Cisco LightStream 1010 Manual

Cisco Firepower 1010 Hardware Installation Guide

First Published: 2019-07-24

Last Modified: 2019-09-26

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com

go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any

other company. (1721R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown

for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

CONTENTS

Overview 1

CHAPTER 1

Features 1

Package Contents 4

Serial Number Location 5

Front Panel 6

Rear Panel 6

Status LEDs 7

Hardware Specifications 9

Product ID Numbers 10

Power Cord Specifications 10

Installation Preparation 17

CHAPTER 2

Installation Warnings 17

Position the Chassis 20

Safety Recommendations 20

Maintain Safety with Electricity 21

Prevent ESD Damage 21

Site Environment 22

Site Considerations 22

Power Supply Considerations 22

Rack Configuration Considerations 23

Mount the Chassis 25

CHAPTER 3

Unpack and Inspect the Chassis 25

Desktop-Mount the Chassis 26

Wall-Mount the Chassis 26

Cisco Firepower 1010 Hardware Installation Guide

iii

Rack-Mount the Chassis 29

Connect to the Console Port 33

CHAPTER 4

Connect to the Console Port with Microsoft Windows 33

Connect to the Console Port with Mac OS X 35

Connect to the Console Port with Linux 35

Cisco Firepower 1010 Hardware Installation Guide

Contents

CHAPTER 1

Overview

•Features, on page 1

•Package Contents, on page 4

•Serial Number Location, on page 5

•Front Panel, on page 6

•Rear Panel, on page 6

•Status LEDs, on page 7

•Hardware Specifications, on page 9

•Product ID Numbers, on page 10

•Power Cord Specifications, on page 10

Features

The Cisco Firepower 1010 security appliance is an NGFW desktop product in the Cisco Firepower family of

devices with PoE+ and L2 switch support.

The PoE+ and L2 switch features are supported starting with Firepower Version 6.5.

Note

The Firepower 1010 supports Cisco Firepower software version 6.4 and later. See the Cisco Firepower

Compatibility Guide, which provides Cisco Firepower software and hardware compatibility, including operating

system and hosting environment requirements, for each supported Firepower version.

See Product ID Numbers, on page 10 for a list of the product IDs (PIDs) associated with the Firepower 1010.

The following figure shows the Cisco Firepower 1010.

Cisco Firepower 1010 Hardware Installation Guide

Figure 1: Firepower 1010

The following table lists the features for the Firepower 1010.

Table 1: Firepower 1010 Features

DescriptionFeature

1 RUForm factor

Desktop mount

Wall mount (Cisco part number 69-100647-01)

Rack mount (Cisco part number 69-100648-01)

Mounting

Side-to-side

No fan

Airflow

One 4-core Intel CPUProcessor

8-GB DDR4 DRAMMemory

8 GB (internal)Boot partition

Marvell SOHO 88E6390

First supported in Firepower Verion 6.5.

Note

L2 switch

One Gigabit Ethernet RJ-45 10/100/1000 BaseT

Restricted to network management access; connect with an RJ-45 cable

Management

port

One RJ-45

Use to access management through an external system

Console port

One USB Mini B

Use to access management through an external system

USB Mini B

port

One USB 3.0 Type A

Use to attach an external device such as storage

USB port

Cisco Firepower 1010 Hardware Installation Guide

Overview

Features

Eight Gigabit Ethernet RJ-45 10/100/1000 BaseT

Each RJ-45 (8P8C) copper port supports auto MDI/X as well as auto-negotiation for

interface speed, duplex, and other negotiated parameters, and are MDI/MDIX-compliant.

The ports are numbered (from top to bottom, left to right) 1, 2, 3, 4, 5, 6, 7, 8. Each port

includes a pair of LEDs, one each for connection status and link status. The ports are

named and numbered Gigabit Ethernet 1/1 through Gigabit Ethernet 1/8.

You can use ports 7 and 8 as PoE+ ports. PoE+ is first supported in Firepower

Version 6.5.

Note

Network ports

Ports 7 and 8 are PoE+ ports; first supported in Firepower Version 6.5.

Note

PoE+ controller

card

Accepts a standard Kensington T-bar locking mechanism for securing the chassisLock slot

A small recessed button that if pressed for longer than three seconds resets the chassis to

its default state following the next reboot. Configuration variables are reset to factory

default, but the flash is not erased and no files are removed.

Reset button

To shut down the Firepower 1010, remove the AC power supply.

To shut down the Firepower 1010 gracefully, see the "Power Off the Device"

topic for FDM and FMC in the Cisco Firepower 1010 Getting Started Guide.

Note

Power switch

The chassis is powered on when you plug in the AC power supply.Power cord

socket

One external AC power supply

The power supply has a total of 115 W of power. There is 55 W of +12-V system power

and 60 W of -53.5-V PoE power.

PoE+ is first supported in Firepower Version 6.5.

Note

Use the power supply (part number 341-100765-01) that shipped with the

chassis. It supports PoE+.

Note

AC power

supply

One 200-GB M.2 SATA SSD drive

The drive is used by the software; there is no user access to the drive.

The drive is not field-replaceable; you must return the chassis to Cisco for drive

replacement.

Storage

Four rubber feet on the bottom of the chassis

The rubber feet are needed for proper cooling. Do not remove them.

Note

Rubber feet

Console Ports

The Firepower 1010 has two external console ports, a standard RJ-45 port and a USB Mini B serial port.

Only one console port can be active at a time. When a cable is plugged into the USB console port, the

RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port, the RJ-45

Cisco Firepower 1010 Hardware Installation Guide

Overview

Features

port becomes active. The console ports do not have any hardware flow control. You can use the CLI to

configure the chassis through either serial console port by using a terminal server or a terminal emulation

program on a computer.

• RJ-45 (8P8C) port—Supports RS-232 signaling to an internal UART controller. The RJ-45 console

port does not support a remote dial-in modem. You can use a standard management cable (Cisco

part number 72-3383-01) to convert the RJ45-to-DB9 connection if necessary.

•USB Mini B port—Lets you connect to a USB port on an external computer. For Linux and Macintosh

systems, no special driver is required. For Windows systems, you must download and install a USB

driver (available on software.cisco.com). You can plug and unplug the USB cable from the console

port without affecting Windows HyperTerminal operations. We recommend shielded USB cables

with properly terminated shields. Baud rates for the USB console port are 1200, 2400, 4800, 9600,

19200, 38400, 57600, and 115200 bps.

For Windows operating systems, you must install a Cisco Windows USB Console Driver on any PC

connected to the console port before using the USB console port. See Connect to the Console Port with

Microsoft Windows, on page 33 for information on installing the driver.

Note

External Flash Storage

The chassis contains a standard USB Type A port that you can use to attach an external device. The USB

port can provide output power of 5 V and up to a maximum of 1A (5 USB power units).

• External USB drive (optional)—You can use the external USB Type A port to attach a data-storage

device. The external USB drive identifier is disk1. When the chassis is powered on, a connected

USB drive is mounted as disk1 and is available for you to use. Additionally, the file-system

commands that are available to disk0 are also available to disk1, including copy,format,delete,

mkdir,pwd,cd, and so on.

• FAT-32 File System—The Firepower 1010 only supports FAT-32-formatted file systems for the

external USB drive. If you insert an external USB drive that is not in FAT-32 format, the system

mounting process fails, and you receive an error message. You can enter the command format

disk1: to format the partition to FAT-32 and mount the partition to disk1 again; however, data might

be lost.

Package Contents

The following figure shows the package contents for the Firepower 1010. Note that the contents are subject

to change and your exact contents might contain additional or fewer items.

Cisco Firepower 1010 Hardware Installation Guide

Overview

Package Contents

Figure 2: Firepower 1010 Package Contents

USB console cable (Type A to Type B)2Chassis1

Power supply4Power cord3

Start Here: Cisco Firepower 1010

This document tells how to cable and set up the

Firepower 1010 for FTD with FDM and ASA

with ASDM, and it sends you to the online Useful

Links document to continue your configuration.

Serial Number Location

You can view the serial number and additional model information on the compliance label located on the

bottom of the chassis. The following figure shows a sample compliance label.

Cisco Firepower 1010 Hardware Installation Guide

Overview

Serial Number Location

Figure 3: Compliance Label on the Firepower Chassis

Front Panel

The following figure shows the front panel of the Firepower 1010. Note that there are no connectors or LEDs

on the front panel.

Figure 4: Firepower 1010 Front Panel

Rear Panel

The following figure shows the rear panel of the Firepower 1010. See Status LEDs, on page 7 for a description

of the LEDs.

Cisco Firepower 1010 Hardware Installation Guide

Overview

Front Panel

Other manuals for LightStream 1010

Table of contents

Other Cisco Network Hardware manuals

Cisco

Cisco NCS 1004 User manual

Cisco

Cisco MERAKI CW9166D1 User manual

Cisco

Cisco NCS 1004 User manual

Cisco

Cisco UCS 6248 UP User manual

Cisco

Cisco ASA 5506-X Manual

Cisco

Cisco NCS 1002 User manual

Cisco

Cisco IAD2430 Series Installation guide

Cisco

Cisco CX-FEIP-1FX= Installation and con?guration User manual

Cisco

Cisco IP/VC 3500 Original instructions

Cisco

Cisco Engine 611 User manual

Cisco

Cisco CGR 1000 Series User manual

Cisco

Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs... Instruction Manual

Cisco

Cisco NCS 540 User manual

Cisco

Cisco o UCS X440p Installation and maintenance instructions

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Operator's manual

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... User manual

Cisco

Cisco OL-7822-06 User manual

Cisco

Cisco Cisco ASA Series User manual

Cisco

Cisco 2431 - IAD Router User manual

Cisco

Cisco ISA500 Series User manual

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet User manual

Cisco

Cisco Nexus 3000 series User manual

Cisco

Cisco ONS 15454 SDH Manual

Cisco

Cisco PRISMA II XD User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide