CHIEF MAGNA-VIEW User manual

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

12800 HIGHWAY 13 SOUTH, SUITE 500

SAVAGE, MINNESOTA 55378 USA

CONTROLLER BOARD BOX

TERMINAL FUNCTION DEFINITIONS

TERMINAL

NUMBER FUNCTION DESCRIPTION WIRING OPTIONS NOTES

124 VOLT AC 24 volt AC output

224 VOLT AC

COMMON 24 volt AC common

This is an internal power

supply for powering external

devices & Remote

Controllers.

Chief Mfg. offers the RC-10

Radio Frequency Remote

Controller which runs off of

this power supply.

3GROUND Ground

412 VOLT DC 12 volt DC

This is an internal power

supply for powering external

devices &/or used for

initiating specific functions

(Extend/Retract 5 or Voltage

Sensor 7).

5EXTEND/

RETRACT

Initiates movement if lift is static, or

stops movement if lift is in motion.

Direction of travel will be opposite of

last direction of travel.

Function operates on

momentary switch only.

Operating range is 5 – 30

Volts AC or DC.

6EXTEND/

RETRACT

COMMON

Used in conjunction with

Extend/Retract when using an

external power source to initiate

movement.

To Operate using Internal Power

Source

Connect terminals 3 & 6 with

Jumper Wire. Connect Momentary

Switch to terminal 4. Connect

other line of Momentary Switch to

terminal 5.

To Operate using External Power

Source

Connect External Power Supply’s

Common to terminal 6. Connect

initiating signal to terminal 5.

NOT TO BE USED AS

GROUND FOR FUNCTION

OTHER THAN

EXTEND/RETRACT

TERMINAL 5.

7VOLTAGE

SENSOR

When terminal senses voltage, unit

will extend.

When terminal senses cessation of

voltage, unit will retract.

Operating range is 5 – 30

Volts AC or DC.

8VOLTAGE

SENSOR

COMMON

Used in conjunction with Voltage

Sensor when using an external power

source to initiate movement.

Voltage Sensing

Connect positive lead to terminal 7.

Connect Ground of switching

device to terminal 8.

Single-Pull/Throw Latching Switch

Connect terminals 3 & 8 with

Jumper Wire. Connect first Switch

Terminal to terminal 4.

Connect other Switch Terminal to

terminal 7.

NOT TO BE USED AS

GROUND FOR FUNCTION

OTHER THAN VOLTAGE

SENSOR TERMINAL 7.

9SERVICE

EXTEND

Extends unit to maximum limit,

bypassing normal-use travel setting.

Often used for servicing projectors in

ceiling lifts.

Momentary or Latching contact to

Ground terminals 3, 10, 13, or 20.

Feature not available on all

models.

If using Latching Switch, be

sure to disengage Switch prior

to initiating any other

function.

10 GROUND Ground

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 