Bosch AMC UL1 User manual

AMC UL1 Housing | en 1

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

Included Parts

The metal housing inlcudes the following components:

Figure 1 Parts of the housing

The accessories kit includes the following cables. Install these

cables as described in Section Connection of the Devices,

page 4.

2en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

Figure 2 Accessories kit content

Content of the accessories kit:

A= Pre-assembled cable to connect the AMC to the power sup-

ply

B= Pre-assembled cable to connect the batteries to the UPS

(uninterruptable power supply) which is included in the power

supply

C= Cable using 24 V mode

D= Grounding cable for the cover

E= Cable ties to secure the pre-assembled cable

G= Pre-assembled cable with temperature sensor

H= Three screw anchors S8 and wood screws M6 x 50

J= Bracket for cable fixing

AMC UL1 Housing | en 3

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

Mounting the Housing

Open the housing cover lock with the provided key and remove

the hood from the wall mounted frame.

Mount the metal housing at the desired position with the screw

anchors provided with the enclosure.

Use the screws (position Hof the accessories kit) at the points

to mount the housing against the wall.

Figure 3 Demensions of the housing

4en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

Connection of the Devices

Figure 4 Connection of the devices

AMC UL1 Housing | en 5

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

1. Mount the AMC on the rail (item 2in Figure 1) and left

aside the power supply.

2. Put the batteries on the bottom of the housing and secure

them beneath the battery clips (item 7 in Figure 1).

3. Stick the bracket J (Figure 2) on the back of the housing in

such a way that later on not used connectors of the cable

Bcan fixed with it.

4. Cable set A:

a. Connect the 7-pin plug A1 to the AMC’s power supply

connector (labeled: POWER).

b. Attach connectors A3 to the PS-interface DC and A2

to the interface labeled OK.

c. Connect the grounding cable A4 beneath the ground-

ing point 3.

5. Cable set B:

a. Connect the plug connector B1 the second position

from the left on the power supply - labeled with BAT.

b. Attach connector B2b (red) to the +-pin of the first

battery.

c. With cable Cconnect the --pin of the first battery to

the +-pin of the second battery.

d. Attach connector B2a (black) to the --pin of the sec-

ond battery.

e. Connectors B3a and B3b are not used.

6. Cable set G:

a. Attach connector G1 on the PS-interface labbeled

RTH.

NOTE!

The following steps describe connecting the batteries in 24 V

mode. For information on 12 V mode connections, refer to

Section 12 V Mode Variations, page 7.

6en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

b. Route the cable across the temperature sensor

bracket 6so that the temperature sensor G2 hangs

approximitely 5 cm (2 in.) above the batteries.

7. Pre-assembled cable set 12:

a. Connect the 2-pin plug 13 on the interface AC of the

power supply.

8. Pre-assembled cable 5:

a. Connect the loose ends of the cover tamper switch to

the 2-pin screw connector on the top of the AMC.

Position the cable in the space between the housing

and the mounting rail.

9. Connect the main AC supply X:

a. Connect the brown (phase) wire to terminal L1.

b. Connect the blue (neutral) wire to terminal N.

c. Connect the grounding cable to the housing at posi-

tion 11.

DANGER!

Remove the fuse from the three-pin connector 12 before pro-

ceeding with the power supply connection.

Do not install the fuse before completing the installation proce-

dure.

CAUTION!

Shorten the external supply wires so that the ground (yellow/

green) wire is at least 20 mm (0.8 in.) longer than the live (blue

and brown) wires. This ensures that the ground wire cannot be

accidentally disconnected before life wires.

AMC UL1 Housing | en 7

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

10. Cable D:

If this cable is not pre-installed on grounding point 1, use

the cable Dfrom the accessories kit.

a. Connect D1 to grounding post 1.

b. Connect D2 to the grounding post on the cover.

11. Install the fuse.

12. Close the cover.

12 V Mode Variations

Figure 5.1 + 2 12 V mode with one and two batteries

NOTE!

Connect the readers and other peripheral devices as described

in the AMC Installation Manual (P/N: F01U.028.713). Route the

device cables through the knock-outs in the top an right side

wall of the housing, or through the rear of the housing.

8en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

The 12 V mode can be configured using one or two batteries.

For a one-battery installation, refer to Figure 5.1, and perform

the following procedure:

1. Connect B1 to the power supply position labbeled BAT.

2. Connect B2a (black) to the battery’s -terminal, and B2b

(red) to the battery’s +terminal.

3. Connectors B3a and B3b remain unused - fix them with the

bracket J.

For the two-battery installation, refer to Figure 5.2, and perform

the following procedure:

1. Connect B1 to the power supply position labbeled BAT.

2. Connect B2a (black) to the battery’s - terminal, and B2b

(red) to the battery’s +terminal.

3. Connect B3a (black) to the second battery’s -terminal,

and B3b (red) to the second battery’s +terminal.

NOTE!

To switch the power supply between 12 V or 24 V modes, dis-

connect the input voltage and set the switch as shown in the

figure below.

Table of contents

Other Bosch Security System manuals

Bosch

Bosch LTC 8850 Series User manual

Bosch

Bosch Solution 16i User manual

Bosch

Bosch MBV-BPRO-45 Instruction sheet

Bosch

Bosch ISN-SM-30 User guide

Bosch

Bosch ISW-BHB1-WX Service manual

Bosch

Bosch Security Escort SE2000 Series Installation guide

Bosch

Bosch MAP 5000 Series User manual

Bosch

Bosch LBB 1968 User manual

Bosch

Bosch AMAX 2100 User manual

Bosch

Bosch Radion B810 User manual

Bosch

Bosch CM705B How to use

Bosch

Bosch ISW-BMC1-M82X User manual

Bosch

Bosch Spexor User manual

Bosch

Bosch RF1100 User manual

Bosch

Bosch SE 320 LSNi User manual

Bosch

Bosch LTC 2682/90 Series User manual

Bosch

Bosch FMC-300RW-GSRRD User manual

Bosch

Bosch DB18C3100R2 User manual

Bosch

Bosch FK 100 LSN User manual

Bosch

Bosch LTC 8016/90 User manual

Bosch

Bosch PRAESENSA PRA-SCL Instruction sheet

Bosch

Bosch PAVIRO Mounting instructions

Bosch

Bosch B4512 User manual

Bosch

Bosch D9000 Series Configuration guide

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual