ABB TZIDC-110 How to use

TZID-C110 Intelligent positioner for

PROFIBUS PA

Short manual 41/18-77 EN Rev. 01

TZID-C110 Intelligent positioner for PROFIBUS PA

for PA Profile V3.0

Short manual

Document No. 41/18-77 EN

Issue date 07.02

Revision 01

Manufacturer:

ABB Automation Products GmbH

Schillerstrasse 72

32425 Minden

GERMANY

Tel: +49 571 830-1494

Fax: +49 571 830-1860

Mail: actuate.deapr@de.abb.com

Note:

This document is a short manual providing the essential information needed for mounting

and commissioning the TZID-C110 positioner. For details on other subjects like configuration,

operation and ordering details please refer to Data sheet 10/18-0.23 EN or the Operating

manual (CD version) 42/18-74 EN.

Subject to changes without notice.

This technical documentation is protected by copyright. Translating, photocopying and dissem-

inating it in any form whatsoever - even editings or excerpts thereof - especially as reprint, pho-

tomechanical or electronic reproduction or storage on data processing systems or networks is

not allowed without the permission of the copyright owner and non-compliance will lead to both

civil and criminal prosecution.

Table of contents

41/18-77 EN Table of contents i

Table of contents

1 Safety and precautions .............................................................................................. 1

1.1 General ......................................................................................................................1

1.2 Explanation of warning signs and notes................................................................2

1.3 Notes on electrical and pneumatic safety .............................................................2

1.4 Proper use.................................................................................................................2

1.5 Qualified personnel ..................................................................................................3

2 Manufacturer’s information...................................................................................... 3

2.1 Delivery......................................................................................................................3

2.2 CE compliance information .....................................................................................3

3 Installing and commissioning ................................................................................. 4

3.1 Mechanical mounting...............................................................................................4

3.1.1 General........................................................................................................... 4

3.1.2 Operating conditions at the installation site ................................................... 5

3.1.3 Mounting to linear actuators ........................................................................... 5

3.1.4 Mounting the positioner to rotary actuators .................................................. 10

3.2 Pneumatic connection. ..........................................................................................13

3.2.1 Safety instructions ........................................................................................ 13

3.2.2 Making the pneumatic connection ................................................................ 14

3.2.3 Mounting the splash guard cap..................................................................... 15

3.3 Electrical connection..............................................................................................16

3.3.1 Safety instructions ........................................................................................ 16

3.3.2 Overview....................................................................................................... 17

3.3.3 Making the connections................................................................................ 18

Table of contents

ii Table of contents 41/18-77 EN

3.4 Commissioning.......................................................................................................19

3.4.1 Commissioning procedure............................................................................ 19

3.4.2 Setting the bus address................................................................................ 20

3.4.3 Overview of the operating modes and how to select (from operating level) . 21

3.4.4 Parameter setting example:.......................................................................... 22

4 Technical data ............................................................................................................. 24

4.1 Basic model.............................................................................................................24

4.2 Options ....................................................................................................................28

5 Certificates....................................................................................................................29

Appendix A: Configuration overview ........................................................................A

Safety and precautions

41/18-77 EN Safety and precautions 1

1 Safety and precautions

1.1 General

Proper and safe operation of the TZID-C110 positioner requires:

• proper transportation and storage

• installation and commissioning by qualified

personnel

• correct operation according to the instructions in this manual

• proper use (see chapter 1.4 on page 2)

• careful maintenance

Only qualified personnel are allowed to work on the device (see chapter 1.5 on page 3).

Observe

• the present operating instructions

• the relevant safety regulations and standards for the installation and operation of

electrical systems

• the standards, regulations and directives governing explosion protection, when using

intrinsically safe devices

The regulations, standards and directives referred to in these operating instructions are

applicable in Germany. When using the TZID-C110 positioner outside the German Fed-

eral jurisdiction, the relevant regulations, standards and directives applicable in the coun-

try where the device is used must be observed.

The TZID-C110 positioner has been designed and tested in accordance with DIN VDE

0411 Part 1.

Safety Requirements for Electronic Measuring Apparatuses

(based on IEC Publication 348) and has been supplied in a safe condition.

The present operating instructions contain warnings and cautions marked with a symbol

(see chapter 1.2). The instructions given in these sections must be observed to retain the

device in a safe condition and to ensure safe operation. Otherwise, persons can be

endangered or the device itself or other devices or equipment may be damaged or fail.

Important instructions for your safety!

Read and observe!

Caution

Safety and precautions

2 Safety and precautions 41/18-77 EN

1.2 Explanation of warning signs and notes

Important information has been marked and emphasized with the following symbols in

these operating instructions:

1.3 Notes on electrical and pneumatic safety

1.4 Proper use

The TZID-C110 positioner is an electro-pneumatic valve positioner for use with pneu-

matic linear and rotary actuators.

The device may only be used for the applications listed in these operating instructions

and in the relevant data sheet (if available).

This symbol is printed next to warnings indicating a direct endangerment of a

person’s health or life. Also, major property damage may occur.

Warning

If the safety notes marked with this symbol are not observed, minor personal

injuries and property damage may result.

Caution

This symbol is printed next to notes containing important informationen pertai-

ning to your TZID-C110 or its operation.

•Only qualified persons may mount, electrically and pneumatically connect,

and commission the TZID-C110 positioner.

•Ensure the electrical safety of all feeding devices.

•When connecting the electrical wiring, observe the specifications according

to chapter 4 "Technical data".

•For the electrical installation of ex-protected devices, observe all national

regulations, DIN/VDE directives, especially VDE 0165, the directives for

explosion protection, and the specifications in the EC type examination cer-

tificates (see chapter “Certificates”on page 29 of this manual).

•Do not use the internal communication interfaces LKS or X5 on the printed

circuit board if the positioner is installed in the hazardous area.

•Observe the safety instructions of the pneumatic actuators when mounting

and commissioning the devices. There is danger of injuries due to the high

displacement forces of the actuators.

Warning

Manufacturer’s information

41/18-77 EN Manufacturer’s information 3

1.5 Qualified personnel

Only those persons familiar with the installation, commissioning, operation and mainte-

nance of the TZID-C110 positioner or similar instruments and who have the required

qualification are authorized to work on the device.

These persons are:

•Project specialists who are familiar with the security concepts of process automation.

•Commissioning and service personnel, i.e. persons who have been trained ade-

quately to mount, commission, repair, and maintain the TZID-C110 positioner or sim-

ilar automation instruments or who are –according to safety standards and

guidelines –permitted to commission, ground, and label electrical circuitry, devices,

and systems.

•Operating personnel who is familiar with handling automation equipment and with the

contents of these operating instructions and the instructions in the operating manual

42/18-74 EN.

2 Manufacturer’s information

2.1 Delivery

When receiving the delivery please immediately check items and scope for damages and

completeness. The scope of delivery is stated in the shipping documents. If ordered, the

accessories (e.g. mounting material, pressure gauge block, filter regulator) are added to

the delivery as individual items. Check items and scope of the delivery by means of the

catalog numbers to see if types and quantities are in accordance with your order.

If the positioner is delivered already mounted to the actuator, the positioner, accessories,

and actuator are considered as a common delivery item.

A list of catalog numbers and details of the different versions and accessories can be

found in data sheet 10/18-0.23 EN.

2.2 CE compliance information

We declare that we are the manufacturer of the TZID-C110 positioner and that the prod-

uct conforms with the regulations listed below and meets the following requirements of

EC regulation 89/336/CEE as of May 1989:

Basic technical standards/product standards

RFI suppression EN 55022 as of May 1995

EN 50081-1 as of March 1993

EMI/RFI shielding EN 50082-1 as of March 1993

The TZID-C110 positioner meets the EC regulation for CE conformity.

Installing and commissioning

4 Installing and commissioning 41/18-77 EN

3 Installing and commissioning

3.1 Mechanical mounting

3.1.1 General

The arrow (1) on the feedback

shaft (and thus the lever) must

travel within the area marked with

the small arrows (2).

When mounting,

ensure that the

transfer of the

stroke or rotation

angle for the posi-

tion feedback is

correct. The maxi-

mum rotation

angle is 60°for

mounting to linear

actuators and

120°for mounting

to rotary actua-

tors. The mini-

mum range for

both applications

is 25°.

Fig. 1 Operating range

TZID-C

+60°

-60°

+30°

-30°

100%

Sensor range for rotary actuators

Stroke range

Valve range

Sensor range for linear actuators

Fig. 2 Positioner ranges

Installing and commissioning

41/18-77 EN Installing and commissioning 5

3.1.2 Operating conditions at the installation site

Ambient temperature: -40 ... +85 °C (-40 ... +185 °F)

Relative humidity < 75% (95% for a short time), non-condensing

Observe the specifications for protection class

IP65 / NEMA 4X

Explosion protection: Observe the specifications in the certificate, see section

“Certificates”on page 29.

Mounting position: any orientation allowed, provided that the splash guard

cap is in place, see section “Mounting the splash guard

cap”on page 15.

3.1.3 Mounting to linear actuators

A special attachment kit is available for mounting the positioner to a linear actuator

according to DIN/IEC 534 (lateral mounting to NAMUR) comprising the following parts:

Tools required: Wrench 10 mm/13 mm

Allen key 4 mm

•Lever (1.0) w. follower

pin, for 10...35 mm or

25...90 mm actuator

stroke

•Follower guide (2.0)

with two screws (2.1)

and clamp plates (2.2)

•Angle bracket (3.0)

with two screws (3.1),

two spring washers

(3.2), and two plain

washers (3.3)

•Screw (3.4) and plain

washer (3.5) for

mounting to cast iron

yoke

•Two U-bolts (3.7),

each with two nuts

(3.8), two spring

washers (3.9), and

two plain washers

(3.10) for mounting to

columnar yoke

Before installing check to ensure that the specifications in terms of safety

and control applicable to the TZID-C110 will not be exceeded.

Warning

3.4

3.5

3.7

3.10

3.8

3.1 3.2 3.3

3.0

2.1

2.2

2.0

1.0

3.9

Installing and commissioning

6 Installing and commissioning 41/18-77 EN

1. Mount the follower guide to the actuator

2. Assemble the lever (if not yet pre-assembled)

•Fasten the follower guide (1)

and the clamp plates (2) with

screws (3) to the spindle of the

actuator; hand-tighten the

screws.

•Slip the spring (2) onto the bolt

with the follower pin (1).

•Slip the plastic washer (3) onto

the bolt and compress the

spring with it.

•Insert the bolt with com-

pressed spring into the oblong

hole in the lever (4) and fasten it

in the desired position using the

plain washer (5) and nut (6) at

the lever; the scale on the lever

indicates the link point for the

stroke range.

•Slip the plain washer (8) onto

the screw (7), insert the screw

into the lever and counter with

the nut (9).

Other manuals for TZIDC-110

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide