Avery Dennison Monarch 9485 User guide
System Administrator Manual
TC9485SA Rev. AB 7/12
1
Table of Contents
1. INTRODUCTION
3
1-1 Using This Manual 3
1-2 Using the Menu Chart 3
1-3 Using the Display and Buttons 4
1-3-1 Selecting a Menu 5
1-3-2 Exiting a Menu 5
1-3-3 Printing 5
1-4. Selecting a Language 6
2. USING DIAGNOSTICS
7
2-1 Diagnostics 7
2-1-1 Printer 8
2-1-2 Display 14
2-1-3 Buttons 15
2-1-4 RAM 16
2-1-5 Data Dump 17
2-1-6 About 18
3. SETTING UP THE PRINTER
19
3-1 SETUP 19
3-1-1 Stock PWR 20
3-1-2 Backlight 21
3-1-3 Contrast 22
3-1-4 Printer 23
3-1-5 Serial Communications 35
3-1-6 Power Management 39
23
1. INTRODUCTION
1-1. Using This Manual
1-2. Using the Menu Chart
Subjects Contents
1Introduction Notes before using printer
2Diagnostics How to print test label, check sensor, check print position, etc.
3Setting Up the Printer How to use the Setting Menu to adjust stock
and printer settings
The black boxes show present position, the boxes with a thick line show how you got there.
4.
Wi-Fi 41
4-1 RF Network 41
4-2 Using the Wi-Fi Settings Dialog 50
4-3 Using the Web Interface 52
4-4 Wi-Fi Glossary 82
4-5 Wi-Fi specications 87
5.
Bluetooth 88
5-1 Using the Bluetooth Settings Dialog 88
5-2 Bluetooth Interface 91
45
1-3. Using the Display and Buttons
1. Press Enter( ) button to enter the Menu
2. Move cursor to the menu using Up(▲) / Down(▼) buttons, and select the Menu by
pressing Enter( ) button.
Select Exit Menu or press the power ( )button to return to the previous menu
.
There are three ways to print.
1. When turning on the printer, press and hold the power ( ) button and the Down(▼)
button. The printer prints a batch (if sent) or prints the printer status information.
2. Select a test label from the Diagnostics menu.
3. Send batch data to the printer.
NOTE
button operates as feed button in ready condition only.
Screen displays Meaning
Selects the highlighted option.
Moves position of Menu upwards by one step.
Moves position of Menu downwards by one step
Moves the cursor to the position to change.
Increases set value
Decreases set value
Returns to higher Menu without saving the setting
Returns to higher Menu after saving the setting
1-3-1. Selecting a Menu
1-3-2. Exiting a Menu
1-3-3. Printing
Display
Enter button
Power button
Up button
Paper Feed /
Down button
▶
+
-
X
Y
FEED
▼
▲
67
1-4. Selecting a Language
2-1. Diagnostics
You can read Menu names or messages of the printer in English, French,
Spanish, German.
This chapter describes how to use Diagnostics in the Tool Box.
You can view test results through this Menu; however, you cannot change the setting.
1. Turn on the printer. The printer name and software version information are displayed.
Then you see
1. Turn on the printer. The printer name and software version information are displayed.
Then you see
2. Press Enter( ) button and then you see
3. Enter( ) button and you see
5. If correct password is typed in then you see
4. Press Up(▲) and Enter( ) button in the sequence of ,▲, ▲, ▲,
6. Cursor is positioned on the Diagnostics Menu. Enter into Diagnostics Menu by pressing
Enter( ) button.
2. Press Enter( ) button.
3. Move cursor to language by pressing Down(▼)button and then press Enter( ) button.
4. Move the cursor to the language you want by pressing Up(▲)/Down(▼) button then
press Enter( ) button.
5. The selected language is displayed on the screen.
6. Select exit to return to the diagnostics menu or press the power button to return to the
ready screen
2. Using Diagnostics
89
2-1-1. Printer
To return to initial screen, press power( )button
Four test labels can be printed: Diag Label, Test Pattern, Gray Scale,
MIF (Monarch Initialization Files) Info
**Test Label
1. Select Printer - Test Label - Diag Label in Diagnostics Menu
2. Select Printer – Test Label– Test Pattern in Diagnostics Menu
Checkerboard pattern is printed
Gray Scale printed
MIF Info printed
3. Select Printer - Test Label - Gray Scale in Diagnostics Menu.
4. Select Printer – Test Label – MIF Info in Diagnostics Menu.
Printer Diagnostics Labels are printed
10 11
In this Menu, you can read each A/D value of the Black Mark, Gap, or Peeler,
Peel-SW sensors. Position of each sensor is as shown in following picture.
**Sensors
1. Load stock in the printer.
2. Select Printer – Sensors – Black Mark in the Diagnostics Menu.
Check whether A/D value is changing in Black Mark sensor position while feeding
Black Mark stock manually.
3. Select Printer – Sensors – Peel in Diagnostics Menu. Check whether A/D value is
changing by covering the Peeler Sensor with stock
Make sure the stock is loaded in line with upper/lower Black Mark sensor.
PEELER SENSOR
B/M & GAP SENSOR
12 13
4. Select Printer – Sensors – Gap in Diagnostics Menu.
Check whether A/D value is changing in Gap sensor position by feeding Gap stock
manually.
5. Select Printer – Sensors – Gap in Diagnostics Menu.
Check whether A/D value is changing by Peeler S/W position.
1. Select Printer – Printhead – Temperat in the Diagnostics Menu.
1. You can check it in the battery shape located at upper right side of the ready screen.
In this Menu, You can check Printhead temperature(TPH) in ℃(Centigrade) unit.
The temperature of Printhead must be lower than 60℃ to print.
Press Enter( ) button to return to the previous menu.
**Printhead
There are two ways to check the battery level.
2. Select Printer – Battery in the Diagnostics Menu Battery level is displayed in
voltage on the screen
**Battery
NOTE
(7.8v above) (7.5v above)
(7.2v above) (6.8v below)
Press Enter( ) button to return to the previous menu.
1. Select Printer – View Total – Print Inch in Diagnostics Menu.
In this Menu, you can view Total inches printed
**View Total
Press Enter( ) button to return to the previous menu.
Remaining electricity of battery
Peel-SW
A/D Value = 194
With a roll of stock installed, slide the
peeler body towards the back of the printer.
Lift the peeler wing and slide the peeler body
towards the front of the printer.
6. Press Enter( ) button to return to the previous menu.
14 15
2-1-2. Display 2-1-3. Buttons
1. Select Display – Backlight in the Diagnostics Menu
You can check the display in this Menu.
1. Select Keyboard in Diagnostics Menu.
2. Press the upper left Up(▲) button, press the Down(▼) button, and press Enter( ) button.
3. Each should change from O shape to X shape when pressed.
4. Press Enter( ) button to from keyboard test.
2. Press the Up(▲) button Backlight is turned off, if the same button is pressed once more then it
is turned on.
3. Press Enter( ) button to exit from Backlight Test.
4. Select Display – Pixel in the Diagnostics Menu.
5. Press the Up(▲) button all Pixels on the screen are changed into black color and if it is
pressed once more then all Pixels are changed into white color.
6. Press Enter( ) button to exit from Pixel Test.
16 17
2-1-4. RAM 2-1-5. Data Dump
Select this Menu and check memory of the printer. Use this menu if you are having problems with a data stream. Data Dump captures the
data from the communications port and prints that information to a label.
1. Select RAM in Diagnostics Menu.
2. The message of RAM test running is displayed
For CPCL, previous command data printed on the paper
For MPCL, previous command data printed on the paper
1. Select Data Dump in Diagnostics Menu.
2. The labels print with data from the communication port.
3. If RAM test result is okay, then you see:
4. If RAM test result is not okay, then you see:
5. Press Enter( ) button to return to the previous menu.
Other manuals for Monarch 9485
2
Table of contents
Other Avery Dennison Printer manuals
Avery Dennison
Avery Dennison SNAP 500 User manual
Avery Dennison
Avery Dennison Monarch 2 Operating and maintenance manual
Avery Dennison
Avery Dennison Monarch Tabletop Printer 2 User manual
Avery Dennison
Avery Dennison SNAP 500 User manual
Avery Dennison
Avery Dennison MONARCH 9416 XL User manual
Avery Dennison
Avery Dennison MONARCH 9416 XL Installation and operating instructions
Avery Dennison
Avery Dennison MonarchNet2 9855 User manual
Avery Dennison
Avery Dennison 9417 User manual
Avery Dennison
Avery Dennison LOKPRINT 676 User manual
Avery Dennison
Avery Dennison TrafficJet User manual
Avery Dennison
Avery Dennison Monarch Service manual
Avery Dennison
Avery Dennison TTX 207 User manual
Avery Dennison
Avery Dennison Monarch Pathfinder Ultra Silver User manual
Avery Dennison
Avery Dennison Monarch 9419 Service manual
Avery Dennison
Avery Dennison Monarch 9460 Service manual
Avery Dennison
Avery Dennison Monarch 9485 User manual
Avery Dennison
Avery Dennison Monarch ADTP1 User manual
Avery Dennison
Avery Dennison MONARCH 9416 XL Technical Document
Avery Dennison
Avery Dennison 686 HT User manual
Avery Dennison
Avery Dennison Monarch Pathfinder Ultra Platinum 9462 User manual
