Acrosser Technology ACE-B7400 Installation guide

P/N：220010423-G

ACE-B7400

Quick Manual

P/N：220010423-G

ACE-B7400 Quick Manual

1. I/O Connector and Key parts illustration (Top Side)

LED1

Green LED: Power On.

Orange LED: HDD Active.

PWR_BTN1

System Power Button

DVI-D1

DVI-D Connector.

DVI-I1

DVI-I Connector.

USB1

USB 2.0 Connector

CN25

RJ45 & USB 2.0 Connector

CN26

RJ45 & USB 2.0 Connector

COM1_2

RS-232 Connector

(9-bits Protocol supported).

COM3_4

RS-232 Connector

CN7

Gaming Input Isolation

Connector.

CN6

Gaming Input Isolation Connector.

CN5

Gaming Open-Drain Output

Connector.

CN4

Gaming Open-Drain Output

Connector.

CN3

TTL, RS232, RS485, cctalk

selectable connector

(UART RX,TX signal only).

CN2

2.1 Channel Audio Amplifier Output

Connector.

CN1

System Power Input Connector.

U43

AMD FT1 APU. (T48N/T52R)

U44

AMD Hudson-E1 Fusion

Controller Hub.

CF1

CF Card Slot 1.

CF2

CF Card Slot 2.

U40

Acrosser Gaming Core (AGC).

SATA1/SATA2

SATA 3.0 Connectors.

MINI-PCIE1

Mini-PCIe Slot.

CN_DIMM1/CN_DIMM2

DDR3 SODIMM Socket.

Maximum total 8GB.

CASESW1

Micro-switch for Chassis

Open/Close Detection.

BAT_BH1

CR2032 Battery Holder

for system RTC.

P/N：220010423-G

1.1 Rears-Panel I/O Configurations

CN7

Gaming Input Isolation Connector.

Micro-FIT 3.0mm

2*8 PINs

Signal Pin

Signal

1 Door Switch 1 9 Button 4

2 Door Switch 2 10 Button 5

3 Door Switch 3 11 Button 6

4 Door Switch 4 12 Button 7

5 Door Switch 5 13 Button 8

6 Button 1 14 Button 9

7 Button 2 15 Button 10

8 Button 3 16 Button 11

Note:

1.All input pin logical

high-level is +5V ~ +24V,

logical low-level is 0V ~

+1.5V.

CN6

Gaming Input Isolation Connector.

Micro-FIT 3.0mm

2*8 PINs

Signal Pin

Signal

1 Button 12 9 Touch-Cal Key-Lock

2 Button 13 10 Spare Key-Lock

3 Button 14 11 Coin-In Signal A

4 Button 15 12 Coin-In Signal B

5 Button 16 13 Bill-In

6 Dissolve Key-Lock

14 Hopper Sensor

7 OM Key-Lock 15 GPI 0

8 Setup Key-Lock 16 GPI 1

Note:

1.All input pin logical

high-level is +5V ~ +24V,

logical low-level is 0V ~

+1.5V.

2.Coin-In Signal A, Coin-In

Signal B, Bill-In, and

Hopper Sensor support

input counter function.

CN5

Gaming Open-Drain Output Connector.

Micro-FIT 3.0mm

2*10 PINs

Signal Pin

Signal

1 Key-in Meter 11 Coin-Enable

2 Bill-in Meter 12 Bill-Enable

3 Coin-in Meter 13 Hopper-SSR

4 Pay-out Meter 14 GPO 0

5 Key-out Meter 15 GPO 1

6 Hand-pay Meter 1

16 GPO 2

7 Hand-pay Meter 2

17 GPO 3

8 Spare Meter 18 GPO 4

9 GND 19 GND

10 IBUT2 20 GND

Note:

1.Eight Meters support

pulse-Generator function.

2.All output pin is open-drain

circuit and operation

maximum voltage cannot

over +30V.

3.IBUT2 is short to onboard

ibuttom2 connector.

P/N：220010423-G

CN4

Gaming Open-Drain Output Connector.

Micro-FIT 3.0mm

2*10 PINs

Signal Pin

Signal

1 LAMP 1 11 LAMP 9

2 LAMP 2 12 LAMP 10

3 LAMP 3 13 LAMP 11

4 LAMP 4 14 LAMP 12

5 LAMP 5 15 LAMP 13

6 LAMP 6 16 Tower LAMP 1

7 LAMP 7 17 Tower LAMP 2

8 LAMP 8 18 Tower LAMP 3

9 GND 19 GND

GND 20 GND

Note:

1.Each LAMP output supports

open-drain 500mA

(max)

current;

each Tower LAMP output supports

open-drain 1A

(max)

current.

2.All output pin is open-drain circuit

and operation maximum voltage

cannot over +30V.

CN3

Two TTL, RS232, RS485, ccTalk selectable connector (UART RX & TX signal only)

Note: mode selected by JP6~JP13 (Please see Appendix A.)

Micro-FIT 3.0mm

2*7 PINs

Signal Pin

Signal

COM5 TTL/ 232 Tx/ 485 +

8 COM5 TTL/ 232 Rx/ 485 -

COM6 TTL/ 232 Tx/ 485 +

9 COM6 TTL/ 232 Rx/ 485 -

COM5 ccTalk Data 10

COM6 ccTalk Data

COM5 ccTalk Vcc 11

COM6 ccTalk Vcc

GND 12

GND

GND 13

GND

GND 14

GND

CN2

2.1 Channel Audio Amplifier Output Connector.

Micro-FIT 3.0mm

2*3 PINs

Signal Pin

Signal

Front Left + 4 Front Left -

Front Right +

5 Front Right -

LFE + 6 LFE -

Note:

1. Audio Amplifier is D-type amp.

Amplified Right and Left channel

support 10Watt

(max)

Output,

Amplified LFE channel supports

20Watt

(max)

Output.

CN1

System Power Input Connector.

Micro-FIT 3.0mm

2*4 PINs

Signal Pin

Signal

1 +12V 5 +12V

2 GND 6 GND

3 GND 7 GND

4 +12V 8 +24V

Note:

1.+12V Power Input voltage

tolerance is ±10%.

2.+24V Power Input is only use for

cctalk Vs power supply.

P/N：220010423-G

2. Connector & Jumper setting definition (Top Side)

FPIO1

System Power Button & Reset

connector

CN_USB1

USB 2.0 Connector

CN_USB2

USB 2.0 connector

SYSFAN2

System FAN Connector 2.

APUFAN1

APU FAN Connector.

SPAREIO1

JST 2.0mm Gaming Spare-IO

Connector. (16-bits GPIO)

SW1

8-bit DIP-Switch Input for AGC.

SATA_PWR1

SATA_PWR2

SATA Power Connectors.

CLRCMOS

Clear System CMOS Jumper.

JP6 ~ JP13

CN3 Output Signal Selection

Jumper (TTL, RS232, RS485

or ccTalk)

SYSFAN1

System FAN Connector 1.

IButtom2

External i-Button Connector.

JP2

JP3

SRAM A, B Clear Jumper.

JP4

JP5

Bill-enable, Coin-enable

Preset Jumper.

BAT_A1,

BAT_B1

Lithium Battery Connector for

SRAM, AGA and secured RTC.

JP18

RS-485 Terminal Resistor

Selection Jumper for CN3

(UART 6)

JP17

RS-485 Terminal Resistor

Selection Jumper for CN3

(UART 5)

AUDIO1

Internal 5.1 Channel Audio

Pin-Header.

JP1

cctalk Supply Power Selection

Jumper.

CASESW2

JST 2.0mm Chassis

Open/Close Detection

Connector

P/N：220010423-G

2.1 Connectors and Jumpers Setting

FPIO1

System Power Button & Reset connector

CN_USB1

CN_USB2

USB 2.0 Connector

Function

1-2

Power Button Connector

3-4

Short: Auto Power-on

Open: Power-on by

Pin1-2 Button

5-6

Reset Button Connector

Note:

Default short Pin3-4 be Auto-Power-

JST 2.0mm

Signal

1 VCC (+5V)

2 Data+

3 Data-

4 GND

5 N.C

SYSFAN2

System FAN Connector 2.

APUFAN1

APU FAN Connector.

Signal

1 GND

2 +12V

3 Feedback

Signal

1 GND

2 +12V

3 Feedback

SPAREIO1

JST 2.0mm Gaming Spare-IO Connector.

(16-bits GPIO)

SW1

8-bit DIP-Switch Input for AGC.

