ZKTeco FaceDepot-7BL User manual
Version: 1.1
Date: December 2019
Quick Start Guide
FaceDepot 7BL-
Power
GND
+12V
Overview
Flash
Camera
7 inch touch screen
Microphone
Fingerprint sensor
Card reading area
Magnetic
tamper switch
Speaker
FP & RFID Reader (Optional)
Connection
interface
Lock
AUX
Alarm
Exit
Button
Sensor
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
Auxiliary
input
Wiegand
In
Wiegand
Out
+12V
GND
INWD0
INWD1
W0D
W1D
RS232
RS485
12V
485A
GND
TXD1
RXD1
GND
TXD2
RXD2
RS232
485B
Connection interface
Reset
USB port
Network
interface
1
Device Installation
1.5m
123
①Attach the mounting template sticker to the wall, and drill holes according to
the mounting paper. Fix the back plate on the wall using wall mounting screws.
②Attach the device to the back plate.
③Fasten the device to the back plate with a security screw.
Method 1: Installation on the wall
Please route the wire through the bracket before installation.
1. Drill a hole on the barrier gate.
Insert the bracket into the hole and fix it with a nut.2.
3. Adjust the angle of the device.
Method 2: Install on the barrier gate
Adjust the device
1. Adjust the angle of the device.
2. Fix the screws.
Note: If you want to install FP & RFID reader, please insert the reader after step .①
2
TCP/IP
Alarm
Smoke
detector
Lock
Exit Button
Door Sensor
Card
Reader
ZKBioSecurity
Standalone Installation
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
+
-
Door Sensor, Exit Button & Alarm Connection
Door Sensor
Alarm
Alarm's power switch
Exit Button
Smoke detector
Note: On this document, we just guide you to connect some normal components,
if you want more connection of SRB, external fingerprint reader and so on, please
check user manual document.
+
-
-
+
+
-
3
Lock Relay Connection
Wiegand Reader Connection
The system supports Normally Opened Lock and Normally Closed Lock.
F 107R
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
The NO LOCK (normally opened at power on) is connected with 'NO' and 'COM'
terminals, and the NC LOCK (normally closed at power on) is connected with 'NC'
and 'COM' terminals. T NC Lock below:ake as an example
Normally Closed Lock
1) Device not sharing power with the lock 2) Device sharing power with the lock
WD0
WD1
+12V
GND
Wiegand Reader
+12V
IDW1
IDW0
GND
WD0
WD1
Access controller
GND
12V
DC12V
DC12V
F 107R
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
Normally Closed Lock
GND
12V
DC12V
4
Barrier Connection
Ethernet Connection
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Click [COMM.] > [Ethernet] > [IP Address], input the IP address and click [OK].
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
8
7
6RJ 45
5
4
3
2
1
Note: In LAN, IP addresses of the server (PC) and the device must be in the same
network segment when connecting to ZKBioSecurity software.
Barrier gate
ZKBioSecurity
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
GND
K1
5
User Registration
GND
12V DC
Recommended power supply
1) 12V ± 10%, at least 00mA.30
2) To share the power with other devices, use a power
supply with higher current ratings.
Power Connection
When there is no super administrator set in the device, click on to enter the menu.
After setting the super administrator, the system will request for the administrator’s
verification before entering the menu. For the security purpose, it is recommended to
register a super administrator at the first time you use the device.
Method1: Register on the device
Click on > >[User Mgt.] [New User] to register a new user. Settings include
entering user ID and name, registering a fingerprint, face, password, badge (optional)
and user photo, setting user role and access control role.
6
L
LL
Method2: Register on ZKBioSecurity software
Please set the IP address and cloud service server address on the device.
1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to
the software.
When the device has set the server address and port, it can be added automatically.
7
2. Click [Personnel] > [Person] > [New] to register users in the software.
3. Add users to access levels.
4. Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices].
For more details, please refer to the ZKBioSecurity User Manual.
Step 1
Step 2
Step 3
Step 4
Method3: Register on the phone
Once ZKBioSecurity software installation, users could enroll face via browser
application on their own mobile phone.
1. Click [Personnel] > [Parameters], input ‘’http://Server address:Port’’ in the QR Code
UGL bar. The software will automatically generates a QR code. Scan the QR code or
login onto‘’http://Server address:Port/app/v1/adreg’’ by the mobile phone to register
users.
8
2. The users will display in [Personnel] > [Temporary Personnel], click [Review].
Ethernet and Cloud Server Settings
Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP
communication of the device is successful, the icon will be displayed in the
upper right corner of the standby interface.
Click on > [COMM.] > [Cloud Server Setting] to set the server address and server
port, that is, the IP address and port number of the server after the software is
installed. If the device communicates with the server successfully, the icon will be
displayed in the upper right corner of the standby interface.
9
Other manuals for FaceDepot-7BL
2
Table of contents
Other ZKTeco IP Access Controllers manuals
ZKTeco
ZKTeco C5S120 Guide
ZKTeco
ZKTeco MB20-VL User manual
ZKTeco
ZKTeco ZKX Series User manual
ZKTeco
ZKTeco SilkID F21-ID User manual
ZKTeco
ZKTeco Green Label ProFace X User manual
ZKTeco
ZKTeco ProlD Series User manual
ZKTeco
ZKTeco F18 User manual
ZKTeco
ZKTeco C2-260/inBio2-260 User manual
ZKTeco
ZKTeco BioServer 2 User manual
ZKTeco
ZKTeco ZPad Plus User manual
ZKTeco
ZKTeco Horus User manual
ZKTeco
ZKTeco IN710 User manual
ZKTeco
ZKTeco SpeedFace M1 User manual
ZKTeco
ZKTeco F18I User manual
ZKTeco
ZKTeco Green Label ProCapture-T User manual
ZKTeco
ZKTeco C2-260 User manual
ZKTeco
ZKTeco BR1200 Series User manual
ZKTeco
ZKTeco ProFace X SL User manual
ZKTeco
ZKTeco SC800 User manual
ZKTeco
ZKTeco C3 Pro User manual
