YESOUL V1 User manual
V1 Product Manual
Product model: YS-003
Before using this product,
carefully read
and properly keep this manual.
V1
YESOUL BIKE
YESOUL BIKE
Product Parameters
YESOUL BIKE V1
Supporting software version
Resistance system
Drive mode
Power supply
Height limit
Rated maximum load
Net weight
Gross weight
Overall dimensions
Maximum tablet width: 260mm
iOS 10.0 or higher, Android 5.0 or higher
Magnetron resistance system
Belt drive
Button battery (model: CR2477)
150~195cm
120kg
45 kg
48 kg
(Length) 1450mm x (Width) 530mm x (Height) 1300 mm
Tablet (mobile phone) holder
size
Important Safety Instructions
Please read them carefully. Improper use may result in
personal injury or death!
1.Make sure that the saddle height adjustment knob is secured correctly, and will not affect
motion during exercise.
2.Keep children and pets away from this product. This product is for those over 16 years old only.
3.Never stretch any object or body part into the openings of the bike.
4.The weight of the user must not exceed the maximum load.
5.Get off the bike until flywheel and pedals stop rotating. Otherwise, severe injuries may be
caused due to control failure.
6.If you feel any discomfort, such as dizziness or breathing difficulty, stop riding the bike and
carefully get off.
7.Never turn pedals by hand or touch any rotating mechanical part; otherwise, personal injury
may be caused.
8.Keep the body hydrated as needed during riding.
9.Use this product according to the instructions in this manual. Warm up fully before exercise.
10.Without the preliminary determination of baseline fitness level and medical certificate signed
by a doctor, never be engaged in high-speed or high-intensity sports. Before attempting any
high-intensity short sprints, pay attention to the body state and posture, and apply a
controllable speed.
11.Wear professional cycling clothes or tight-fitting sportswear and sports shoes, and tighten
foot straps to avoid injury caused by pulling or entanglement by this product.
12.Never use this product with inappropriate shoes or barefoot.
13.Incorrect or excessive training may cause injury.
14.Check whether the bike for loosening or damage before each use.
15.Never refit this bike or use non-original accessories without permission. The casing must be
opened by professionals, in order to avoid damage.
16.Those pregnant or with high blood pressure, heart disease, lumbar spondylosis or reduced
mobility must not use this product without the permission of doctors.
17.In case of any discomfort such as dizziness or chest pain during exercise, stop exercising
immediately and go to a hospital for examination.
18.If the product fails, immediately stop using it.
19.This product must not be used for medical rehabilitation.
20.Use this product on a flat and clean ground.
21.Carry out preventive maintenance regularly.
22.Never expose this product in a humid place. This product must not be used outdoor or in any
humid place.
Installation Guide - List of Parts
STEP 1: Check of parts
List of Parts
Parts List (Components List)
NO. Name
Front ground pipe
assembly
Rear ground pipe
assembly
Handle
Elastic washer
8*2.1t
Flat washer M8
(D16×d8.5×1.5t)
Hexagon socket
button head screw
M8*P1.25*16L
Screen bracket
Hexagon socket
button head screw
M8*P1.25*50L
Quantity Picture
Bottle holder
Hexagon socket
button head screw
M6*P1.0*10L
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
1
1
4
6
4
1
6
1
1
2
Installation Guide - List of Parts
Parts List (Components List)
Tablet (mobile
phone) holder
Hexagon socket
cap screwM6*P1.0*
12LM6*P1.0*12L
Pedal set left/right
Dumbbell set
(1kg/EA)
NO. Name Quantity Picture
Elastic washer
6*1.6t
Accessories List (Tools List)
Hex key
4mm/70LX25L
Hex key
5mm/100LX30L
Box-ended wrench
8/10mm
Box-ended wrench
13/14/15/17 mm
NO. Name Quantity Picture
(L) (R)
*In order to facilitate assembly, some accessories have been installed on the body before
delivery.
⑪
⑫
⑬
⑭
⑮
1
2
1
2
2
1
1
1
1
A
B
C
D
③
⑤
①
Installation Guide
STEP 2: Install ground pipes
1.Install the front ground pipe assembly ①, and tighten it with the hex key (B), as shown in the figure.
2.Lock it with two sets of hexagon socket button head screw ③ and flat washer ⑤ as shown in the
figure, make sure to lock the pipe tightly; otherwise, it may result in deformation.
3.Check and confirm the adjusting footpad is fully locked into the front ground pipe assembly .
1.Install the rear ground pipe assembly ②, and tighten it with the hex key (B), as shown in the figure.
2.Lock it with two sets of hexagon socket button head screw ③ and flat washer ⑤ as shown in the
figure, make sure to lock the pipe tightly; otherwise, it may result in deformation.
3.Check and confirm the adjusting footpad is fully locked into the rear ground pipe assembly .
③
⑤
②
⑥
④
⑦
④
⑧
⑦
Installation Guide
STEP 3: Assemble handle
Load the screen bracket ⑧ onto the fixed seat, and lock the same onto the stand column with 2 sets
of hexagon socket button head screws ⑦ and elastic washers④ via the hex key (B).
Place the handle ⑥ on the handle bracket, and lock the same with 4 sets of elastic washers ④ and
hexagon socket button head screws ⑦ via the hex key (B).
⑧
⑨
⑩
⑪
⑫
⑮
⑮
⑫
Installation Guide
STEP 4: Install bottle holder
STEP 5: Installation of tablet (mobile phone) holder
Take out the PAD (cellphone) holder ⑪, align the support on the back of the holder with the screen
bracket, lock two sets of elastic washer ⑮ and hexagon socket screw ⑫ on the bracket via the hex
key (B).
As shown in the figure, clip the bottle holder⑨ by the middle under the screen bracket ⑧, and lock
the same onto the bracket with 2 sets of Hex socket screws⑩.
R pedal assembly ⑬ L pedal assembly ⑬
Installation Guide
STEP 6: Pedal installation
Wrench (D)
Screw the pedal into the crank manually first, and
then tighten the left/right pedal assembly ⑬ with the
box-ended wrench (D). (Note: The tightening
directions for both the left pedal and the right pedal
are towards the head direction.)
Safety tips:
Reverse riding is not recommended, as it is likely to loosen pedals. After reverse riding, check
whether the pedals are locked, in order to avoid safety issues arising from loose pedals.
1.Take out the pedal assembly ⑬.
2.Pay attention to distinguish left pedal and right pedal.
3.Lock the left pedal assembly ⑬ into the left crank, and tighten with the box-ended wrench (D)
along the direction indicated by the arrow.
4.Lock the right pedal assembly ⑬ into the right crank, and tighten with the box-ended wrench (D)
along the direction indicated by the arrow.
8
STEP 7: Battery Dismantling and Installation
1.If the bike is provided with a battery, pull the insulation strip out of the gap of the battery cover
before using this product.
2.When battery replacement is required, remove the two cruciform slot screws on the electronic
control plate, and pull out the plate from the back (do not pull hard for the power cord on the back
are connected to the cycle body), remove the used battery, load the new battery into the battery
holder with the positive pole facing upwards (“+” mark facing upwards), close the cover, and tighten
the screws.
The positive pole of the
battery faces upwards
Installation Guide
This manual suits for next models
1
Table of contents
Languages:
Other YESOUL Exercise Bike manuals