Signal Pin

Signal

1 Bit0 2 Bit8

3 Bit1 4 Bit9

5 Bit2 6 Bit10

7 Bit3 8 Bit11

9 Bit4 10

Bit12

Bit5 12

Bit13

Bit6 14

Bit14

Bit7 16

Bit15

GND 18

+3.3V

GND 20

+3.3V

SW 1~8 Signal

ON +3.3V

OFF GND

P/N：220010423-G

SATA_PWR1

SATA_PWR2

SATA Power Connectors.

CLRCMOS

Clear System CMOS Jumper.

JST 2.5mm

Pin Signal

1 +12V

2 GND

3 +3.3V

4 +5V

Jumper Function

1-2

(default) Normal

2-3 Clear CMOS

JP6 ~ JP13

CN3 Output Signal Selection Jumper

(TTL, RS232, RS485 or ccTalk) SYSFAN1

System FAN Connector 1.

Please See Appendix A.

(Default set to be RS232)

Signal

1 GND

2 +12V

3 Feedback

IButtom2

External i-Button Connector. JP2 ,JP3

SRAM A, B Clear Jumper.

JST 2.0mm

Pin1 is short to rear-panel CN5

connector Pin10

Signal

1 I-Button Signal

2 GND

Jumper Function

1-2

(default) Normal

2-3 Clear SRAM

JP4 ,JP5

Bill-enable, Coin-enable Preset Jumper. BAT_A1 ,BAT_B1

Lithium Battery Connector for SRAM, AGA and

secured RTC.

Jumper Function

1-2

(default) Preset is “High”.

2-3 Preset is “Low”.

Note:

“High” means Bill-enable, Coin-enable

open-drain output is short to ground.

“Low” means Bill-enable, Coin-enable

open-drain output is open

Pin Signal

1 POWER

2 GND

P/N：220010423-G

JP18

RS-485 Terminal Resistor Selection Jumper for

CN3

(COM 6). JP17

RS-485 Terminal Resistor Selection Jumper for

CN3 (COM 5).

Jumper Function

1-2 Termination

2-3

(default) Non

Note:

Terminal resistor is 120ohm.

Jumper Function

1-2 Termination

2-3

(default) Non

Note:

Terminal resistor is 120ohm.

AUDIO1

Internal 5.1 Channel Audio Pin-Header. JP1

ccTalk Supply Power Selection Jumper.

Signal Pin

Signal

1 Front-L 2 Front-R

3 GND 4 GND

5 Surround-L

6 Surround-R

7 IO4 GND 8 GND

9 Center 10

LFE

Jumper Function

1-2

(default) +12V

2-3 +24V

power is from CN1 external power

supply.

CASESW2

JST 2.0mm Chassis Open/Close Detection

Connector

Signal

1 Signal

2 GND

P/N：220010423-G

Appendix A

CN3 Output Signal TTL/RS232/RS485/cctalk Jumper Configuration

Default configuration of COM-5 and COM-6 are RS-232 mode.

 Locations:

 CN3 (COM-5) selectable functions

RS-232

(Default) TTL RS-485 ccTalk

Note: Orange block means shorted by a jumper, and others leave it N.C.

 CN3 (COM-6) selectable functions

RS-232

(Default) TTL RS-485 ccTalk

Note: Orange block means shorted by a jumper, and others leave it N.C.

P/N：220010423-G

Appendix B

AGC I/O Definition

I : Input I.I: Input with isolation

O.C: Open-Collector Output I/O: Spare Input/Output

Connectors Map

AGC

Channel

I/O

Type

Functions Rear panel

Gaming I/O Onboard Remark

DI0 I Door SW1 CN7 – Pin1 AGA log 0

DI1 I Door SW2 CN7 – Pin2

AGA log 1

DI2 I Door SW3 CN7 – Pin3

AGA log 2

DI3 I Door SW4 CN7 – Pin4

AGA log 3

DI4 I Door SW5 CN7 – Pin5

AGA log 4

DI5 I Door SW6 CASESW1

AGA log 8 ; Onboard chassis Switch

DI6 I Door SW7 CASESW2

AGA log 9 ; Onboard JST 2.0mm

connector for ext. switch.

DI7 I.I Button 1 CN7 – Pin6

DI8 I.I Button 2 CN7 – Pin7

DI9 I.I Button 3 CN7 – Pin8

DI10 I.I Button 4 CN7 – Pin9

DI11 I.I Button 5 CN7 – Pin10

DI12 I.I Button 6 CN7 – Pin11

DI13 I.I Button 7 CN7 – Pin12

DI14 I.I Button 8 CN7 – Pin13

DI15 I.I Button 9 CN7 – Pin14

DI16 I.I Button 10 CN7 – Pin15

DI17 I.I Button 11 CN7 – Pin16

DI18 I.I Button 12 CN6 – Pin1

DI19 I.I Button 13 CN6 – Pin2

DI20 I.I Button 14 CN6 – Pin3

DI21 I.I Button 15 CN6 – Pin4

DI22 I.I Button 16 CN6 – Pin5

DI23 I.I Dissolve Key-Lock

(Key 1) CN6 – Pin6

DI24 I.I OM Key-Lock

(Key 2) CN6 – Pin7

DI25 I.I Setup Key-Lock

(Hand Pay) (Key 3) CN6 – Pin8

DI26 I.I Touch-Cal Key-Lock

(Key 4) CN6 – Pin9

DI27 I.I Spare Key-Lock

(Key 5) CN6 – Pin10

DI28 I.I Coin-In Signal A CN6 – Pin11

AGC Counter 1

DI29 I.I Coin-In Signal B CN6 – Pin12

AGC Counter 2

DI30 I.I Bill-In CN6 – Pin13

AGC Counter 3

DI31 I.I Hopper Sensor CN6 – Pin14

AGC Counter 4

DI32 I.I General Purpose In 0 CN6 – Pin15

DI33 I.I General Purpose In 1 CN6 – Pin16

P/N：220010423-G

Connectors Map

AGC

Channel

I/O

Type

Functions Rear panel

Gaming I/O Onboard Remark

DI34 I DIP Switch S1 SW1 –S1

DI35 I DIP Switch S2 SW1 –S2

DI36 I DIP Switch S3 SW1 –S3

DI37 I DIP Switch S4 SW1 –S4

DI38 I DIP Switch S5 SW1 –S5

DI39 I DIP Switch S6 SW1 –S6

DI40 I DIP Switch S7 SW1 –S7

DI41 I DIP Switch S8 SW1 –S8

DO0 O.C.

Lamp1 CN4 – Pin1 500mA

(max)

current

DO1 O.C.

Lamp2 CN4 – Pin2

500mA

(max)

current

DO2 O.C.

Lamp3 CN4 – Pin3

500mA

(max)

current

DO3 O.C.

Lamp4 CN4 – Pin4

500mA

(max)

current

DO4 O.C.

Lamp5 CN4 – Pin5

500mA

(max)

current

DO5 O.C.

Lamp6 CN4 – Pin6

500mA

(max)

current

DO6 O.C.

Lamp7 CN4 – Pin7

500mA

(max)

current

DO7 O.C.

Lamp8 CN4 – Pin8

500mA

(max)

current

DO8 O.C.

Lamp9 CN4 – Pin11

500mA

(max)

current

DO9 O.C.

Lamp10 CN4 – Pin12

500mA

(max)

current

DO10 O.C.

Lamp11 CN4 – Pin13

500mA

(max)

current

DO11 O.C.

Lamp12 CN4 – Pin14

500mA

(max)

current

DO12 O.C.

Lamp13 CN4 – Pin15

500mA

(max)

current

DO13 O.C.

Lamp14 CN4 – Pin16

(max)

current

DO14 O.C.

Lamp15 CN4 – Pin17

(max)

current

DO15 O.C.

Lamp16 CN4 – Pin18

(max)

current

DO16 O.C.

Key-In Meter

(Meter 1) CN5 – Pin1 AGC Pulse Generator 1

DO17 O.C.

Bill-In Meter

(Meter 2) CN5 – Pin2 AGC Pulse Generator 2

DO18 O.C.

Coin-In Meter

(Meter 3) CN5 – Pin3 AGC Pulse Generator 3

DO19 O.C.

Pay-Out Meter

(Meter 4) CN5 – Pin4 AGC Pulse Generator 4

DO20 O.C.

Key-Out Meter

(Meter 5) CN5 – Pin5 AGC Pulse Generator 5

DO21 O.C.

Hand-Pay Meter1

(Meter 6) CN5 – Pin6 AGC Pulse Generator 6

DO22 O.C.

Hand-Pay Meter2

(Meter 7) CN5 – Pin7 AGC Pulse Generator 7

DO23 O.C.

Spare Meter1

(Meter 8) CN5 – Pin8 AGC Pulse Generator 8

DO24 O.C.

Coin-Enable CN5 – Pin11

DO25 O.C.

Bill-Enable CN5 – Pin12

DO26 O.C.

Hopper SSR CN5 – Pin13

DO27 O.C.

General Purpose Out 0

CN5 – Pin14

DO28 O.C.

General Purpose Out 1

CN5 – Pin15

DO29 O.C.

General Purpose Out 2

CN5 – Pin16

DO30 O.C.

General Purpose Out 3

CN5 – Pin17

DO31 O.C.

General Purpose Out 4

CN5 – Pin18

P/N：220010423-G

Connectors Map

AGC

Channel

I/O

Type

Functions Rear panel

Gaming I/O Onboard Remark

GPIO0 I/O Spare I/O bit 0 SPAREIO1

– Pin1

GPIO1 I/O Spare I/O bit 1 SPAREIO1

– Pin2

GPIO2 I/O Spare I/O bit 2 SPAREIO1

– Pin3

GPIO3 I/O Spare I/O bit 3 SPAREIO1

– Pin4

GPIO4 I/O Spare I/O bit 4 SPAREIO1

– Pin5

GPIO5 I/O Spare I/O bit 5 SPAREIO1

– Pin6

GPIO6 I/O Spare I/O bit 6 SPAREIO1

– Pin7

GPIO7 I/O Spare I/O bit 7 SPAREIO1

– Pin8

GPIO8 I/O Spare I/O bit 8 SPAREIO1

– Pin9

GPIO9 I/O Spare I/O bit 9

SPAREIO1

– Pin10

GPIO10

I/O Spare I/O bit 10

SPAREIO1

– Pin11

GPIO11

I/O Spare I/O bit 11

SPAREIO1

– Pin12

GPIO12

I/O Spare I/O bit 12

SPAREIO1

– Pin13

GPIO13

I/O Spare I/O bit 13

SPAREIO1

– Pin14

GPIO14

I/O Spare I/O bit 14

SPAREIO1

– Pin15

GPIO15

I/O Spare I/O bit 15

SPAREIO1

– Pin16

Other manuals for ACE-B7400

Table of contents

Other Acrosser Technology Motherboard manuals

Acrosser Technology

Acrosser Technology AR-B1476 User manual

Acrosser Technology

Acrosser Technology AMB-IH61T3 User manual

Acrosser Technology

Acrosser Technology AR-B5800 Installation guide

Acrosser Technology

Acrosser Technology AR-B5800A Installation guide

Acrosser Technology

Acrosser Technology AR-B1631 User manual

Acrosser Technology

Acrosser Technology AMB-D255T1 Installation guide

Acrosser Technology

Acrosser Technology AR-B9012-G User manual

Acrosser Technology

Acrosser Technology AR-B104D Installation guide

Acrosser Technology

Acrosser Technology AR-B1551 User manual

Acrosser Technology

Acrosser Technology ACS-B1086 User manual

Acrosser Technology

Acrosser Technology AR-B1893A User manual

Acrosser Technology

Acrosser Technology AR-B1894 User manual

Acrosser Technology

Acrosser Technology AR-B1666A User manual

Acrosser Technology

Acrosser Technology AR-B104D Installation guide

Acrosser Technology

Acrosser Technology AR-B1665 User manual

Acrosser Technology

Acrosser Technology AR-B1893 User manual

Acrosser Technology

Acrosser Technology AR-B6051 Installation guide

Acrosser Technology

Acrosser Technology AR-B1653 User manual

Acrosser Technology

Acrosser Technology AR-B6002 Installation guide

Acrosser Technology

Acrosser Technology AR-B5205 Series Installation guide

Acrosser Technology

Acrosser Technology AR-B6003 User manual

Acrosser Technology

Acrosser Technology AR-K0006 User manual

Acrosser Technology

Acrosser Technology AR-B5891 User manual

Acrosser Technology

Acrosser Technology AR-B1554A User manual

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual