C.A. Technologies Tomcat Series User manual

CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS Press /

Siphon

*SUGGESTED

GUN INLET

PRESS.

FAN

CONTROL SCFM AIR CAP

RING

AVAI LABLE FLUI D

NOZZLES

NEEDLES /

marking on needle

21-2163 pressure 50 8

21-2263 pressure 50 14

21-2263-E pressure 50 15 31-0606 0.6mm (.022")

21-2363 pressure 50 13.6 31-0607 0.7mm (.028")

21-2166 siphon 50 5 31-0610 1.0mm (.040")

21-2266 siphon 50 12 31-0612 1.2mm (.046")

21-2266-3 pressure 50 16.2 31-0613 1.3mm (.052")

21-2366 siphon 50 12 31-0615 1.5mm (.059")

21-2466 siphon 50 15 31-0618 1.8mm (.070")

21-2167 pressure 50 14.5 31-0622 2.2mm (.086") 40-1122 (122)

21-2267 pressure 50 15 31-0628 2.8mm (.110") 40-1128 (128)

21-2168 pressure 50 14

21-200** pressure 50 5.2

21-201** pressure 50 5.2

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Gun inlet pressures may vary as required by application

**200 Air cap requires P/N 21-1583 base & 21-1584 ring

T100C 60-1500 Included

40-1107 (107)

40-1110 (110)

40-1115 (115)

omcat Seromcat Ser

omcat Seriesies

iesies

ies

PRESSURE/SIPHON FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies P.O. Box 17820, Boulder CO 80308 (888) 820-4498 Fax (303) 438-5708

www.sprayCAT.com

Operation and Maintenance Instructions for

TOMCAT

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It

is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine

tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the

manufactures instructions.

2. If a gun cleaner is not being used:

For pressure setups, remove air cap and clean separately using clean solvent.

Connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow thru the gun until clean.

For siphon setups, first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning

and maintenance.

Gun head disassembly and reassembly instructions:

Gun head disassembly

To remove the nozzle carrier (5) and air cap adapter (6):

1. Remove the air cap (1), fluid nozzle tip (2), head insert (3), and needle (9)

2. Remove the needle seal cartridge (21)

3. Loosen the locknut (20) and remove fluid inlet (19) using a 5/8” open-end wrench

Gun head reassembly

1. Install the thread locknut (9) onto the fluid inlet as far as possible.

2. Install the needle seal (21).

3. Install seal ring (4), then tighten the head insert (3) with 5/8” open-end wrench until snug. BEWARE - DO NOT OVER

TIGHTEN.

4. Install seal ring (4), then tighten the fluid inlet (19) to approx. 25 ft.-lb. torque.

5. Tighten the locknut (20) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION

1 See Air Cap Chart Air Cap 13 60-104 Air Inlet

2 See Air Cap Chart Fluid Nozzle Tip 14 60-122 Plug

3 60-15C Head Insert 15 60-1003 Air Valve Spring

4 60-137 Seal Ring - Fluid 16 60-125 Gasket

5 60-1106 Gun Handle 17 60-302 Air Valve Poppet

6 See Air Cap Chart Fan Control Assembly 18 60-1520 Air Valve Assembly

7 60-119 Seal 19 60-132 Fluid Inlet

8 60-0201 Rear Bushing 20 60-128 Locknut

9 See Air Cap Chart Needle 21 61-1026 Needle Seal Cartridge

10 60-204 Needle Return Spring 22 60-2101 Trigger

11 60-205 Spring Seat 23 61-1033 Trigger Pivot Set

12 60-202 Fluid Control Knob Repair Kit 10-112 Tomcat Repair Kit

*Indicates part included in repari kit # 10-112

T100C CONVENTIONAL SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP

MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.5, 1.8mm x 2466

2.2 mm x 2167

2.2 mm x 2267

2.8 mm x 2168

0.6, 0.7, 1.0 mm x 2163

0.6, 0.7, 1.0 mm x 2366

0.6, 0.7, 1.0 mm x 2466

1.2, 1.3, 1.5, 1.8 mm x 2263

1.2, 1.3, 1.5, 1.8 mm x 2266

1.2, 1.3, 1.5, 1.8 mm x 2266-3

1.2, 1.3, 1.5, 1.8 mm x 2466

FLUID NOZZLE / AIR CAP SELECTION CHARTS

TOMCAT SERIES - Pressure / Siphon Feed Guns

0.6, 0.7 mm x 2163

0.6, 0.7 mm x 2166

0.6, 0.7 mm x 2266

Revised 1/18/13

This manual suits for next models

Other C.A. Technologies Paint Sprayer manuals

C.A. Technologies

C.A. Technologies AutoCAT 100CVT User manual

C.A. Technologies

C.A. Technologies Lynx 100C User manual

C.A. Technologies

C.A. Technologies Jaguar 300 Series User manual

C.A. Technologies

C.A. Technologies Techline JR User manual

C.A. Technologies

C.A. Technologies Panther 200C User manual

C.A. Technologies

C.A. Technologies Lynx 300C Troubleshooting guide

C.A. Technologies

C.A. Technologies Cougar User manual

C.A. Technologies

C.A. Technologies Lynx 100C 1590 User manual

C.A. Technologies

C.A. Technologies Tomahawk TG User manual

C.A. Technologies

C.A. Technologies CPR User manual

C.A. Technologies

C.A. Technologies AutoCAT 300C User manual

C.A. Technologies

C.A. Technologies H2O-CPR-G User manual

C.A. Technologies

C.A. Technologies Lynx 300H User manual

C.A. Technologies

C.A. Technologies FE-Line Fine Finish User manual

C.A. Technologies

C.A. Technologies Jaguar SLP User manual

C.A. Technologies

C.A. Technologies Lynx 200C User manual

C.A. Technologies

C.A. Technologies Lynx 100H User manual

C.A. Technologies

C.A. Technologies Panther 100G User manual

C.A. Technologies

C.A. Technologies Lynx L100C User manual

C.A. Technologies

C.A. Technologies Panther 100G 1590 User manual

C.A. Technologies

C.A. Technologies JAGUAR SLP User manual

C.A. Technologies

C.A. Technologies Jaguar 300H User manual

C.A. Technologies

C.A. Technologies Jaguar 100 Series User manual

C.A. Technologies

C.A. Technologies Panther 200H User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual