Allen-Bradley CompactLogix 1769-L20 User manual

Publication 1769-IN047C-EN-P - April 2003

Installation Instructions

1769-L20, 1769-L30 CompactLogix™ Controllers

(Cat. No. 1769-L20, 1769-L30)

Inside...

Before You Begin .................................................................................... 2

For More Information.............................................................................. 2

European Communities (EC) Directive Compliance ................................ 4

Hazardous Location Considerations ....................................................... 5

CompactLogix Controller Description ..................................................... 6

System Planning ..................................................................................... 6

Install the Controller ............................................................................... 7

Connect the Battery ................................................................................ 8

Assemble the System ............................................................................. 9

Mount the System ................................................................................ 10

Grounding Considerations .................................................................... 12

Select the Controller’s Operating Mode ............................................... 12

RS-232 Connections to the Controller .................................................. 13

Default Communication Configuration ................................................. 14

Using the Channel 0 Default Communication Push Button .................. 15

Troubleshoot the Controller Using the LEDs......................................... 16

Flash Upgrade the Controller Firmware................................................ 17

Specifications ....................................................................................... 18

Dimensions ........................................................................................... 19

Battery Handling, Storing, and Transporting ........................................ 20

21769-L20, 1769-L30 CompactLogix™ Controllers

Publication 1769-IN047C-EN-P - April 2003

Before You Begin

Use this document as a guide for installing and powering-up your 1769-L20, -L30

CompactLogix controller system. You should already be familiar with the

CompactLogix system components.

You must FLASH upgrade the firmware on your CompactLogix controller before

you can use it. The controller ships with firmware revision 1.x but must be

upgraded to match the version of RSLogix 5000 that you are using (e.g. if you are

using RSLogix 5000 V11, you must upgrade your CompactLogix controller firmware

to revision 11.x before using it. For more information on upgrading your

controller’s firmware, see page 17.

For More Information

If you would like a manual, you can obtain it as follows:

·download a free electronic version from the internet:

www.theautomationbookstore.com

·purchase a printed manual by:

–contacting your local distributor or Rockwell Automation representative

–visiting www.theautomationbookstore.com and placing your order

–calling 1.800.963.9548 (USA/Canada)

or 001.330.725.1574 (Outside USA/Canada)

For Information on Refer to this Document Pub. No.

How to use 1769-L20, -L30 CompactLogix™

controllers

CompactLogix™ System User Manual 1769-UM007

Programming the controller Logix5000™ Controllers Common

Procedures Programming Manual

1756-PM001

General instructions Logix5000 Controller General

Instructions Reference Manual

1756-RM003

Process control and drives instructions Logix5000 Controller Process Control

and Drives Instructions Reference

Manual

1756-RM006

Installing and operating Compact power

supplies

Compact™ 1769 Expansion I/O Power

Supplies Installation Instructions

1769-IN028

Installing and operating Compact I/O Compact 1769 Expansion I/O Installation Instructions for your

particular module

Installing and operating Compact I/O

analog modules

Compact 1769 I/O Analog Modules

User Manual

1769-UM002

How to use the 1769-ADN DeviceNet

adapter module

DeviceNet Adapter Module User

Manual

1769-UM001

Proper wiring and grounding techniques. Industrial Automation Wiring and

Grounding Guidelines

1770-4.1

1769-L20, 1769-L30 CompactLogix™ Controllers 3

Publication 1769-IN047C-EN-P - April 2003

Important User Information

Because of the variety of uses for the products described in this publication, those responsible for the

application and use of these products must satisfy themselves that all necessary steps have been taken to

assure that each application and use meets all performance and safety requirements, including any applicable

laws, regulations, codes and standards. In no event will Rockwell Automation be responsible or liable for

indirect or consequential damage resulting from the use or application of these products.

Any illustrations, charts, sample programs, and layout examples shown in this publication are intended solely

for purposes of example. Since there are many variables and requirements associated with any particular

installation, Rockwell Automation does not assume responsibility or liability (to include intellectual property

liability) for actual use based upon the examples shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation and Maintenance of

Solid-State Control (available from your local Rockwell Automation office), describes some important

differences between solid-state equipment and electromechanical devices that should be taken into

consideration when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or part, without written permission of

Rockwell Automation, is prohibited.

Throughout this publication, notes may be used to make you aware of safety considerations. The following

annotations and their accompanying statements help you to identify a potential hazard, avoid a potential

hazard, and recognize the consequences of a potential hazard:

WARNING

Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage,

or economic loss.

ATTENTION

Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

41769-L20, 1769-L30 CompactLogix™ Controllers

Publication 1769-IN047C-EN-P - April 2003

European Communities (EC) Directive Compliance

If this product has the CE mark it is approved for installation within the European

Union and EEA regions. It has been designed and tested to meet the following

directives.

EMC Directive

This product is tested to meet the Council Directive 89/336/EC Electromagnetic

Compatibility (EMC) by applying the following standards, in whole or in part,

documented in a technical construction file:

·EN 50081-2 EMC — Generic Emission Standard, Part 2 — Industrial

Environment

·EN 50082-2 EMC — Generic Immunity Standard, Part 2 — Industrial

Environment

This product is intended for use in an industrial environment.

Low Voltage Directive

This product is tested to meet Council Directive 73/23/EEC Low Voltage, by

applying the safety requirements of EN 61131-2 Programmable Controllers, Part 2 -

Equipment Requirements and Tests. For specific information required by

EN 61131-2, see the appropriate sections in this publication, as well as the

Allen-Bradley publication Industrial Automation Wiring and Grounding Guidelines

For Noise Immunity, publication 1770-4.1. and the Automation Systems Catalog,

publication B111.

This equipment is classified as open equipment and must be mounted in an

enclosure during operation to provide safety protection.

1769-L20, 1769-L30 CompactLogix™ Controllers 5

Publication 1769-IN047C-EN-P - April 2003

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to use in

hazardous locations.

Environnements dangereux

Cet équipement est conçu pour être utilisé dans des environnements de Classe 1,

Division 2, Groupes A, B, C, D ou non dangereux. La mise en garde suivante

s’applique à une utilisation dans des environnements dangereux.

WARNING EXPLOSION HAZARD

·Substitution of components may impair suitability for Class

I, Division 2.

·Do not replace components or disconnect equipment

unless power has been switched off or the area is known

to be non-hazardous.

·Do not connect or disconnect components unless power

has been switched off or the area is known to be

non-hazardous.

·This product must be installed in an enclosure. All cables

connected to the product must remain in the enclosure or

be protected by conduit or other means.

·All wiring must comply with N.E.C. article 501-4(b).

AVERTISSEMENT

DANGER D’EXPLOSION

·La substitution de composants peut rendre cet équipement

impropre à une utilisation en environnement de Classe 1,

Division 2.

·Ne pas remplacer de composants ou déconnecter

l'équipement sans s'être assuré que l'alimentation est

coupée et que l'environnement est classé non dangereux.

·Ne pas connecter ou déconnecter des composants sans

s'être assuré que l'alimentation est coupée ou que

l'environnement est classé non dangereux.

·Ce produit doit être installé dans une armoire.

61769-L20, 1769-L30 CompactLogix™ Controllers

Publication 1769-IN047C-EN-P - April 2003

CompactLogix Controller Description

System Planning

Consider the following when planning your CompactLogix system:

·The CompactLogix controller is always the left-most module in the system.

·The controller must be located within four modules of the system power

supply. Some I/O module’s may be located up to 8 modules away from the

power supply. See the documentation for your 1769 I/O modules for details.

·The 1769-L20 controller supports up to 8 I/O modules in a maximum of 2

I/O banks (1 expansion cable allowed).

·The 1769-L30 controller supports up to 16 I/O modules in a maximum of 3

I/O banks (2 expansion cables allowed).

·Each I/O bank requires its own power supply.

·Only one controller can be used in a CompactLogix system.

·A 1769-ECR (right end cap) or 1769-ECL (left end cap) is required to

terminate the end of the communication bus.

1 DIN rail latch 8 Channel 0 RS-232 Port

2 panel mounting tab 9 Channel 0 default communication push button

3 tongue and groove slots 10 Channel 1 RS-232 Port

4 stationary bus connector 11 Channel 1 RS-232 Port Status LED

5 status LEDs 12 battery door

6 key switch 13 battery door label

7 Channel 0 RS-232 Port Status LED 14 battery(1)

(1) See Connect the Battery on page 8 for the actual position of the battery.

15 battery connector

1769-L20 controller 1769-L30 controller

1769-L20, 1769-L30 CompactLogix™ Controllers 7

Publication 1769-IN047C-EN-P - April 2003

Install the Controller

The 1769-L20 and 1769-L30 controllers are suitable for use in an industrial

environment when installed in accordance with these instructions. Specifically, this

equipment is intended for use in clean, dry environments (Pollution Degree 2(1))

and with circuits not exceeding Over Voltage Category II(2) (IEC 60664-1).(3)

Prevent Electrostatic Discharge

Remove Power

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are

controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

ATTENTION

Electrostatic discharge can damage integrated circuits or

semiconductors if you touch bus connector pins. Follow these

guidelines when you handle the module:

·Touch a grounded object to discharge static potential.

·Wear an approved wrist-strap grounding device.

·Do not touch the bus connector or connector pins.

·Do not touch circuit components inside the module.

·If available, use a static-safe work station.

·When not in use, keep the module in its static-shield bag.

ATTENTION

Remove power before removing or inserting this module.

When you remove or insert a module with power applied, an

electrical arc may occur. An electrical arc can cause personal

injury or property damage by:

·sending an erroneous signal to your system’s field devices,

causing unintended machine motion

·causing an explosion in a hazardous environment

Electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create

electrical resistance.

81769-L20, 1769-L30 CompactLogix™ Controllers

Publication 1769-IN047C-EN-P - April 2003

Connect the Battery

The controller is shipped with the battery packed separately. To connect the

battery, follow the procedure shown below.

1. Slide the battery door (a) forward.

2. Insert the battery (b) into the battery holder. Insert the battery connector into

the connector port (c). The connector is keyed to engage only in the

correct polarity.

3. Slide the battery door (a) back until it clicks into position.

For information on battery handling, see page 20.

ATTENTION

Do not connect or disconnect the battery unless the

environment is known to be non-hazardous.

IMPORTANT Do not remove the plastic insulation covering the battery. The

insulation is necessary to protect the battery contacts.

1769-L20 controller 1769-L30 controller

1769-L20, 1769-L30 CompactLogix™ Controllers 9

Publication 1769-IN047C-EN-P - April 2003

Assemble the System

The controller can be attached to an adjacent I/O module or power supply before

or after mounting. For mounting instructions, see “Panel Mounting” on page 10, or

“DIN Rail Mounting” on page 11.

1. Disconnect line power.

2. Check that the lever of the adjacent module (A) is in the unlocked (fully

right) position.

3. Use the upper and lower tongue-and-groove slots (B) to secure the modules

together.

4. Move the module back along the tongue-and-groove slots until the bus

connectors line up with each other.

5. Use your fingers or a small screwdriver to push the module’s bus lever back

slightly to clear the positioning tab (C).

6. Move the module’s bus lever fully to the left (D) until it clicks. Ensure it is

locked firmly in place.

7. Attach an end cap terminator (E) to the last module in the system by using

the tongue-and-groove slots as before.

8. Lock the end cap bus terminator (F).

ATTENTION

When attaching the controller, power supply, and I/O

modules, it is very important that the bus connectors are

securely locked together to ensure proper electrical

connection.

10 1769-L20, 1769-L30 CompactLogix™ Controllers

Publication 1769-IN047C-EN-P - April 2003

Mount the System

Minimum Spacing

Maintain spacing from

enclosure walls,

wireways, adjacent

equipment, etc. Allow 50

mm (2 in.) of space on all

sides, as shown. This

provides ventilation and

electrical isolation.

Panel Mounting

Mount the controller to a panel using two screws per module. Use M4 or #8

panhead screws. Mounting screws are required on every module.

Panel Mounting Using the Dimensional Template

ATTENTION

During panel or DIN rail mounting of all devices, be sure that

all debris (metal chips, wire strands, etc.) is kept from falling

into the controller. Debris that falls into the controller could

cause damage while the controller is energized.

Bottom

Side Side

Top

CompactLogix

Controller

Power Supply

Compact I/O

End Cap

50 mm

(1.38)

132

(5.197)

122.6±0.2

(4.826±0.008)

(1.38)

28.5

(1.12)

(.985)

(.590)

(1.38)

CompactLogix Controller

Power Supply

Compact I/O

End Cap

NOTE: All dimensions are in mm (in.).

Hole spacing tolerance: ±0.4 mm (0.016 in.)

battery door

This manual suits for next models

Table of contents

Other Allen-Bradley Controllers manuals

Allen-Bradley

Allen-Bradley MicroLogix 1200 User manual

Allen-Bradley

Allen-Bradley ControlNet PLC-5 User manual

Allen-Bradley

Allen-Bradley 7760 User manual

Allen-Bradley

Allen-Bradley PowerFlex 755 IP00 User manual

Allen-Bradley

Allen-Bradley ControlLogix System 1756-L1 User manual

Allen-Bradley

Allen-Bradley PowerFlex 4M User manual

Allen-Bradley

Allen-Bradley CENTERLINE User manual

Allen-Bradley

Allen-Bradley Micro850 series User manual

Allen-Bradley

Allen-Bradley PLC-2/30 User manual

Allen-Bradley

Allen-Bradley 1769-L32E CompactLogix 5332E User manual

Allen-Bradley

Allen-Bradley Micro850 series User manual

Allen-Bradley

Allen-Bradley SMC-50 User manual

Allen-Bradley

Allen-Bradley PowerFlex 700S User manual

Allen-Bradley

Allen-Bradley powerflex 700 User manual

Allen-Bradley

Allen-Bradley PanelView 800 User manual

Allen-Bradley

Allen-Bradley MicroLogix 1400 User manual

Allen-Bradley

Allen-Bradley FlexLogix 1794-L33 User manual

Allen-Bradley

Allen-Bradley 1769 CompactLogix User manual

Allen-Bradley

Allen-Bradley 1492-IFM20F-F240-2 User manual

Allen-Bradley

Allen-Bradley PowerFlex 7000 User manual

Allen-Bradley

Allen-Bradley Studio 5000 Logix Emulate Owner's manual

Allen-Bradley

Allen-Bradley SLC 500 1747-L20 User manual

Allen-Bradley

Allen-Bradley GuardLogix User manual

Allen-Bradley

Allen-Bradley PowerFlex 525 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual