Amana NGD7300W User instructions

Gas Dryer

PRODUCT MODEL NUMBERS

W10443045B

02/2012

NGD7300W

NOTE: Most installations require a minimum

5" (102 mm) clearance behind the dryer for

the exhaust vent with elbow. See “Venting

Requirements”.

Side view:

DRYER DIMENSIONS

Front view:

27"

(686 mm)

(25 mm)

353/8"

(899 mm)

31/2"

(89 mm)

29"

(736 mm)

Left or

right side

exhaust

67/8"

(174 mm)

15/8"

(41 mm)

471/8"

(1197 mm)

481/8"

(1238 mm)

Door open view:

Back view: Closet Installation (stacked washer and dryer): Closet installation (dryer only):

61/4"

(159 mm)

281/8"

(715 mm)

31/2"

(89 mm)

14"

(358 mm)

Electric

24 in.2

(155 cm2)

48 in.2

(310 cm2)

(25 mm)

(102 mm)

(76 mm)

34" recommended

(864 mm)

18" min.

(457 mm)

(76 mm)

Custom under counter installation (dryer only):

(25 mm)

39" min.

(990 mm)

Spacing for recessed area or closet

installation

All dimensions show recommended spacing

allowed, with tested spacing of 0" (0 mm)

clearance on sides and rear.

■Additional spacing should be considered

for ease of installation and servicing.

■Additional clearances might be required

for wall, door, and oor moldings.

■Additional spacing should be considered

on all sides of the dryer to reduce noise

transfer.

■For closet installation, with a door,

minimum ventilation openings in the top

and bottom of the door are required.

Louvered doors with equivalent

ventilitation openings are acceptable.

■Companion appliance spacing should

also be considered.

■No other fuel-burning appliance may be

installed in the same

closet as the dryer.

NOTE: Some models not recommended for

undercounter installation.

(25 mm)

51/2"

(140 mm)

24 in.2

(155 cm2)

48 in.2

(310 cm2)

(76 mm)

(152 mm)

71"

(1803 mm)

(25 mm)

(102 mm)

(178 mm)

18"

(460 mm)

Cabinet installation (dryer only):

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation

our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.

ELECTRICAL REQUIREMENTS

VENTING REQUIREMENTS

Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm)

diameter vent is required. Rigid or exible metal exhaust vent

must be used. Do not use plastic or metal foil vet. Exhaust hood

must be at least 12" (305 mm) from the ground or any object that

may be in the path of the exhaust.

Determine vent length and elbows needed for best

drying performance:

■Use following Vent System Chart to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specied

in Vent System Chart. Exhaust systems longer than those

specied will:

■Shorten life of dryer.

■Reduce performance, resulting in longer drying times

and increased energy usage.

Louvered Hood

Angled Hood

Box Hood

Exhaust hoods:

Recommended Styles:

Acceptable Style:

The dryer must be connected to the cold water faucet using new inlet hoses. Do not use old hoses. Do not overtighten.

Damage to the coupling can result.

A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit

are recommended.

GAS SUPPLY REQUIREMENTS

Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When

acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger