Bosch IUI-BES-AO User manual

BES External Signaling Devices

IUI-BES-AO, IUI-BES-A

en Installation Manual

Table of contents

1Safety 4

2Short information 5

3System overview 6

4Installation 7

5Connection 8

6Technical data 12

BES External Signaling Devices Table of Contents | en 3

Bosch Sicherheitssysteme GmbH Installation Manual 2017.07 | 04 | F.01U.318.493

Safety

Danger!

Electricity

Injuries due to electricity are possible.

Switch off all electricity while installing the product.

Do not open or modify this product, except if described in this manual.

Danger!

Electricity

Injuries and damage of the system due to wrong polarity and short circuits are possible.

When connecting wires and cables, ensure to use the correct polarity.

Danger!

Loud noise and flashing light

In case of wrong connections it is possible that the audio and visual signals are triggered

which leads to loud noises and flashing lights.

Switch off all electricity while installing the product.

Ensure to connect wires and cables according to this manual.

Ensure to have a safe stance and secure yourself appropriately when installing this product in

high places.

Be prepared for loud noises and flashing lights.

Old electrical and electronic appliances

Electrical or electronic devices that are no longer serviceable must be collected separately and

sent for environmentally compatible recycling (in accordance with the European Waste

Electrical and Electronic Equipment Directive).

To dispose of old electrical or electronic devices, you should use the return and collection

systems put in place in the country concerned.

4en | Safety BES External Signaling Devices

2017.07 | 04 | F.01U.318.493 Installation Manual Bosch Sicherheitssysteme GmbH

Short information

This manual describes the installation and connection of the BES external signaling devices.

It applies only to the following products:

– IUI-BES-AO, sold as of 12/2015

– IUI-BES-A, sold as of 07/2017

BES External Signaling Devices Short information | en 5

Bosch Sicherheitssysteme GmbH Installation Manual 2017.07 | 04 | F.01U.318.493

System overview

Figure 3.1: System overview

Element Description

1 Connectors

2 Wall-mounting bracket

3 Threaded bolt, only accessible from the right

4 Snap-in latches

5 Holes for black screws

6en | System overview BES External Signaling Devices

2017.07 | 04 | F.01U.318.493 Installation Manual Bosch Sicherheitssysteme GmbH

Installation

– The signaling device must be mounted vertical, with the LED lamps always at the top and

the speaker always at the bottom (for water drainage).

– In case of difficult installation conditions (for example walls with full thermal insulation or

roughcast plaster), an adapter module must be used.

– When mounting, clearance (to roof overhang) of at least 350 mm for IUI-BES-AO and of at

least 280 mm for IUI-BES-A must be allowed for.

Opening the housing

Notice!

The signaling device contains a tamper contact including a threaded bolt that delays the

opening of the housing to ensure to trigger the acoustic signal in case of tampering.

1. Push in the snap-in latches on both sides.

2. Push up the housing as far as possible.

3. Turn the threaded bolt to the left to unscrew and adjust it.

4. Lift off the housing completely.

Mounting the signaling device on flat surfaces

1. Mount the wall-mounting bracket onto the wall with four appropriate screws (not

included). If you are using an optional wall tamper, mount the wall-mounting bracket

directly on top of it.

Notice!

Suspension hook

After the wall-mounting bracket is mounted, the enclosed suspension hook can be used to

store the housing while working on the connections with both hands free.

Therefore insert the suspension hook into the hole at the bottom of the wall-mounting

bracket and thread the other end of the suspension hook through one of the holes designated

for the snap-in latches on the sides of the housing.

2. Connect the cables to connector A (wall-mounting bracket). The terminal resistors (12k1)

are already fitted to connector B (electrical module). If required, the correct resistors

must be fitted depending on the type of control panel.

3. Optionally connect the wall tamper.

4. Lift the housing on the wall-mounting bracket as far as possible.

5. Adjust the threaded bolt by screwing on the right.

6. Push down the housing completely.

7. Glue a seal in place over the right-hand snap-in latch.

8. In case of a VdS-compliant installation: Screw the black screws on both sides of the snap-

in latches.

BES External Signaling Devices Installation | en 7

Bosch Sicherheitssysteme GmbH Installation Manual 2017.07 | 04 | F.01U.318.493

Connection

Prefitted connections of connector B (built into the housing)

6 5 4 3 2 1

RERE

Element Description

1 Electrical module

2 Connector B

3 Terminal resistors

The terminal resistors depend on the security system (12k1 prefitted).

Connection of the system to connector A on the wall-mounting bracket (without using an

optional wall tamper)

A B1 B2 B3 A AB

3 4

8en | Connection BES External Signaling Devices

2017.07 | 04 | F.01U.318.493 Installation Manual Bosch Sicherheitssysteme GmbH

Element Description

1 Wall-mounting bracket

2 Connector A

3 Acoustic input

4 Visual input

4If you are using a long cable with a resistance higher than 9 ohm, use B2 instead of B1.

Changing the connection of the system to connector A when using a wall tamper

A B1 B2 B3 A AB

Element Description

1 Wall-mounting bracket

2 Connector A

3 Wall tamper

4 Acoustic input

5 Visual input

4If you are using a long cable with a resistance higher than 9 ohm, use B2 instead of B1.

BES External Signaling Devices Connection | en 9

Bosch Sicherheitssysteme GmbH Installation Manual 2017.07 | 04 | F.01U.318.493

Wiring of the system to connector A on the wall-mounting bracket (class C) for IUI-BES-AO

IUI-BES-AO

6 5 4 3

RERE

0 V

V+

0 V

Element Description

1 Security system

2 System-depending output voltage

3 Acoustic control

4 Optical control

5 Terminal resistors

The terminal resistors depend on the security system (12k1 prefitted).

4If you are using a long cable with a resistance higher than 9 ohm, use B2 instead of B1.

Wiring of the system to connector A on the wall-mounting bracket (class C) for IUI-BES-A

IUI-BES-A

6 5 4 3

RERE

0 V

V+

0 V

Element Description

1 Security system

2 System-depending output voltage

3 Acoustic control

4 Terminal resistors

The terminal resistors depend on the security system (12k1 prefitted).

10 en | Connection BES External Signaling Devices

2017.07 | 04 | F.01U.318.493 Installation Manual Bosch Sicherheitssysteme GmbH

This manual suits for next models

Table of contents

Other Bosch Security System manuals

Bosch

Bosch Solution 144 User manual

Bosch

Bosch ICP-VR8488 User manual

Bosch

Bosch B926F User manual

Bosch

Bosch DB24C4200R2 User manual

Bosch

Bosch Security System User manual

Bosch

Bosch VSS7915/00T User manual

Bosch

Bosch Solution 64 User manual

Bosch

Bosch ND 200 LSN User manual

Bosch

Bosch Security System User manual

Bosch

Bosch Solution 2000 Owner's manual

Bosch

Bosch PAVIRO Mounting instructions

Bosch

Bosch SM120RW User manual

Bosch

Bosch Solution 16i User manual

Bosch

Bosch IRIS-Net User manual

Bosch

Bosch D623 Series User manual

Bosch

Bosch DIVAR DIP-6080-00N User manual

Bosch

Bosch ODU-FA Instruction Manual

Bosch

Bosch DS860 Series User manual

Bosch

Bosch Security Escort SE2000 Series Installation guide

Bosch

Bosch MAP 5000 Series User manual

Bosch

Bosch ISW-BMC1-S135X User manual

Bosch

Bosch BRS User manual

Bosch

Bosch AMAX 2100 User manual

Bosch

Bosch ICP-AMAX4-P2-EN User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual