Avery Dennison MONARCH 9416 XL Installation and operating instructions

MONARCH®9416®XL®KNIFE

ADDENDUM

This Addendum contains supply loading procedures for the

Thermal Direct and Thermal Transfer printers with the knife

installed. For more detailed information, refer to the

Equipment Manual on our Web site (www.monarch.com).

Loading Supply for Non-Peel Mode

This section describes how to load supply to print in non-peel

(continuous) mode. If you have a thermal direct printer (does

not require a ribbon), make sure you load thermal direct

supply. If you have a thermal transfer printer (requires a

ribbon), make sure you load thermal transfer supply.

Make sure the black mark/die cut sensor is set correctly for

your supply type. See “Adjusting the Black Mark/Die Cut

Sensor,” in the Equipment Manual for more information.

Note: If you run out of supply, do not turn off the printer

when reloading the supply. You may lose your data.

The printer resumes printing when reloaded.

1. Remove and discard the tape from a new roll of supply.

Unwrap and discard supply with any glue residue.

2. Press the release levers towards the front of the printer to

release the cover.

3. Lift open the cover.

4. Remove the supply holder guide from one end of the

supply holder.

1.5-inch Supply

Core Adapter

Supply Holder

Supply Holder Guides

5. Slide a roll of supply onto the supply holder.

Note: If the core diameter on your roll of supply is 1 inch in

diameter, remove the 1.5-inch supply core adapters.

6. Place the supply holder guide back onto the end of the

supply holder. If you are using the supply core adapters

for 1.5-inch core supply, push the supply core adapters

into the ends

of the supply.

7. Insert the ends of the supply holder into the slots in the

supply roll mount.

Supply Roll Mount

Dial

8. Turn the dial to adjust the supply guides to their widest

position.

9. For thermal direct printers, feed the supply, printing side

up, under the supply guides and over the platen roller.

Supply

Knife

Supply Guides

10. Press the supply under the supply guides.

11. Move the supply guides so that they barely touch the

edges of the backing paper.

12. Feed the supply through the slot on the back of the knife.

13. Close the cover until it locks in place.

For thermal transfer printers, close the cover by lifting

the cover slightly and pulling the bottom of the cover

support forward towards the front of the printer.

Close the cover slowly and make sure it latches

securely.

Note: If you do not latch the cover completely, poor print

quality may result.

14. Press the FEED button. The indicator light should be

GREEN.

15. Calibrate the supply if necessary. See “Calibrating the

Supply,” in the Equipment Manual for more information.

Using the Knife

You can use NiceLabelsoftware to activate the knife or

MonarchPrinter Control Language II (MPCLII).

With NiceLabelStarter Edition Software

1. Select Label Setup from the File menu.

2. Select Next>.

3. Select the printer, for example Monarch 9416TT2XL 203

dpi printer. Then, click Properties…

4. Select the Advanced tab and set the Cutter option to

Never or enter the number of Every label(s) to cut. If you

enter 1, the printer cuts after each label.

5. Set the Cut position (in inches) if necessary.

6. Click OK.

7. Click Finish.

With MPCLII

Set the cut_type option in the Batch Control Field to 1.

Defining the Batch Control Field

The batch header must precede this field. The batch control

field defines the print job and applies only to the batch that

immediately follows.

Syntax E,feed_mode,batch_sep,print_mult,

multi_part, cut_type,cut_mult¦

E1. E Batch Control Field.

E2. feed_mode Feed Mode. Options:

0Continuous Feed (default)

1On-demand

E3. batch_sep Batch Separator. Use 0.

E4. print_mult Number of tags with the same image.

0 is the default. Range: 1to 999

E5. multi_part Number of identical parts on one tag.

0 is the default. Range: 1to 5

E6. cut_type Enables or disables the knife:

0No cut (default)

1Cuts before, during, and after

the last tag.

E7. cut_mult Number of tags to print before

cutting. A cut multiple of one cuts

after each tag. The range is 0 to

32,000. 0 is the default. The cut

multiple is a multiple of the print

quantity. If the cut multiple is three

and the print quantity is 16, then five

sets of three tags and one set of one

tag is produced.

Example E,0,0,0,0,1,0¦

Defines a batch control field. The feed mode is set for

continuous and a batch separator is not printed. The print

multiple and multi-part supply are set to 0 (not used). The

knife cuts before, during and after the last tag in a batch.

Example E,0,0,1,1,3,2¦

Defines a batch control field. The feed mode is set for

continuous and a batch separator is not printed. The print

multiple and multi-part supply are set to 1. The knife cuts

three sets of two tags when the print quantity is 6.

For more information about using MPCLII, refer to the Packet

Reference Manual on our Web site.

Knife Specifications

Cut Thickness: 0.28mm (Max.)

Cut Width: 120mm

Label Height: 15mm (Min.)

Cut Interval: Once per second (Max.)

Life: 500,000 cuts (Max. using supply

between 0.06mm-0.12mm thick)

100,000 cuts (Max. using supply

0.28mm thick)

Operating Limits:

Relative Humidity:

23°to 122°F

(-5°to 50°C)

10% to 80% (non-condensing)

Storage Limits:

Relative Humidity:

14°to 158°F

(-10°to 70°C)

5% to 95% (non-condensing)

Other manuals for MONARCH 9416 XL

Table of contents

Other Avery Dennison Printer manuals

Avery Dennison

Avery Dennison Monarch 9419 User manual

Avery Dennison

Avery Dennison 9417 User manual

Avery Dennison

Avery Dennison TC9820PHI User manual

Avery Dennison

Avery Dennison Monarch TC6039SA Service manual

Avery Dennison

Avery Dennison 686 HT User manual

Avery Dennison

Avery Dennison M09416 TTXLI User manual

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Platinum 9462 User manual

Avery Dennison

Avery Dennison AP7.t User manual

Avery Dennison

Avery Dennison Pathfinder 6059 Service manual

Avery Dennison

Avery Dennison Monarch 938 User manual

Avery Dennison

Avery Dennison FreshMarx 9417 Service manual

Avery Dennison

Avery Dennison SNAP 700 Operating manual

Avery Dennison

Avery Dennison Monarch ADTP1 User manual

Avery Dennison

Avery Dennison TTX 207 User manual

Avery Dennison

Avery Dennison Monarch 9825 User manual

Avery Dennison

Avery Dennison Monarch 9485 User manual

Avery Dennison

Avery Dennison AP7.t User manual

Avery Dennison

Avery Dennison Monarch 9460 SNP Service manual

Avery Dennison

Avery Dennison Monarch ADTP1 User manual

Avery Dennison

Avery Dennison SNAP 600 User manual

Avery Dennison

Avery Dennison Monarch 9855 Service manual

Avery Dennison

Avery Dennison MonarchNet2 9855 User manual

Avery Dennison

Avery Dennison Monarch Tabletop Printer 2 User manual

Avery Dennison

Avery Dennison ALS 104 User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide