Akuvox R20A User manual

Allen Wrench x 1

Rope x 1

R20A x 1

ST4x20 screw x 4 Screw fixing seat x 4

M2.5x6 screw x 6Back cover x 1

Universal Accessories:

Wall-mounting screw x 4

Rubber Plug x 3 （S,M,L）

Camera

RF card reader



Mic

R20A

Infrared sensor





Cable locking plate x 1



M3x6 screw x 2

M4x30 screw x 2 Wall-mounting bracket x 1

R20A





Fix the wall-mounting bracket on

embedded box with two M4x30

screws.

Mark the two holes of the

wall-mounting bracket on the

wall.

Take down two M4x30 screws

and remove the wall-mounting

bracket.

Fix the wall-mounting bracket with two

ST4x20 screws and two M4x30 screws.

Insert two screw fixing

seats into the holes.

Use a hand drill with 5mm diameter bit to

make two 25mm depth holes in the

marked positions.







Mark the four holes of the

wall-mounting bracket on

the wall for the screws.

Use a hand drill with 5mm diameter

bit to make four 25mm depth holes

in the marked positions.

Fix the wall-mounting bracket

with four ST4x20 screws.

Insert four screw fixing seats into

the holes.

R20A



Fasten the back cover with four

M2.5x6 screws, then fix four

wall-mounting screws on the

back of R20A.

For convenient wiring, hang

R20A on the wall-mounting

bracket with rope.

Make cables go through the back

cover, connecting to the corresponding

interfaces of the main board.

Select a suitable size rubber plug

to push all the cables into the back

cover. Fix cable locking plate to

the back cover with two M2.5x6

screws.

After successful installation,

check the stability of device.

Insert the four wall-mounting screws on

the device into the corresponding holes

on the wall-mounting bracket, and then

press down to slide the wall-mounting

screws into the groove. Then use the

Allen Wrench to tighten the device with

two M3x6 screws.

R20A



Network Video Recorder

(third party)

SIP Video Phone

LAN

PoE PoE

R20A R20A

PoE PoE

R20A R20A

PC(third party)

PoE PoE

Indoor Monitor



1. While R20A starts up normally, hold the call button for several seconds after the Status

LED turns blue, voice system will enter IP announcement mode.

2. In announcement mode, the IP address will be announced periodically.

3. Press Call Button again to quit the announcement mode.

4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address is gained.

R20A



1. Access the Web UI: Input the IP address into web browser to configure the phone.

2. Account Registration: On web UI, go to the path: Account -> Basic page

more information)

3. Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button

to configure the call number.

4. Configure the code to open the relay: On web UI, go to the path: Intercom -> Relay

-> Relay ID/DTMF and choose the DTMF code number in corresponding area.



Make a call:

1. Press the call button to call indoor SIP Phone.

2. During the talk, called party can press pre-configured code number to unlock the door.

Receive a call:

R20A supports Auto Answer by default. Incoming call will be answered automatically.

R20A

Note: For more LED settings, please refer to R20 webUI: Intercom -> LED Setting.



R20A

AKUVOX (XIAMEN) NETWORKS CO., LTD.

ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA

www.akuvox.com

Notice Information

Akuvox R20A firmware contains third-party open source software under the terms of the GNU General Public License(G-

PL). Akuvox is committed to meeting the requirements of the GNU General Public License (GPL) and will make all

required source code available.

The source code of software under the terms of GNU GPL can be downloaded online: http://www.akuvox.com/gpl.

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is

subject to change without notice, any update to this document can be viewed on Akuvox’ s website: http://www.akuvox-

Other manuals for R20A

Table of contents

Popular Intercom System manuals by other brands

Bticino

Bticino LINEA 3000 Installation

MSI

MSI MSI-140 owner's manual

golmar

golmar Stadio Plus instruction manual

CyberData

CyberData 011211 series Installation quick reference

Vidos

Vidos duo M1021 user manual

Vimar

Vimar ELVOX 7539/E Installation and operation manual

SSS Siedle

SSS Siedle BTSV 850-03 operating instructions

Dahua

Dahua VTO Series quick start guide

Elvox

Elvox 5651 Wiring instructions

Videx

Videx VIDEOKIT Series owner's manual

Rocom

Rocom Doortello Business FW T2.05W2.04 user guide

Viking

Viking E-35-EWP product manual

Safeguard Supply

Safeguard Supply LRA-EX1000 user manual

SSS Siedle

SSS Siedle BFCV 850 Series operating instructions

GRD

GRD MAX V2 user manual

Alecto

Alecto ADI-250 user manual

Aiphone

Aiphone IE-8MD Installation & operation manual

Perel

Perel EDB4 user manual