ZKTeco C3 User manual
ZK Access Quick Start Guide
Install C3 using TCP/IPmode of communication
C3 controller supports the connection from panel to server over RS485 data line and also via
nodes on TCP/IP Ethernet networks. This greatly increases the flexibility of installation options.
Note: Make sure the devices are in the same LAN network with server or directly connect to the
server using the TCP/IP communication.
TCP/IP Connection Cable Mode
There are two ways to connect to C3 controller.
○
1Network cable directly connects Management host and the device, without a hub.
○
2In a large office a hub/switch is needed to connect more than 2 devices.
The configuration is as follows:
TCP/IP Communication
How to add a device into ZKAccess software?
ZKAccess provides two ways to add a device.
○
1When the IP address of the device is already known, you can quickly add it by entering
the IP address as follow:
Click [Add] on the [Device-Device] interface.
ZK Access Quick Start Guide
As the interface appears, write the [Device Name], then give the [IP address] of the device. The
[IP Port No.] is defaulted to 4370 by the system. Please set the password if needed.
Note: Select the type of the device. If it is a Four-Door-One-Way Access Control Panel there will
appear an extra option-[Switch to Two-door Two-way]. Select as appropriate according to
the actual device.
Select the [Area] the device belongs to. If you do not want to clear the data (Information in Time
zones, Access Levels, etc.) in the device when adding, remove the check beside the [Clear Data in
the Device when adding] option. Click [OK] to add the device.
○
2Click [SearchAccess Control Panels] option on the [Device-Device] interface.
Click [Search], after searching, the usable device will show in the results list. Modify the IP
address to available IP, and then add the device.
ZK Access Quick Start Guide
Using fast search tool to modify the IPaddress of a device
ZK provides a fast search tool for searching devices and modifying the IP addresses. This allows
devices to be added directly without modifying the system, which is inconvenient and time
consuming.
The tool and the operation of searching and modifying are as follows:
Click [Search Panel] on the [Setting] dropdown menu.
After a few seconds results for the usable devices will appear.
Click to select the device and [Modify IPAddress] on the [Setting] dropdown menu to modify the
IP address of the devices.
Table of contents
Other ZKTeco IP Access Controllers manuals
ZKTeco
ZKTeco MultiBio 700 User manual
ZKTeco
ZKTeco F19 User manual
ZKTeco
ZKTeco White LCD Series User manual
ZKTeco
ZKTeco BioPro SA30 User manual
ZKTeco
ZKTeco Notus User manual
ZKTeco
ZKTeco EFace10 User manual
ZKTeco
ZKTeco SpeedFace V5L QR Series User manual
ZKTeco
ZKTeco ProCapture-T User manual
ZKTeco
ZKTeco ProBio User manual
ZKTeco
ZKTeco Notus User manual
ZKTeco
ZKTeco MB20-VL User manual
ZKTeco
ZKTeco KF1000 Series User manual
ZKTeco
ZKTeco F6 User manual
ZKTeco
ZKTeco F17 User manual
ZKTeco
ZKTeco PA10 User manual
ZKTeco
ZKTeco F18 User manual
ZKTeco
ZKTeco X8-BT User manual
ZKTeco
ZKTeco ProMA Series User manual
![ZKTeco G4[QR] User manual](/data/manuals/1j/2/1j2wo/sources/zkteco-g4-qr-ip-access-controllers-manual.jpg "ZKTeco G4[QR] User manual")
ZKTeco
ZKTeco G4[QR] User manual
ZKTeco
ZKTeco FaceKiosk-H10A User manual
