YESOUL C1H User manual
C1H Before using this product,
carefully read
and properly keep this manual.
YESOUL Bike
Product model: YS-BC1
C1H Product Manual
YESOUL Bike
YESOUL Bike C1H
Product Parameters
Tablet (mobile phone) holder size
Supporting software version
Resistance system
Drive mode
Power supply
Connection mode of sensing system
Height limit
Rated maximum load
Net weight
Gross weight
Overall dimensions
Maximum tablet width: 10.1-inch
IOS 10.0 or higher, Android 5.0 or higher
Magnetron resistance system
Belt drive
AA battery
Bluetooth
150 ~ 190cm
120kg
30kg
34kg
(Length) 995mm × (Width) 516mm × (Height) 1160mm
Important Safety Instructions
Please read them carefully. Improper use may result in personal
injury or death!
1.Make sure that the saddle height adjustment knob is secured correctly, and will not affect
motion during exercise.
2.Keep children and pets away from this product. This product is for those over 16 years old only.
3.Never stretch any object or body part into the openings of the bike.
4.The weight of the user must not exceed the maximum load.
5.Get off the bike until flywheel and pedals stop rotating. Otherwise, severe injuries may be caused
due to control failure.
6.If you feel any discomfort, such as dizziness or breathing difficulty, stop riding the bike and
carefully get off.
7.Never turn pedals by hand or touch any rotating mechanical part; otherwise, personal injury may
be caused.
8.Keep the body hydrated as needed during riding.
9.Use this product according to the instructions in this manual. Warm up fully before exercise.
10.Without the preliminary determination of baseline fitness level and medical certificate signed
by a doctor, never be engaged in high-speed or high-intensity sports. Before attempting any
high-intensity short sprints, pay attention to the body state and posture, and apply a controllable
speed.
11.Wear professional cycling clothes or tight-fitting sportswear and sports shoes, and tighten foot
straps to avoid injury caused by pulling or entanglement by this product.
12.Never use this product with inappropriate shoes or barefoot.
13.Incorrect or excessive training may cause injury.
14.Check whether the bike for loosening or damage before each use.
15.Never refit this bike or use non-original accessories without permission. The casing must be
opened by professionals, in order to avoid damage.
16.Those pregnant or with high blood pressure, heart disease, lumbar spondylosis or reduced
mobility must not use this product without the permission of doctors.
17.In case of any discomfort such as dizziness or chest pain during exercise, stop exercising
immediately and go to a hospital for examination.
18.If the product fails, immediately stop using it.
19.This product must not be used for medical rehabilitation.
20.Use this product on a flat and clean ground.
21.Carry out preventive maintenance regularly.
22.Never expose this product in a humid place. This product must not be used outdoor or in any
humid place.
23.This product is for household use (Class H) and not medical fitness equipment.
24.Get off the bike or enable the emergency brake until inertia wheel and pedals stop rotating.
Otherwise, severe injuries may be caused due to control failure.
25.Turn the knob to the right end to lock the corresponding component.
26.If used, the screen bracket should be set up at the center to prevent falling.
1
1
1
1
1
1
1
1
⑧
STEP 1: Check of parts
List of Parts
Parts List (Components List)
NO. Name Quantity Picture
②
③
④
①
⑤
⑥
⑦
Installation Guide - List of Parts
Frame
Handlebar assembly
Pedal set left/right
Tablet (mobile phone)
holder
Front tube
Rear tube
Head tube
2×hexagon socket
button head screw
M8×45/washer
2×hexagon socket
button head screw
M8×45/washer
(left) (right)
Mobile phone holder
⑨
⑩
3
1
2
⑪
⑫
⑬
⑭
3
1
1
Seat
⑮
⑯
1
1
Seat post
NO. Name Quantity Diagram
Parts List (Components List)
Washer
Decorative cover
Cross round head self-
drilling screw 4.2×16
Hexagon socket button
head screwM6×30
Hexagon socket button
head screw M8×12
Bottle holder
*In order to facilitate assembly, some accessories have been installed on
the body before delivery.
Installation Guide - List of Parts
D6（D13×d6.5×1.5t）
1
1
1
List of parts
L-type cross head hex
wrench, 6#
Hex wrench, 5#
Open-ended wrench
NO.
A
B
C
Name Quantity Diagram
Installation Guide - List of Parts
Installation Guide
STEP 2: Installation of bottom tube
Washer
1. Take L-type cross head hex wrench 6# (A) out of the ziplock bag.
2. Remove four hexagon socket button head screws (M8×45) and washers of the front tube ② and
rear tube ③ via the L-type cross head hex wrench 6# (A).
DHex wrench, 4# 1
Before install the seat post,
Loosen the handle by turning
counter-clockwise to make sure
the seat post can be inserted.
STEP 3：Installation of Seat & Seat Post
1.Insert seat post⑯ into the bike frame① in the direction indicated by the arrow, make sure the scale on
the seat post coincides with the top surface of the tube of bike frame, and then tighten by hand turning
the handle to the right.
2.Take seat⑮ out of the ziplock bag.
3.Place the seat⑮ onto the seat post⑯ , and tighten with the provided open-ended wrench (C) in the
direction indicated by the arrow.
⑮
⑯
Installation Guide
3. Align the holes of the front and rear front tube ② and rear tube ③ with the bottom holes of the
frame ①, manually screw the washers and hexagon socket button head screw (M8×45), and tighten
then via the L-type cross head hex wrench 6# (A)
Loose
Tight
Installation Guide
STEP 4: Installation of head tube
1. Pull out the adjusting handle with one hand, while holding the head tube ⑦ and align it with the
mounting hole of the frame with the other hand.
First, loosen the handle
until the head tube ⑦ can
be inserted.
2. Insert the head tube ⑦ into the frame ①, and keep the scale parallel to the top surface of the tube.
Clamp the head tube into the slot. Then tighten the handle to the right.
Loose
Tight
⑩
⑤
⑬
⑫
B
A
Installation Guide
STEP 5: Installation of handlebar assembly
1. Take one Hexagon socket button head screw(M8×12) ⑬, three hexagon socket button head screw
(M6×30) ⑫ and washers ⑨ out of the ziplock bag.
2. Align the hole at the connection of the head tube ⑦ with the handlebar assembly ⑤, and manually
rotate the hexagon socket button head screw ⑬ into the red hole (without tightening). Insert the
mobile phone holder ⑧ into the round hole of the hand as indicated by the arrow. Align the holes
correctly, and manually rotate three Hexagon socket button head screw M6×30 ⑫ and washers into
holes.
4. Lock the hexagon socket button head screw (M8×12) ⑬with the L-type cross head hex wrench 5#
(A). Then tighten the three hexagon socket button head screw (M6×30) ⑫ with the hex wrench 5#.
5. Fasten the decorative cover ⑩ onto the handlebar assembly ⑤.
⑬
⑫
⑧
⑨
⑦
⑤
⑥
STEP 6: Installation of tablet (mobile phone) holder
1. Take the hex wrench 4#(D) out of the ziplock bag.
2. Remove the screws(M6×10) pre-installed on the tablet holder with the provided hex wrench 4#(D)
Hex wrench 4#(D)
Note: Tighten the screws (M6×10) with the
hex wrench 4# (D); otherwise, the bike may
shake during riding.
3. Insert the tablet (mobile phone) holder ⑥ into the slot of the handlebar assembly ⑤, manually
fasten the screws (M6×10) into holes, and lock them via the hex wrench 4# (D).
Installation Guide
This manual suits for next models
1
Table of contents
Languages:
Other YESOUL Exercise Bike manuals
