Cisco Edge 300 Series Quick start guide

Last updated on October 15, 2015

Edge300FirmwareUpgrade

Introduction

This guide outlines the steps to upgrade the firmware on the Cisco Edge 300 and will be described in two

stages:

Preparing a bootable USB drive containing the desired Edge 300 firmware

Flashing the firmware onto the Edge 300 device

Prerequisites

Cisco Edge 300 device

1 USB flash drive formatted in FAT32 file system (minimum 2GB free space)

1 Edge 300 firmware image file (for use with the USB flash drive)

1 paper clip / SIM eject tool (for the recessed reset button)

Note:

Empty the contents of the USB flash drive for the purpose of Edge firmware flashing. The process

of creating a bootable flash drive will temporarily render it unusable for conventional storage and

transferring of files. The flash drive can later be reformatted back to its original file system once the

firmware upgrade has completed.

PreparingaBootableUSBDrive

1. From your computer, copy the Edge 300 firmware image into the root directory of the USB flash

drive. Disconnect the USB drive from your computer and connect it to the USB port of the Edge 300,

located on the side of the device.

2. SSH into the device using either PuTTy (on a Windows PC) or Terminal (on a Mac) using the

commands shown below. Replace {device IP} with the actual IP address of the Edge device. (verify

with your network administrator regarding the correct IP address and root credentials for the Edge

300).

3. Use the blkid command to locate the USB drive. (usually /dev/sdxx with xx being b1, b2 or c1, c2

etc.) For this guide, we will assume it is /dev/sdb1.

4. Mount the USB drive.

5. Unmount the USB drive. Copy the firmware image onto the Edge 300 device (into the /apps/

directory). Wait for the task to finish. The copying of the image file will be completed when the

console displays a # symbol at the beginning of the command line.

6. Without ejecting your USB drive, run the following commands (remember to replace sdb1 with your

blkid if discovered to be different from Step 3). Note that each command will take some time to

execute. Wait until each command has completed (console displays a #) before proceeding to the

next command. When all commands have been executed, remove the USB drive from the device.

#sshroot@{deviceIP}

#root@{deviceIP}password:cisco

#blkid

/dev/sdb1:LABEL="USBDRIVE"UUID="7288-0792"TYPE="vfat"

#mount/dev/sdb1/tmp/mnt

#cp/tmp/mnt/smi-usb-sunbird-1.5.0-delivery.tar.gz/apps/

#umount/tmp/mnt

FlashingtheFirmware

1. Press and hold the power button on the Edge 300 to turn it OFF. Connect the newly created

bootable USB drive into the USB port again, located on the side of the device.

2. Press and hold the power button on the Edge 300 to turn it back ON. Using your paper clip / SIM

eject tool, press and hold the reset button located next to the power button of the device for about 5

seconds until the device reboots itself.

#mkfs.ext3/dev/sdb1

#mount/dev/sdb1/tmp/mnt

#tarxvzf/apps/smi-usb-sunbird-1.5.0-delivery.tar.gz–C/tmp/mnt/

#umount/tmp/mnt

3. Once rebooted, the Edge 300 device will read the contents of the USB drive and begin flashing the

firmware. The power LED will be flashing continuously at this point, indicating the firmware update is

in process. The firmware flashing will be completed when you are able to view the login screen on a

connected display.

© 2018 Appspace Inc. All Rights Reserved | Legal | Give Feedback

Other manuals for Edge 300 Series

1

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco MGX 8260 Quick start guide

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Quick reference guide

Cisco

Cisco CPS-MSP-1RU-K9 User manual

Cisco

Cisco ONS 15454 Instruction Manual

Cisco

Cisco Linksys WES610N User manual

Cisco

Cisco UCS 6248 UP User manual

Cisco

Cisco 220 Series Smart Plus User manual

Cisco

Cisco IAD2430 Series Manual

Cisco

Cisco Firepower 1010 User manual

Cisco

Cisco Aironet 340 Series User manual

Cisco

Cisco ONS 15327 Operator's manual

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... User manual

Cisco

Cisco Cisco ASA Series User manual

Cisco

Cisco NCS 1002 User manual

Cisco

Cisco OSM-12CT3/T1 - Optical Services Module... Quick guide

Cisco

Cisco NSS4100 - Gigabit Storage System Instruction Manual

Cisco

Cisco PIX Series Manual

Cisco

Cisco ONS 15454 User manual

Cisco

Cisco CGR 1000 Series User manual

Cisco

Cisco OL-7822-06 User manual

Cisco

Cisco Secure Firewall Management Center 1700 User manual

Cisco

Cisco ONS 15310-CL User manual

Cisco

Cisco GS7000 User manual

Cisco

Cisco ISA500 Series Instruction Manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide