AMX MX Series User manual
MX Series
INSTRUCTION MANUAL
Table of Contents
MX Series of Wireless
Slide Projector Controllers ......................3
Using the MX Series ....................................4
Functional Overview ....................................5
Single-projector control models ......................5
Dual-projector control model ..........................5
MX2(L), MX4(L) ................................................6
MX2/MX2L hand controls ..................................6
MX4/MX4L hand controls ..................................6
Installation (MX2, MX4 receivers) ....................7
MX3(L), MX4A(L) ............................................8
MX3/MX3L hand controls ..................................8
MX4A/MX4AL hand controls ............................8
Installation (MX3, MX4A receivers) ..................9
Laser Pointer (Optional) ..........................10
MX12 ..................................................................11
MX12 hand controls ........................................11
Installation (MX12 receiver) ............................12
Communications Settings ....................14
The communications DIP switch ....................14
Setting the communication DIP switches ......14
Battery Replacement ................................17
Troubleshooting ............................................18
Common Questions ..................................19
2
The MX series of slide projector controllers offers
total slide projector control combined with freedom
of movement for convenient, professional audiovisual
presentations. From simple forward and reverse of
one projector to multi-function control of two pro-
jectors, the MX series includes nine models that are
compatible with most standard projectors and a wide
variety of applications. All systems feature a hand-
held transmitter that modulates radio frequency
(RF) signals that are omni-directional. The control
range is 75 feet and is effective through walls, glass,
or screens.
Each MX transmitter is housed in a durable, hand-
held case with easy-to-use, ergonomically placed
pushbuttons. The MX transmitters (except the MX12)
are available with an optional laser pointer for use
in presentations. MXreceivers are enclosed in a
compact, unobtrusive case. Installation is simple.
Control cables simply plug into the remote control
jack on the projector. User-definable codes allow
multiple systems to be used in the same area.
Contact your local AMX dealer for a complete
brochure on the AMX line of remote control sys-
tems for audiovisual and environmental equipment.
MX Series of Wireless Slide Projector Controllers
3
To operate the MX series transmitters:
1. To ensure maximum operating range, place the MX
receiver on a non-metallic surface, away from the
projector.
2. For the MX unit to operate, the controlled projector
must have its power switch in an ON position. Select
LOW or HIGH lamp (see switch D on the installation
diagram of your MX receiver).
3. With the MX transmitter, move away from the projec-
tor and press a pushbutton on the transmitter to test
the MX receiver.
Using the MX Series
4
Functional Overview
Single-projector control models
Figure 1 lists the functionality of the MX single-projector controllers.
Dual-projector control model
Figure 2 lists the functionality of the MX12 dual-projector controller.
Figure 1
Functionality of
MX single-projector
controllers
MODEL FORWARD REVERSE FOCUS AC POWER
ON/OFF
MX2(L) ••
MX3(L) •• •
MX4(L) •••
MX4A(L) ••••
Figure 2
Functionality of
MX12 dual-projector
controller
MODEL FWD REV FWD REV FOCUS AC POWER
ON/OFF
MX12 ••••• •
Simultaneous Independent Projector Action
5
MX2(L), MX4(L) Transmitters
MX2/MX2L hand controls
• FWD — Press to advance the projector.
• REV — Press to reverse the projector.
• TRIGGER (MX2) — Push the trigger on the bottom of the MX2
transmitter to advance the projector.
• TRIGGER (MX2L) — Push the trigger on the bottom of the MX2L
transmitter to activate the laser pointer.
MX4/MX4L hand controls
• FWD — Press to advance the projector.
• REV — Press to reverse the projector.
• FOCUS (left) — Press to move the lens out to focus the image.
• FOCUS (right) — Press to move the lens in to focus the image.
• TRIGGER (MX4) — Push the trigger on the bottom of the MX4
transmitter to advance the projector.
• TRIGGER (MX4L) — Push the trigger on the bottom of the MX4L
transmitter to activate the laser pointer.
Figure 3
MX2/MX2L
transmitter
Figure 4
MX4/MX4L
transmitter
6
MX2(L), MX4(L) Receivers
Installation (MX2, MX4 receivers)
Figure 5 shows an illustration of the installation of MX2
and MX4 receivers. To install MX2 and MX4 receivers:
1. Plug the 5-pin receiver cord (A) into the remote
receptacle on the projector (B).
2. When a Kodak®slide projector is used, the MX receiver
will draw power from the projector. In other cases —
such as another brand of projector or when dissolve
control is used — a power supply must be connected
(13.5 VAC, 520 MA).
3. If it is determined the power supply is needed, you will
need to obtain an MX-PS 13.5 VAC power supply. Plug
the power cord into any standard wall outlet (120 V)
and connect the power mini-plug to the receiver
power receptacle (C).
4. Extend the black antenna wire vertically.
5. Set the lamp switch on the projector (D) to either the
HIGH or LOW position.
Figure 5
Installation of MX2
and MX4 receivers
7
MX3(L), MX4A(L) Transmitters
MX3/MX3L hand controls
• FWD — Press to advance the projector.
• REV — Press to reverse the projector.
• POWER — Press both POWER pushbuttons simultaneously to toggle
AC power On/Off.
• TRIGGER (MX3) — Push the trigger on the bottom of the MX3 trans-
mitter to advance the projector.
• TRIGGER (MX3L) — Push the trigger on the bottom of the MX3L
transmitter to activate the laser pointer.
MX4A/MX4AL hand controls
• FWD — Press to advance the projector.
• REV — Press to reverse the projector.
• FOCUS (left) — Press to move the lens out to focus the image.
• FOCUS (right) — Press to move the lens in to focus the image.
• POWER — Press both POWER pushbuttons simultaneously to toggle
AC power On/Off.
• TRIGGER (MX4A) — Push the trigger on the bottom of the MX4A
transmitter to advance the projector.
• TRIGGER (MX4AL) — Push the trigger on the bottom of the MX4AL
transmitter to activate the laser pointer.
Figure 6
MX3/MX3L
transmitter
Figure 7
MX4A/MX4AL
transmitter
8
MX3(L), MX4A(L) Receivers
Installation (MX3, MX4A receivers)
Figure 8 shows an illustration of the installation of
MX3 and MX4A receivers. To install MX3 and MX4A
receivers:
1. Plug the 5-pin receiver cord (A) into the remote
receptacle on the projector (B).
2. Plug the projector AC power cord (E) into the AC
outlet on the rear of the MX receiver unit.
3. Plug the MX receiver power cord (C) into a standard
wall outlet.
4. Extend the black antenna wire vertically.
5. Set the lamp switch on the projector (D) to either the
HIGH or LOW position.
Figure 8
Installation of MX3
and MX4A receivers
9
Laser Pointer (Optional)
MX transmitters (except the MX12) are available with
an optional laser pointer to use in presentations. MX
transmitters equipped with the laser pointer are the
MX2L, MX3L, MX4L, and MX4AL.
The laser source is located at the front of the trans-
mitter, as shown in Figure 9. The laser is activated by
pushing the trigger on the bottom of the casing.
Please read the laser device warning decal shown in
Figure 10, on the bottom of MX transmitters equipped
with the laser pointer.
Figure 10
Laser device warning
Figure 9
MX transmitter with optional
laser pointer
10
This manual suits for next models
9
Table of contents
Other AMX Controllers manuals
AMX
AMX UPC20 Plus User manual
AMX
AMX NXA-WAPZD1100 User manual
AMX
AMX NXC-VAI4 User manual
AMX
AMX Axcent3 pro User manual
AMX
AMX SVSI SC-WPC User manual
AMX
AMX NetLinx Integrated Controller NI-3100 User manual
AMX
AMX NetLinx Integrated Controller NI-700 User manual
AMX
AMX NXI User manual
AMX
AMX NetLinx NI-2000 Operating instructions
AMX
AMX NetLinx Integrated Controller NI-4100 User instructions
AMX
AMX AXB-TCTCR TELEVISION CONTROLLERRECEIVER User manual
AMX
AMX Tango DAS-T0804-SIG User manual
AMX
AMX NXA-WAPZD1000 Parts list manual
AMX
AMX NetLinx NI-4000 User manual
AMX
AMX NXI User manual
AMX
AMX NetLinx Integrated Controller NI-900 User manual
AMX
AMX AXB-CAM User manual
AMX
AMX SX16+ Owner's manual
AMX
AMX NetLinx NI-4000 User manual
AMX
AMX SC-N8012 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
