Abocom SW2400M User manual

Table of contents

Other Abocom Network Router manuals

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview

M73-APO07-460

24-PortFastEthernetSwitch

QuickInstallationGuide

FCC REGULATORY STATEMENTS

FCC Certification, Part15, Class A

This equipment has been tested and found to comply with the limits for a class A Digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and usedin accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

CE Mark Warning

This is a Class Aproduct. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures

-1-

INTRODUCTION

The 24-Port Fast Ethernet 10/100Mbps N-Way Switch provides you a flexible, reliable,

and affordable solution for an Ethernet network. It comes with twenty-four independent

10BASE-T/100BASE-TX ports. Each port delivers up to 200Mbps throughput, and is

able to operate in either half or full-duplex modes.

The 24-Port Fast Ethernet 10/100Mbps N-Way Switch also possesses a N-Way auto-

negotiation function, which automatically adjusts the device for optimum operation.

“Store-and-Forward” architecture filters eliminate error packets and improve efficiency.

Plus, based on Auto-MDI/MDIX technology, you are able to use either a straight through

or a crossover Ethernet cable to connect with other devices. Moreover, the built-in

Universal Power Supply allows you to install the switch easily without any external

power adapter.

Key Features

•Complies with IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX standards

•Supports twenty four 10M/100M auto-detect Half/Full duplex switch ports

•Supports 802.3x Flow Control pause packet for Full Duplex in case buffer is full

•Supports Back Pressure function for Half Duplex operation in case buffer is full

•All ports support Auto-negotiation

•Supports source/ destination MAC address lookup and aging with 8K MAC address

(4K entries each entry table)

•Store-and-Forward switching operation

•No-head-of-line blocking system support

•Broadcast storm prevention

•Built in Universal Power Supply: 90~264V

•Emission certification: FCC Class A, CE mark

-2-

PARTS NAMES AND FUNCTIONS

Front Panel: LED Indicators

Status

LED Color Solid Flashing

Power Green Becomes

solid green when power is

turned on. N/A

LINK/ACT

Green Successful connection

Sending or Receiving

packets

Rear Panel: Power Port

-3-

HARDWARE INSTALLATION

The switch is considered as a “plug and play” network device and requires no special

setup procedures. Connect the power cord and cables correctly and you are ready to go.

Switch installation

1. Put the switch on the appropriate location. When you install the switch, there are

two things needed to be considered:

ŸLocation: Your switch should be located in a place that is central to your

home/office space and allows all computers and networked devices connected to

your switch.

ŸPower: Remember to locate your switch near electrical outlet.

2. Power on the switch by connecting the power cord.

3. Verify if the power (POWER) LED is on. If the POWER LED does not light up,

check the power cord and power outlet to verify its connection. If it still remains

unlit, please contact your dealer for support.

Ethernet Port Connection

Connect user machines, servers, another switch, hub, or any other devices to the Ethernet

ports on this switch with either straight through or crossover Ethernet cables.

-4-

SPECIFICATION

Standards IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE802.3x Flow Control

Protocol CSMA/CD

Ports Twenty four 10/100Mbps RJ-

45 Ports (support

Auto-MDI/MDIX)

Switching Scheme

Store-and-Forward

Flow control Full Duplex: IEEE802.3x

Half Duplex: Back Pressure

Cabling type UTP Category 3 or better (10Base-T)

UTP Category 5 or better (100Base-TX)

MAC Address 8K

LED indicators Power Green

Link/Act Green: on for successful connection,

flashing for activity

Physical

Dimension 438 x 184 x 44mm3(Width x Depth x Height)

Weight 1.9 kg

Input power

specifications AC 90~264V, 50~60Hz

Power

Consumption 5.3 W

Agency and

Regulatory FCC Class A, CE mark

Operating

Temperature 0°C to 40°C

Operating Humidity

5~90% non-condensing