CHIEF FDP Series User manual

8803-000033 01/26/04

CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: [email protected]

INSTALLATION INSTRUCTIONS

FDP SERIES

SMALL FLAT PANEL DISPLAY

DUAL SCREEN POLE MOUNT

Exclusive Q2™ Mounting System

Prior to assembly, unpack carton completely and verify contents.

If you are missing any of the following components, please contact Customer Service at 1-800/582-6480.

(2) FDP Pole-Mounting Bracket Half (2) ¼” Flat Washer

(2) ¼-20 X 4.25” Hex Bolt (8) 10-24 X 1.00 Thread Forming Screw

(8) ½” X ½” Nylon Spacer

BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY

The FSP will fit on any 1/1/2” to 2” O.D. pipe including 1 ½”NPT.

Flat Panel Displays are Extremely Fragile.

If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),

DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.

Interface Bracket Installation:

1. See installation procedures accompanying your mounting bracket.

Optional Latching Flag Placement:

1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).

2. Reposition latching flag and secure using Phillips head screw, Nylock nut.

Figure 1

Figure 2

CAUTION!

Remove screw

and nu

ove

atc

8803-000033 01/26/04

CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: [email protected]

Pole-Mounting Bracket Assembly and Installation:

1. Assemble two pole-mounting bracket halves as shown in Figure 3 and secure using two ¼-20 X 4.25”

hex bolts and two ¼” flat washers.

2. For vertical pole mounting, install the pole-mounting bracket on 1 ½” to 2” OD pipe/pole and secure

using 7/16” hex drives (see Figure 4).

3. For horizontal pole mounting; remove eight tilt adjustment screws, reposition the tilt bracket as

shown in Figure 5, and insert nylon spacers. Secure using 10-24 x 1.00 screws provided.

Mounting Display with Interface Bracket to Pole-Mounting Bracket:

1. Make sure both latching flags on pole-mounting bracket are in the unlocked position (see Figure 4).

2. Place your small flat panel displays; with interface brackets attached, onto the pole-mounting bracket,

making sure they are securely seated.

3. Engage pole-mounting bracket latching flags, locking small flat panel displays in place (see Figure 6).

4. Adjust tilt by loosening (slightly) tilt adjustment screws (see Figure 7) on each side of pole-mounting

bracket, adjust to desired angle, and tighten tilt adjustment screws.

Figure 3 Figure 4

Locked

Unlocked

Tighten to

secure to

ole

Tilt

Adjustment

Screws

Figure 6

10-24 x 1.00 screw

.500 O.D. x .500

long nylon spacer

Figure 7

¼-20 X 4.25” hex bolt

and ¼” washer

Figure 5

This manual suits for next models

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 