C.A. Technologies Jaguar 300H User manual

HVLP AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

AIR CAP

RING

AVAI LABLE FLUI D

NOZZLES TIPS

NEEDLES /

marking on needle

23-1008 40** 13.5 33-0208 0.8mm (.022") 40-1308 (308)

23-1010 40** 13.5 33-0210 1.0mm (.040") 40-1310 (310)

23-1012 40** 13.5 33-0212 1.2mm (.046") 40-1312 (312)

23-1013 40** 13.5 33-0213 1.3mm (.052") 40-1313 (313)

23-1014 40** 13.5 33-0214 1.4mm (.055") 40-1314 (314)

23-1015 40** 13.5 33-0215 1.5mm (.059") 40-1315 (315)

23-1017 40** 13.5 33-0217 1.7mm (.070") 40-1317 (317)

23-1019 40** 13.5 33-0219 1.9mm (.075") 40-1319 (319)

23-1022 40** 13.5 33-0222 2.2mm (.086") 40-1322 (322)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Note: Air cap test gages are available to confirm HVLP compliance.

*Gun inlet pressures may vary as required by application

**When using optional gun regulator, inlet pressure changes to 45psi

IncludedJ300H 60-1502 (#2)

GRAVITY FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Jaguar 300HJaguar 300H

Jaguar 300H

Operation and Maintenance Instructions for

J300HJ300H

J300H

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Screw the paint cup onto the gun’s gravity feed fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control

fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Remove air cap and clean separately using clean solvent.

Clean the gravity feed cup thoroughly, then spray clean solvent through the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Have repair kit # 10-105 available before gun disassembly.

Gun head disassembly

To remove the nozzle carrier (5) and air cap adapter (7):

1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (16).

2. Remove the needle seal cartridge (17).

3. Loosen the locknut (11) and remove fluid inlet (12) using a 11/16” open-end wrench.

4. The nozzle carrier (5) and air cap adapter (7) will now slide forward from the gun body (13).

Gun head reassembly

1. Install a new o-ring (4 & 8) on the air cap adapter (7).

2. Install the thread locknut (11) and seal (10) onto the fluid inlet (12) as far as possible.

3. Install a new fluid inlet seal (9) into the recess area on the nozzle carrier (5) inlet port.

4. Install carrier seal (6) onto the back of the nozzle carrier (5).

5. Slide the nozzle carrier (5) into air cap adapter (7) and insert into the gun body (13) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (17) but do not tighten.

6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (12) and tighten firmly.

7. Tighten the needle seal (17) to approx. 12 ft.-lb. torque.

8. Tighten the fluid inlet (12) to approx. 25 ft.-lb. torque.

9. Tighten the locknut (11) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPT ION IT EM NO. PART NO. DESCRIPT ION

1 See Air Cap Chart Air Cap** 19 60-2101 Trigger

2 See Air Cap Chart Fluid Tip** 20 60-1520 Air Valve Assembly

3 33-1201 Fluid Nozzle Body 21 60-302 Air Valve Poppet

4 98-8026 O-Ring* 22 60-125 Seal*

5 60-J31H Nozzle Body Carrier 23 61-1003 Air Valve Spring*

6 60-123 Seal* 24 60-119 Seal*

7 60-34H Air Cap Adapter 25 60-201 Rear Bushing

8 60-131 O-Ring* 26 60-204 Needle Return Spring*

9 60-124 Seal* 27 60-205 Spring Seat*

10 60-130 Seal* 28 60-202 Fluid Control Knob*

11 60-118 Locknut 29 60-1510 Inlet Air Control (Optional)

12 60-127 Fluid Inlet 30 60-122 Plug

13 60-1113 Jaguar Gun Body HVLP 31 60-104 Air Inlet Fitting

14 98-0109 Allen Plug 51-401 Standard 700 mL Gravity Feed Cup (Aluminum)

15 See Air Cap Chart Fan Control Assembly** 51-400 Optional 700 mL Gravity Feed Cup (Plastic)

16 See Air Cap Chart Fluid Needle** 51-403 Optional 1000 mL Gravity Feed Cup (Aluminum)

17 60-1400 Needle Seal* 51-418 Gravity Cup Lid (401 & 403)

18 60-1033 Trigger Pivot Set 51-413 Gravity Cup Lid (400)

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-105

HVLP AIR CAP TEST GAGES

23-1008-G

23-1010-G

23-1012-G

FOR

J300H

GUNS

23-1013-G

23-1014-G

23-1015-G

23-1022-G

23-1017-G

23-1019-G

J300H HVLP SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AI R C AP

MAXIMUM

PATTERN WIDTH CFM

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.5 mm x 1015

1.7 mm x 1017

1.9 mm x 1019

2.2 mm x 1022

13.5

FLUID NOZZLE / AIR CAP SELECTION CHARTS

JAGUAR Series 300H - Gravity Feed Guns

1.0 mm x 1010 12 13.5

1.0 mm x 1010

1.3 mm x 1013

13.5

1.3 mm x 1013

1.5 mm x 1015

1.7 mm x 1017

13.5

Revised 3/18/14

Other C.A. Technologies Paint Sprayer manuals

C.A. Technologies

C.A. Technologies Jaguar 300 Series User manual

C.A. Technologies

C.A. Technologies Panther 200C User manual

C.A. Technologies

C.A. Technologies CPR User manual

C.A. Technologies

C.A. Technologies FE-Line Fine Finish User manual

C.A. Technologies

C.A. Technologies H2O-CPR-G User manual

C.A. Technologies

C.A. Technologies H2O-CPR User manual

C.A. Technologies

C.A. Technologies Tomcat Series User manual

C.A. Technologies

C.A. Technologies FE-Line LCFM Troubleshooting guide

C.A. Technologies

C.A. Technologies Lynx 300C Troubleshooting guide

C.A. Technologies

C.A. Technologies CAT-Xpress Troubleshooting guide

C.A. Technologies

C.A. Technologies Lynx 200C User manual

C.A. Technologies

C.A. Technologies Tomahawk TG User manual

C.A. Technologies

C.A. Technologies Panther 200Z User manual

C.A. Technologies

C.A. Technologies Panther 100G 1590 User manual

C.A. Technologies

C.A. Technologies LYNX L100CM Manual

C.A. Technologies

C.A. Technologies AutoCAT 100C User manual

C.A. Technologies

C.A. Technologies Jaguar SLP User manual

C.A. Technologies

C.A. Technologies Lynx 100CVT User manual

C.A. Technologies

C.A. Technologies AutoCAT 300C User manual

C.A. Technologies

C.A. Technologies AutoCAT 100CVT User manual

C.A. Technologies

C.A. Technologies CPR User manual

C.A. Technologies

C.A. Technologies Techline JR User manual

C.A. Technologies

C.A. Technologies Lynx 100C User manual

C.A. Technologies

C.A. Technologies TOMCAT 100C Troubleshooting guide

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual