Argo HPL Manual

0.8180.612.01 06/2012

ARGO HPL/SCL

TECHNICAL DATA & SERVICE MANUAL

Pagina 1

Page

SPECIFICATIONS

1) Unit specifications 3

2) Major Component specifications 4

BOPERATING RANG

CDIMENSIONAL DAT

DREFRIGERANT FLOW DIAGRAMS 8

EFUNCTIONS

1) System operation control 9

2) Cool Mode Operation 9

3) Heat Mode Operation 9

4) Auto Mode Operation 10

5) Dry Mode Operation 11

6) Fan Mode Operation 11

7) Auto Fan Speed 11

8) Forced Mode 12

9) Protection operations 12

10) Defrost 14

11) I FEEL Function 14

12) HI POWER mode 14

13) Heater resistance 14

14) NIGHT Function 15

15) LED OFF Function 15

16) Capacity test mode 15

17) Diagnostic 16

18) Address 17

19) Manual Unit Control and Led Indicators 18

20) Drain Pump 19

21) Safety thermostat 19

FELECTRIC WIRING DIAGRAMS 20

GTROUBLESHOOTING 21

HCHECKING ELECTRICAL COMPONENTS

1) Measurement of Insulation Resistance 29

2) Checking Continuity of Fuse on PCS Ass'y 29

3) Checking Motor Capacitor 29

Table of contents

Pagina 2

SPECIFICATIONS

1) UNIT SPECIFICATIONS

COOLING HEATING

BTU / h 6310 7750

kW 1,85 2,27

Air circulation (high/med/low) m3/ h

Moisture removal (high speed) Cooling l / h 0,6 ---

Voltage rating V

vailable voltage range V

Running Ampere (air conditioner) A 3,2 3,2

Power input (air conditioner) W 710 715

Power factor 0,96 0,97

C.O.P 2,61 3,17

Refrig./Stand. Charge at shipmen R410A

Ducts diameter ( 2pcs ) mm

NOTE

Rating conditions:

670-540-130

ARGO HPL/SCL

220 - 240

Fan speed (air conditioner)

Wireless remote control unit

ON / OFF 24 hours and programTimer

Control unit

198 - 264

UNIT MODEL

Heating: outside air temp.: 7° C DB, 6° C WB, indoor air temp.: 20° C DB

FEATURES

Controls / temperature control Microprocessor / I.C. Thermostat

Airflow direction

(Indoor)

Horizontal

Washable, easy access

Electronic expansion valve

Rotary (hermetic) DC inverter

Auto

Cooling: outside air temp.: 35° C DB, indoor air temp.: 27° C DB, 19° C WB

Condensate drain system

Compressor

Air filter

Refrigerant control

Data can be changed without notice

Air conditioner Hi/Me/Lo dB(A) 65-62-59

Air conditioner Hi/Me/Lo dB(A) 65-63-61

Capacity (air

conditioner)

Power source 220 - 240 V 50 Hz

PERFORMANCES

Power noise level

(Indoor)

DIMENSIONS AND WEIGHT

Power noise level

(outdoor)

ELECTRICAL RATINGS

162

By duct

3 + Auto

650g

Vertical

Manual

Net weight

162

Height

Widht

Depht

Holes diameter in the wall (2)

839

260-280

735

Pagina 3

2) MAJOR COMPONENT SPECIFICATIONS

Controls

Model

Resistance (at 25° C) kΩ

Model

Number / Diameter / Lenght mm

No. of pole / rpm (230 V, high)

rpm (230 V, high/ medium/ low)

Power input (high) W

Power output (high) W

Coil resistance (at 25° C) Ω

°C

μF

VAC

Model

Number / Diameter / Lenght mm

No. of pole / rpm (230 V)

rpm (230 V high/ medium /low)

Nominal input (high/ medium7 low) W

Coil resistance (at 25° C) Ω

°C

μF

VAC

2220/ 1735/ 1345

WHT-GRY: 12± 5%

BRN-WHT: 30± 5%

YLW-PNK: 44 ±10%

BLU-BLK: 69± 5%

GRY-BLK: 34± 5%

Centrifugal 1 / Ø146 / 140

D2E 146 - HS99 - 99

10 ± 5%

FAN & FAN MOTOR (FMI)

10 ± 5%

THERMISTOR (COMP. DISCHARGE SENSOR) TH4 NTC (with brass pipe)

10 ± 5%

THERMISTOR (ROOM SENSOR) TH1 SAC W-REM

THERMISTOR (INDOOR COIL SENSOR) TH2 NTC (with brass pipe)

420

10 ± 5%

2100/ 1760 / 730

Cross-flow 1 / Ø100 / 515

167/ 118/ 104

(Internal bimetallic type)

Open

Setting

384208055

thermal protector

NTC (with brass pipe)

TMR : blu - STB : orange - OPR : green

10 ± 3%

REMOTE CONTROL UNIT

Run capacitor (C1)

CONTROLLER (PCB)

SWITCH INDICATOR ASSY PCB

Led color

150 ± 5K

Autoreset

THERMISTOR (OUTDOOR AIR SENSOR) TH3

Safety device

UNIT MODEL ARGO HPL/SCL

Part No.

Control circuit fuse (F1)

Microprocessor

sac dci ODU

6,3x32 - 12,5A

1,5

Safety device

Run capacitor (C2)

Setting Close

Open 130 ± 8

UF2Q-21SC5P

THERMISTOR (OUTDOOR AIR SENSOR) TH5

FAN & FAN MOTOR (FMO) 440

BRN-WHT: 164 ±10%

WHT-VLT: 69 ±10%

VLT-ORG: 33 ±10%

YLW-ORG: 74 ±10%

79 ± 15

Pagina 4

Model

Coil resistance (at 20° C) Ω

Ω

overload protection

thermostat Open °C

Close °C

Operating amp. (Ambient temp. 25° C)

Model

Contact rating

Coil supply VAC

Coil resistance (20 °C) kΩ

Model

Contact rating

Coil supply VAC

Coil resistance (20 °C) Ω

Model

type / switching point

Contact rating

Model

type / switching point

Contact rating

Model

Coil rating

Coil resistance

Model

Coil rating

Coil resistance

Model

voltage V

power W

resistance Ω(at 20°C)

Model

contact rating V

Model

rating voltage

rating current A (rms)

Model

Inductance mH

rating current A

resistance Ω(at 20°C)

1.68 ± 10%

0.13 ± 10%

UNIT MODEL ARGO HPL/SCL

EMI FILTER (EF)

SAFETY FLOAT SWITCH (FS)

P200AC-001

10SS4-1BA2-BR-Q2

115/230 Vac , 50/60Hz

230 Vac - 0,4 A

05050A1

230

800 (+5% -10%)

66 (-5% +10%)

ZCAM-MD12EX(Coil) ZCAM-BD15EX (Valve)

DC 12 V

46 ± 4%

ELECTRICAL HEATER (RE)

SQ-136 (Coil) SHF-4H-23U (Valve)

AC 220/240 V, 50 Hz, 6W

1440 ± 5%

ELECTRONIC EXPANSION VALVE (EEV)

4-WAY VALVE (20S)

POWER RELAY (PR)

OMRON G4F

16A - 250V

IMIT 541741

20 A - 250 V

SAFETY THERMOSTAT (ST)

LS1 / 85°C

AUTOMATIC THERMOSTAT (AT)

IMIT 541873

LS3 / 65°C

External

5A - 230V

CBMF374125

158 ± 10%

PUMP RELAY (RP)

230

17,2 ± 10%

H62S

INDUCTOR

15A - 250V

COMPRESSOR (CM)

oil: Freol a68ES-T or SUNICE T-68

Nominal cooling capacity

115°C

320

2770

software protection

Rotary ( Hermetic)

W-U : 2.73

UG9A090FUAJP

U-V : 2.78

V-W : 2.83

Pagina 5

Model

Rating

Nominal intput

Coil resistance (at 20° C) Ω

FLAP MOTOR (FLP)

Type

Model

Rating

Coil resistence (Ambient temp. 25°C) Ω

HEAT EXCHANGER COIL (EVAPORATOR

)

Coil

Rows

Fin pitch mm

Face area m

HEAT EXCHANGER COIL (CONDENSER

)

Coil

Rows

Fin pitch mm

Face area m

THERMOSTATIC VALVE DRAIN PA

Open °C

Close °C

Stroke mm

OPERATING RANGE

Aluminium plate fin / copper tube

1,3

0,111

DP 25-1101-07 or

DP 25-1107-01

4,4

15,5

5,1

220-240VAC~50Hz

Model

1,3

5W - 0,05A

Aluminium plate fin / copper tube

Stepping motor

MP24GA1

778 ± 8%

UNIT MODEL

291036

CONDENSATE PUMP (PC)

ARGO HPL/SCL

0,107

DC 12V

WHT-BLU (respectively 4 wires) : 380 ± 7%

Dry Maximum 32° C BS/ 80% R.H. 43° C DB

Minimum 10° C BS/ 80% R.H. -15° C DB

27° C DB

indoor room 30% R.H.

24° C DB / 18° C WB

-15° C DB

Indoor air intake temp.

32° C DB/ 23° C WB

10° C DB/ 6° C WB

Outdoor air intake temp.

43° C DB

-15° C DB

Cooling

Heating

Temperature

Maximum

Minimum

Maximum

Minimum

Pagina 6

DIMENSIONAL DATA

All dimensions are in mm

Pagina 7

REFRIGERANT FLOW DIAGRAM

ARGO HPL/SCL

Pagina 8

FUNCTIONS

1 System operation control

The units receives the user input (fan speed, flap position etc) through remote controller

which sends signal every time a button is pressed and in any case, automatically, every 5 minutes

During operation compressor speed can be subjected to change due to thermal load variations

or protection activations but in any case:

• The minimum time interval between an OFF and a ON operation is not lower than 3 minutes

• The minimum operating time is not lower than 3 minutes

• The maximum acceleration/deceleration rate is fixed at 20rpm /sec

• During the start-up compressor speed increases according to a defined rule which is

independent from the thermal load calculation.

2 Cool Mode Operation

In Cooling Mode, the operation of the compressor (CM), Outdoor Fan (FMO) and Indoor Fan (FMI) are

determined by:

1) the difference between the room air temperature (RAT) and the set point temperature (SPT)

2) the protection level at which the system is operatin

3) the thermal load in the room

NOTES

In addition to the temperature difference of above, the operation of the main components (CM, FMO,

FMI) is also controlled by protection function.

The minimum off time of compressor is 3 minutes.

The indoor fan can change speed only after it has operated at the same speed for 30 sec if in AUTO

and 1 sec for the other settings (High, Med, Low).

3 Heat Mode Operation

The Heating mode operation is similar to the Cooling mode operation. The CM, FMO and FMI are

controlled by the same parameters.

The FMI will not be turned on until the indoor coil temperature is warm enough to prevent the supply of

cold air (see COLD DRAFT PREVENTION feature for details).

The indoor fan can change speed only after it has operated at the same speed for 30 sec if in AUTO

and 1 sec for the other settings (High, Med, Low).

Pagina 9

4 Auto Mode Operation

In Auto Mode, the unit switches automatically between the Auto Cooling and Auto Heating in order to

maintain the room temperature (RAT) at the prescribed set point (SPT).

The switching between the two modes is according to the above graph and following table

If -3°C ≤Dt ≤-1°C and the compressor is off for more than 1 hour

If Dt ≤-3°C and compressor is off for more than 3 minutes

If 1°C ≤Dt ≤3°C and the compressor is off for more than 1 hour

If Dt ≥3°C and compressor is off for more than 3 minutes

Dt = RAT - SPT

Refer to the sections 1 COOLING MODE and 2 HEATING MODE for system operation details.

COOLING ---> HEATING

HEATING ---> COOLING

Pagina 10

This manual suits for next models

Table of contents

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual