Bosch ISC-FPB1-W60QS Operating instructions

Photobeam 5000

ISC-FPB1-W60QS, ISC-FPB1-W120QS, ISC-FPB1-W200QS

en Installation and Operation Guide

Table of contents

1Introduction 4

1.1 About documentation 4

1.2 Bosch Security Systems, Inc 4

2System overview 5

2.1 Features 5

2.2 Photobeam overview 6

2.3 Console overview 7

2.4 Transmitter/receiver dimensions 8

3Installation 9

3.1 Beam spread 9

3.2 Pole mount installation 10

3.3 Wall mount installation 12

4Wiring 13

4.1 Terminal strip overview 13

4.2 Wiring distance 14

4.3 Wiring routes 14

5Special features 16

5.1 Level LED 16

5.2 EDC (Environmental Discrimination Circuit) 16

5.3 Beam interruption time 17

5.4 Beam power control 17

6Setup 18

7Optical alignment 20

7.1 Level LED - alignment of the Upper Beam 20

7.2 Level LED - alignment of the Lower Beam 20

7.3 Volt meter alignment 21

8Operational check 22

9Troubleshooting 23

9.1 Additional information 23

10 Certifications 24

11 Specifications 25

Photobeam 5000 Table of Contents | en 3

Bosch Security Systems, Inc. Installation and Operation Guide 2016.02 | 03 | F.01U.305.910

Introduction

This document contains information that a trained installer needs to install the Photobeam

5000 quad-beam photoelectric detector contained inside the packaging.

About documentation

This document is the intellectual property of Bosch Security Systems, Inc. and is protected by

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

Bosch Security Systems, Inc

Use the serial number located on the product label and refer to the Bosch Security Systems,

Inc. website at http://www.boschsecurity.com/datecodes/.

Manufacturing date information is contained in digit no 1 – 3: DDD.

1.1

1.2

4en | Introduction Photobeam 5000

2016.02 | 03 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.

System overview

The ISC-FPB1-W60QS, ISC-FPB1-W120QS and ISC-FPB1-W200QS are quad-beam

photoelectric detectors designed for indoor and outdoor applications. Consisting of a

separate transmitter and receiver, an alarm is activated when a person passes through all four

beams. Combination of features and adjustable parameters allow for better catch

performance, lower false alarm rates and reduced effects of environmental disturbances.

Features

For stable operation, the detectors are equipped with the following feautres:

100% Sensitivity Allowance

Maintains stable operation even if 99% of beam energy is cut, for example by rain, fog, frost,

and so on.

Quad Beam Detection

Fewer false alarms caused by birds and other small animals because all four beams must be

blocked simultaneously to cause an alarm.

Beam Power Control

Select the appropriate beam intensity relative to the detection range to minimize reflection on

nearby walls and cross-talk with other detectors.

Beam Interruption Time Control

Use to change the beam interruption time to best fit the application.

2.1

Photobeam 5000 System overview | en 5

Bosch Security Systems, Inc. Installation and Operation Guide 2016.02 | 03 | F.01U.305.910

Photobeam overview

Figure 2.1: Photobeam components overview

Callout ー Description Callout ー Description

1 ー Mounting holes 8 ー Optical alignment

2 ー Mounting plate 9 ー Vertical adjustment

3 ー Device securing screws 10 ー Horizontal adjustment

4 ー Wire entry 11 ー Console

5 ー Wiring terminals 12 ー Cover

6 ー Detector 13 ー Cover securing screws

7 ー Optical module

2.2

6en | System overview Photobeam 5000

2016.02 | 03 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.

Console overview

Figure 2.2: Console components overview

Callout ー Description Callout ー Description

1 ー Transmitter console 5 ーReceiver console

2 ー Power Indicator 6 ー Status Indicators

3 ー Function switches 7 ーSensitivity control

4 ー Beam Power Control 8 ーAlignment check terminals

2.3

Photobeam 5000 System overview | en 7

Bosch Security Systems, Inc. Installation and Operation Guide 2016.02 | 03 | F.01U.305.910

Transmitter/receiver dimensions

103 mm (4.0 in)

19.3 mm

(0.75 in)

398 mm (15.66 in)

244 mm (9.60 in)

96 mm (3.77 in)

77.1 mm

(3.03 in)

337.7 mm (13.29 in)

56 mm

(2.20 in)

220 mm (8.66 in)

39 mm

(1.5 in)

39.7 mm

(1.56 in)

Figure 2.3: Transmitter/receiver dimensions

Callout ﹘ Description Callout ﹘ Description

1 ー Knockout wire entrance 3 ー Center of the Upper Beam

2 ー Center of the Lower Beam 4 ー Wire entrance

2.4

8en | System overview Photobeam 5000

2016.02 | 03 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.

Installation

Prior to installing the devices, please review the installation considerations below:

– Install in an area that is clear of objects

– Install the transmitter/receiver within the maximum protection range of the model

– Do not install:

– Receivers into intense sources of light (for example, rising and setting sun)

– On movable surfaces subject to vibrations

– Detectors where immersion to water, corrosive liquids, or exposure to high levels of

dust can occur

– Detectors in close proximity to strong electromagnetic noises

– Do not use detectors with other photobeam detectors or receivers

– Do not stack detectors

– Do not disassemble or modify this detector

– Do not install while the power is on

– Avoid extreme temperature and humidity ranges as defined in the products specifications

– Avoid installing detectors near magnets and/or magnetized materials

– Avoid beam interference between other units when multiple units are installed.

Beam spread

The beam spread angle is ±0.7 °from the transmitter to the receiver. Refer to the diagram and

table below to determine the installation conditions.

Figure 3.1: Beam distance and spread

Callout ﹘ Description Callout ﹘ Description

1 ー Transmitter 4 ー Receiver

2 ー Horizontal spread (B) 5 ー Distance (A)

3 ー Vertical spread (C)

3.1

Photobeam 5000 Installation | en 9

Bosch Security Systems, Inc. Installation and Operation Guide 2016.02 | 03 | F.01U.305.910

Distance, horizontal and vertical spread values: (A) / (B) / (C)

Metric Imperial unit

20 m / 0.5 m / 0.8 m 65 ft / 1.6 ft / 2.6 ft

40 m / 1.0 m /1.3 m 13.1 ft / 3.2 ft / 4.2 ft

60 m / 1.5m / 1.8 m 196 ft / 4.9 ft / 5.9 ft

80 m / 2.0 m / 2.2 m 262 ft / 6.5 ft / 7.2 ft

100 m / 2.5 m / 2.7 m 328 ft / 8.2 ft / 8.8 ft

120 m / 3.0 m / 3.2 m 393 ft / 9.8 ft / 10.4 ft

140 m / 3.5 m / 3.7 m 459 ft / 11.4 ft / 12.1 ft

160 m / 4.0 m / 4.2 m 524 ft / 13.1 ft / 13.7 ft

180 m / 4.5 m / 4.7 m 590 ft / 14.7 ft / 15.4 ft

200 m / 5.0 m / 5.2 m 656 ft / 16.4 ft / 17.0 ft

Pole mount installation

Figure 3.2: Pole mounting view

Callout ﹘ Description Callout ﹘ Description

1 ー Diameter 38.0 – 42.7 mm (1.50 – 1.68

in)

2 ー Back-to-back pole mounting

Attaching the mounting bracket:

1. Choose an appropriate mounting location for the devices. Install the mounting poles with

a clear line-of-sight between the transmitter and receiver.

2. Loosen the transmitter’s cover mounting screw and remove the cover.

3. Loosen the two base mounting screws and remove the mounting plate by sliding it down.

4. Attach the mounting hardware to the mounting plate using the clamping screws. Refer to

the figure below.

3.2

10 en | Installation Photobeam 5000

2016.02 | 03 | F.01U.305.910 Installation and Operation Guide Bosch Security Systems, Inc.

This manual suits for next models

Table of contents

Other Bosch Security System manuals

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual