedures:

•Configuring the Card Type, page 4

•Changing the Card Type, page 5

•Enabling the ATM Interface, page 7

•Configuring PVCs, page 7

Configuring the Card Type

To configure the ATM T3/E3 network module for T3 or E3 operation, perform the following tasks.

Note The ATM T3/E3 network module will not be operational until a card type is configured.

SUMMARY STEPS

1. enable

2. configure terminal

3. card type {t3 | e3} slot

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

DETAILED STEPS

Changing the Card Type

To change the ATM T3/E3 network module for T3 or E3 operation, perform the following tasks:

SUMMARY STEPS

1. enable

2. configure terminal

3. no card type {t3 | e3}

4. card type {t3 | e3} slot

5. reload

Command or Action Purpose

Step 1 enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 card type {t3|e3} slot

Example:

Router(config)# card type t3 1

Specifies T3 or E3 connectivity for the ATM T3/E3 network

module.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

DETAILED STEPS

Note When changing from T3 card type to E3 card type make sure that the interface is configured for 34 Mbps

or less. This is the maximum bandwidth for an E3 connection.

Troubleshooting Tip

T3 interfaces support a maximum bandwidth of 44,209 kbps in ATM and 40,700 kbps in physical layer

convergence procedures (PLCP) mode. E3 interfaces support a maximum bandwidth of 33,920 kbps in

ATM and 30,528 kbps in PLCP mode.

If the total bandwidth used by an interface is greater than 34 Mbps and the card type is changed from T3

to E3, the traffic shaping characteristics of the VCs will be changed. The Cisco IOS software will

reconfigure the VCs so that the total allocated guaranteed bandwidth does not exceed the maximum

allowable E3 bandwidth.

Command or Action Purpose

Step 1 enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 no card type {t3 | e3}

Example:

Router(config)# no card type t3

Optional. Removes any previously configured card type.

Step 4 card type {t3 | e3} slot

Example:

Router(config)# card type t3 1

Specifies T3 or E3 connectivity for the ATM T3/E3 network

module.

Step 5 reload

Example:

Router(config)# reload

Reloads the router so that changes can take affect.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

Enabling the ATM Interface

To enable the ATM T3/E3 interface, perform the following tasks, starting in global configuration mode.

SUMMARY STEPS

1. interface ATM slot

2. atm clock internal

3. no shut down

DETAILED STEPS

Configuring PVCs

To use a PVC, you must configure the PVC into both the router and the ATM switch. PVCs remain active

until the circuit is removed from either configuration.

To configure a PVC, perform these tasks:

•Creating a PVC

•Mapping a Protocol Address to a PVC

•Configuring the AAL and Encapsulation Type

•Configuring PVC Traffic Parameters

•Setting PVC Watermarks, page 10

Command or Action Purpose

Step 1 interface ATM slot

Example:

Router(config)# interface ATM 1

Enters interface configuration mode.

Step 2 atm clock internal

Example:

Router(config-if)# atm clock internal

Mandatory if the ATM port the network module is

connected to is configured line. Optional otherwise.

Specifies ATM clock source. Default source is line.

Step 3 no shutdown

Example:

Router(config)# no shutdown

(Optional) Enables the ATM interface, thereby beginning

the segmentation and reassembly (SAR) operation on the

interface. The ATM interface is enabled by default.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

Creating a PVC

To create a PVC on the ATM interface and enter interface-ATM-VC configuration mode, use the

following command, beginning in interface configuration mode:

The range of values for vpi isfrom 0 to 255. The range of values for vci is from 1 to 65535.

Once you specify a name for a PVC, you can reenter the interface-ATM-VC configuration mode by

simply entering pvc name.

Mapping a Protocol Address to a PVC

The ATM interface supports a static mapping scheme that identifies the network addresses of remote

hosts or routers. This section describes how to map a PVC to an address, which is a required task for

configuring a PVC.

To map a protocol address to a PVC, use the following command in interface-ATM-VC configuration

mode:

Note If you enable or disable broadcasting directly on a PVC by using the protocol command, this

broadcasting configuration will take precedence over any direct configuration made using the broadcast

command.

Command Purpose

Router(config-if)# pvc [name] vpi/vci [ilmi | qsaal]

Example:

Router(config-if)# pvc cisco 0/16 ilmi

Configures a new ATM PVC by assigning a name (optional)

and VPI/VCI values. Enters interface-ATM-VC

configuration mode. Optionally configures ILMI or QSAAL

encapsulation.

Command Purpose

Router(config-if-atm-vc)# protocol protocol

protocol-address [ [no] broadcast]

Example:

Router(config)# protocol ip 10.68.34.237 broadcast

Maps a protocol address to a PVC.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

Configuring the AAL and Encapsulation Type

To configure the ATM adaptation layer (AAL) and encapsulation type on a VC, use the following

command, beginning in interface-ATM-VC configuration mode:

For a description of AAL types, see the encapsulation aal5 command in the “ATM Commands” chapter

of the Cisco IOS Wide-Area Networking Command Reference.

Configuring PVC Traffic Parameters

The supported traffic parameters (or classes of service) for the ATM T3/E3 network module are CBR,

real-time and non-real-time VBR, UBR, UBR+, and ABR.

To configure PVC traffic parameters on a VC, use one of the following commands, beginning in

interface-ATM-VC configuration mode:

Command Purpose

Router(config-if-atm-vc)# encapsulation {aal2 |

aal5auto | aal5autoppp virtual-template number

[group group-name] | aal5ciscoppp virtual-template

number | aal5mux protocol | aal5nlpid | aal5snap}

Example:

Router(config-if-atm-vc)# encapsulation aal5auto

Configures the ATM adaptation layer (AAL) and

encapsulation type on the VC.

Command Purpose

Router(config-if-atm-vc)# abr output-pcr output-mcr

Example:

Router(config-if-atm-vc)# abr 10000 3000

Configures ABR.

Router(config-if-atm-vc)# ubr output-pcr

Example:

Router(config-if-atm-vc)# ubr 10000

Configures UBR.

Router(config-if-atm-vc)# ubr+ output-pcr output-mcr

Example:

Router(config-if-atm-vc)# ubr+ 10000 3000

Configures UBR+.

Router(config-if-atm-vc)# vbr-nrt output-pcr

output-scr output-mbs

Example:

Router(config-if-atm-vc)# vbr-nrt 10000 5000 64

Configures non-real-time VBR.

Configuring the Cisco NM-1A-T3/E3 Network Module

How to Configure the ATM T3/E3 Network Module

Cisco IOS Release 12.4(15)T

The -pcr, -scr, and -mcr arguments are peak cell rate, sustainable cell rate, and guaranteed minimum cell

rate, respectively, in kbps. The -mbs argument is maximum burst size in number of cells.

The peak rate, average rate, and rate arguments are in kbps. The burst argument is in number of cells.

For ABR VCs, you can optionally configure the factor by which the cell transmission rate increases or

decreases in response to flow control information from the network or destination. To configure this

option, use the following command in interface-ATM-VC configuration mode:

Setting PVC Watermarks

The SAR, which is used by the ATM T3/E3 module, uses queues inside the SAR hardware. One queue

is used for each created PVC. To manage the latency, shaping, and throughput on the PVCs, use the

following command in interface-ATM-VC configuration mode:

Router(config-if-atm-vc)# vbr-rt peak-rate

average-rate burst

Example:

Router(config-if-atm-vc)# vbr-rt 10000 3000 64

Configures real-time VBR.

Router(config-if-atm-vc)# cbr rate

Example:

Router(config-if-atm-vc)# cbr 10000

Configures CBR.

Command Purpose

Router(config-if-atm-vc)# atm abr rate-factor

[rate-increase-factor] [rate-decrease-factor]

Example:

Router(config-if-atm-vc)# atm abr rate-factor 32 32

Specifies the ABR rate factors. The default rate increase

factor is 16. The default rate decrease factor is 16.

Command Purpose

Router(config-if-atm-vc)# queue-depth <hwm> <lwm>

Example:

Router(config-if-atm-vc)# queue-depth 10 5

Sets the high watermark (hwm) and low watermark (lwm)

level for each created PVC.

When the number of ATM cells in the SAR queues reach the

high watermark level, the SAR stops processing the ATM

cells on that particular PVC. After the ATM cells drain to the

low watermark level, the SAR starts processing the ATM

cells again.

This manual suits for next models

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco WEC600N User manual

Cisco

Cisco Edge 300 Series Quick start guide

Cisco

Cisco MDS 9500 Series Manual

Cisco

Cisco Cisco ONS 15600 SDH User manual

Cisco

Cisco CSC-C2FCIT Instruction Manual

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet User manual

Cisco

Cisco 2610 - Router - EN User manual

Cisco

Cisco Firepower 1010 User manual

Cisco

Cisco VPN 3002 Hardware Client Manager User manual

Cisco

Cisco ISE - Line Card ISE User manual

Cisco

Cisco C7200-I - Input/Output Controller - Control... User manual

Cisco

Cisco MXE 3000 Manual

Cisco

Cisco ON100 Network Agent User manual

Cisco

Cisco IPS 7.1 User manual

Cisco

Cisco ESR-PRE2 User manual

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Operator's manual

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - User manual

Cisco

Cisco 5400 Instruction Manual

Cisco

Cisco NCS 4206 Instruction Manual

Cisco

Cisco ASA Quick start guide

Cisco

Cisco IAD2430 Series Manual

Cisco

Cisco NCS 6008 LCC Instruction Manual

Cisco

Cisco Cisco ONS 15600 SDH User manual

Cisco

Cisco MERAKI MX75 User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide