CHIEF MSP-SPCM User manual
Plasma Ceiling Mount
Model MSP-SPCM (PCM Series)
The MSP-SPCM, with Q-latch design, is a quick ceiling instal-
lation process that easily attaches to 1 1/2” NPT coupling. A
low profile design compliments the sleekness of you plasma
while providing versatile sturdy support for your plasma.
With the mount securely in place, simply install PSB-2095
(bracket designed specifically for your display) on your dis-
play, use the easy to hang Q-latches to mount your display, and
engage the locking device to prevent removal of the display.
Height adjustment (5”) and roll adjustment (4º right and left)
simplify screen positioning, Optimum viewing is easily
achieved using the tilt adjustment (15º down and 5º up).
The display can be installed using either the horizontal
(landscape) or vertical (portrait) mounting format.
BEFORE YOU BEGIN
•CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, and to the equipment
that will be attached to it, thoroughly study all instructions and illustrations before you begin the installation.
Pay particular attention to the “Important Warnings and Cautions” on Page 2.
• The maximum weight to be installed on the wall mount is 175 pounds (79.38 kg).
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
INSTALLATION INSTRUCTIONS
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
PART NO. 8832-000098 (Rev. A)
©2005 Chief Manufacturing
www.chiefmfg.com
08/05
2
Installation Instructions MSP-SPCM
IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-
sponding instructions.
•WARNING: Improper installation can result in serious personal injury! Make sure that the ceiling structural mem-
bers can support a redundant weight factor five times the total weight of the equipment. If not, reinforce
the ceiling before installing the suspended ceiling kit.
•WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
•WARNING: The installer is responsible for verifying that the ceiling to which the reinforcing plate on the mount is
anchored will safely support the combined load of all attached components or other equipment.
•WARNING: The combined weight of the plasma display panel must not exceed 175 lbs (79.38 kg), the maximum load
capacity of the reinforcing plate.
•CAUTION: Check the unit for shipping damage before you begin the installation.
DIMENSIONAL DRAWING
35 1/16”
To
40 1/16”
27 1/16”
To
32 1/16”
5” Height
Adjustment
Tilt
25 Degrees Down
5 Degrees Up
1 1/2” NPT
Installation Instructions MSP-SPCM
3
C O N T E N T S
IMPORTANT WARNINGS AND CAUTIONS ................. 2
DIMENSIONAL DRAWING .............................................. 2
TOOLS REQUIRED FOR INSTALLATION ..................... 3
PARTS LIST ........................................................................ 3
PARTS.................................................................................. 4
ASSEMBLY PROCEDURE ................................................ 4
INSTALL PSB-2095 ............................................................ 5
MOUNTING PROCEDURES ............................................. 7
ADJUSTMENTS.................................................................. 8
TOOLS REQUIRED FOR
INSTALLATION
• Pipe wrench
• 5/16” Allen Wrench
• 1/2” wrench
• Other tools may be required depending on the method of
installing the unit in the ceiling.
PARTS LIST
Unpack the carton and verify the contents listed in Table 1 on
page 3. If you are missing any of the listed parts, contact
Customer Service at: 1-800-582-6480.
Table 1: Parts List
REF DESCRIPTION QTY
1 Screw, Cap, Button Head 8
2 Nut, Hex, 3/8-16 2
3 Washer, Stainless Steel 2
4Nut,Lock,10-24 1
5 Washer, UHMW 3
6Plate,Front 1
7 Knob, Latch 1
8 Tube, 1 1/2” Threaded 1
9 Mount, Pitch 1
10 Adapter, Mount, Pitch 1
11 Buckle, Spud 2
12 Screw, Socket Head Cap, 1/4-20 2
13 Key, Allen (Not Shown) 1
14 Washer, Flat 2
15 Screw, Pan Head, 10-24 1
16 Spacer, .38 X .194 X .032” 1
4
Installation Instructions MSP-SPCM
PARTS
1
3
9
8
2
10
45
7
6
11 12
14
15
16
ASSEMBLY PROCEDURE
1. Remove two adjustment screws that are not securing the
tube and open the body assembly by raising the tube, piv-
oting it on the tilt adjustment screws (see Figure 1).
2. Secure the tube using the two adjustment screws removed
in step 1.
3. Using four 5/16-18 button head cap screws and four wash-
ers, secure the body to the plate assembly (see Figure 2).
Tilt Adj. Screw
Remove and
Reinstall Here
after tube is raised
Body Assembly Plate Assembly
Figure 1. Raise tube of Body
Figure 2. Assemble Body to Plate
Installation Instructions MSP-SPCM
5
INSTALL PSB-2095
The PSB-2095 parts list is shown in the table on this page.
1. Using a 10-24 button head cap screw inserted from the
backside of the bracket (see Figure 3), secure the mount-
ing button with the chamfered hole of mounting button
(larger surface) facing the bracket (see Figure 4).
2. Repeat Step 1 to install the other three mounting buttons.
REF DESCRIPTION QTY
10 Plasma Bracket 1
20 10-24 x 1/2 Button Head Cap Screw 4
30 M5 x 20mm Button Head Cap Screw 4
40 M6 x 20mm Button Head Cap Screw 4
50 Mounting Buttons – Tapped 4
60 1/8” Allen Key 1
70 .875 OD x .33 ID x .375 Nylon Spacer 4
80 M4 Allen Key 1
Mounting Button
10-24 Button Head
Cap Screw
Attach Mounting Buttons
Using These Holes
Figure 3. Mounting Button Attachment
Figure 4. Mounting Button Location
6
Installation Instructions MSP-SPCM
INSTALL PSB-2095 (CONT’D)
3. Place nylon spacers over the mounting holes on the back
of the screen (see Figure 5).
4. Attach mounting bracket to the display (see Figure 6), as
follows:
a. For 32” screens, use the M5 screws.
b. For 42” and 50” screens, use the M6 screws.
Nylon Spacer
6mm
6m
m
50” Display
42” Display
32” Display
5mm
Nylon Spacer
Figure 5. Bracket Hole Location
Figure 6. Bracket Attachment Location
50” Display
42” Display
32” Display
Installation Instructions MSP-SPCM
7
MOUNTING PROCEDURES
1. Thread the mount onto the 1 1/2”NPT pipe extension/cou-
pling you have provided.
2. Read and follow the hanging bracket instructions
(PSB-2095) for your application (display model).
3. Make sure the mount is level (see “ADJUSTMENTS” on
page 8, Roll) and latch is positioned so it will not obstruct
plasma installation (see Figure 7).
4. With one person supporting each side of the display, align
the four Q-latches with the four openings.
5. Secure the display by completely engaging the latch.
6. Lock the display in place by installing a Q-clamp on each
side of the bottom of face plate as shown in Figure 8.
7. Connect and secure power/audio/video cables.
Q-latch
PSB-2095
Latch
to
secure
your
display
Figure 7. Mounting
Q-Latch Q-Clamp
Figure 8. Install Q-Locks
8
Installation Instructions MSP-SPCM
ADJUSTMENTS
Height
1. Loosen four 5/16-18 button head cap screws (see
Figure 9).
2. Adjust the height to the desired position.
3. Tighten the four 5/16-18 button head cap screws.
Roll
1. Loosen the two 3/8-16 Nylock nuts (see Figure 10).
2. Adjust the roll, using the slotted bottom holes, to the
desired position.
3. Tighten the two 3/8-16 Nylock nuts.
Tilt
1. Loosen the four 5/16-18 button head cap screws (see
Figure 11).
2. Adjust to the desired tilt position.
3. Tighten the four 5/16-18 button head cap screws.
Height
Adjustment
Screws
Nylock
Nuts
Figure 9. Height Adjustment
Figure 10. Roll Adjustment
Screws
Tilt
Adjustment
Figure 11. Tilt Adjustment
Table of contents
Other CHIEF Rack & Stand manuals
CHIEF
CHIEF PAC260D User manual
CHIEF
CHIEF Direct Attach Ceiling Mount JHS Series User manual
CHIEF
CHIEF MSP-WRTS1 User manual
CHIEF
CHIEF PAC230 User manual
CHIEF
CHIEF MF2 Series User manual
CHIEF
CHIEF OLCB1U User manual
CHIEF
CHIEF PAC-251 User manual
CHIEF
CHIEF PDC Series User manual
CHIEF
CHIEF RGTU-210 User manual
CHIEF
CHIEF FSA-1005 User manual
CHIEF
CHIEF POTR-XL User manual
CHIEF
CHIEF RMT1 User manual
CHIEF
CHIEF PAC-710 User manual
CHIEF
CHIEF FSA-1002 User manual
CHIEF
CHIEF RPME Elite Series User manual
CHIEF
CHIEF MFAUBSP User manual
CHIEF
CHIEF K1C1KRA204 User manual
CHIEF
CHIEF CSMP9X12 User manual
CHIEF
CHIEF KTP220 User manual
CHIEF
CHIEF PACCS1 User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
