AFRISO WMS-WP6 User manual
0036
Version: 07.2017.0
ID: 900.000.0384
Lindenstraße 20
74363 Güglingen
Telefon+49 7135 102-0
Service+49 7135-102-211
Telefax +49 7135-102-147
www.afriso.com
Copyright 2017 AFRISO-EURO-INDEX GmbH.All rights reserved.
Operating instruc-
tions
Boiler water low level alarm
WMS-WP6 - mechanical
2
About these operating instructions
EN
WMS-WP6
1 About these operating instructions
These operating instructions describe the boiler water low level alarm "WMS-
WP6" (also referred to as "product" in these operating instructions). These
operating instructions are part of the product.
• You may only use the product if you have fully read and understood these
operating instructions.
• Verify that these operating instructions are always accessible for any type
of work performed on or with the product.
• Pass these operating instructions as well as all other product-related doc-
uments on to all owners of the product.
• If you feel that these operating instructions contain errors, inconsisten-
cies, ambiguities or other issues, contact the manufacturer prior to using
the product.
There operating instructions are protected by copyright and may only be
used as provided for by the corresponding copyright legislation. We reserve
the right to modifications.
The manufacturer shall not be liable in any form whatsoever for direct or con-
sequential damage resulting from failure to observe these operating instruc-
tions or from failure to comply with directives, regulations and standards and
any other statutory requirements applicable at the installation site of the prod-
uct.
3
Information on safety
EN
WMS-WP6
2 Information on safety
2.1 Safety messages and hazard categories
These operating instructions contain safety messages to alert you to poten-
tial hazards and risks. In addition to the instructions provided in these oper-
ating instructions, you must comply with all directives, standards and safety
regulations applicable at the installation site of the product. Verify that you are
familiar with all directives, standards and safety regulations and ensure com-
pliance with them prior to using the product.
Safety messages in these operating instructions are highlighted with warning
symbols and warning words. Depending on the severity of a hazard, the
safety messages are classified according to different hazard categories.
In addition, the following symbols are used in these operating instructions:
DANGER
DANGER indicates a hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided,
can result in serious injury or equipment damage.
NOTICE
NOTICE indicates a hazardous situation, which, if not avoided, can
result in equipment damage.
This is the general safety alert symbol. It alerts to injury haz-
ards or equipment damage. Comply with all safety instruc-
tions in conjunction with this symbol to help avoid possible
death, injury or equipment damage.
This symbol alerts to hazardous electrical voltage. If this
symbol is used in a safety message, there is a hazard of
electric shock.
4
Information on safety
EN
WMS-WP6
2.2 Intended use
This product may only be used to secure boilers at heating systems (as per
EN 12828) with flow temperatures of up to 120 °C by signalling a low water
condition.
Any use other than the application explicitly permitted in these operating
instructions is not permitted and causes hazards.
Verify that the product is suitable for the application planned by you prior to
using the product. In doing so, take into account at least the following:
• All directives, standards and safety regulations applicable at the installa-
tion site of the product
• All conditions and data specified for the product
• The conditions of the planned application
In addition, perform a risk assessment in view of the planned application,
according to an approved risk assessment method, and implement the
appropriate safety measures, based on the results of the risk assessment.
Take into account the consequences of installing or integrating the product
into a system or a plant.
When using the product, perform all work and all other activities in conjunc-
tion with the product in compliance with the conditions specified in the oper-
ating instructions and on the nameplate, as well as with all directives, stand-
ards and safety regulations applicable at the installation site of the product.
5
Information on safety
EN
WMS-WP6
2.3 Predictable incorrect application
The product must never be used in the following cases and for the following
purposes:
• Use in heating systems with flow temperatures higher than 120 °C
• Use in high-pressure steam boilers and high-pressure hot water genera-
tors
2.4 Qualification of personnel
Only appropriately trained persons who are familiar with and understand the
contents of these operating instructions and all other pertinent product doc-
umentation are authorized to work on and with this product.
These persons must have sufficient technical training, knowledge and expe-
rience and be able to foresee and detect potential hazards that may be
caused by using the product
All persons working on and with the product must be fully familiar with all
directives, standards and safety regulations that must be observed for per-
forming such work.
2.5 Personal protective equipment.
Always wear the required personal protective equipment. When performing
work on and with the product, take into account that hazards may be present
at the installation site which do not directly result from the product itself.
2.6 Modifications to the product
Only perform work on and with the product which is explicitly described in
these operating instructions. Do not make any modifications to the product
which are not described in these operating instructions.
6
Transport and storage
EN
WMS-WP6
3 Transport and storage
The product may be damaged as a result of improper transport or storage.
NOTICE
DAMAGE TO THE PRODUCT
• Verify compliance with the specified ambient conditions during transport or
storage of the product.
• Use the original packaging when transporting the product.
• Store the product in a clean and dry environment.
• Verify that the product is protected against shocks and impact during trans-
port and storage.
Failure to follow these instructions can result in equipment damage.
7
Product description
EN
WMS-WP6
4 Product description
4.1 Overview
A. Test button
B. Cover
C. Nameplate
D. Unlock pushbutton
E. Vent screw
F. Welding socket
G. Switch off level (88 mm)
H. Float
I. Housing
J. Welding socket
K. Sludge removal opening
Fig. 1: WMS-WP6
A
E
D
C
B
I
G
H
J
K
F
8
Product description
EN
WMS-WP6
A. Cover
B. Test button
C. Switch
D. Unlock pushbutton
E. Screw connection with venting
F. Protective pipe
G. Float
H. Connection cable
Fig. 2: WMS-WP6 with short protective pipe
A
E
D
C
B
F
G
H
9
Product description
EN
WMS-WP6
4.2 Dimensions and connections
Fig. 3: WMS-WP6
335 mm
257.5 mm 77.5 mm
195 mm
54 mm
26.5 mm
20 mm
*
23 mm
112 mm
43 mm
PP
PP
10
Product description
EN
WMS-WP6
Fig. 4: WMS-WP6 with short protective pipe
83.5 mm
Approx.
10.5 mm
155 mm
R 2
Ø 56 mm
271 mm
36 mm
Other manuals for WMS-WP6
2
This manual suits for next models
5
Table of contents
Other AFRISO Security System manuals
AFRISO
AFRISO VA-ALERT W User manual
AFRISO
AFRISO VA-ALERT User manual
AFRISO
AFRISO WMS-WP6 User manual
AFRISO
AFRISO OM 1 User manual
AFRISO
AFRISO WWG 1 User manual
AFRISO
AFRISO GS 1.1 User manual
AFRISO
AFRISO OM 1 User manual
AFRISO
AFRISO AG 11 User manual
AFRISO
AFRISO WGA 01 User manual
AFRISO
AFRISO WGA 01 D User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual