Yawarra ALIX 3 User manual
ALIX 3
Quick Start Guide
Thank you for purchasing an ALIX 3 computer.
Your package should contain:
ALIX 3 board
Optional Extras
Case
Compact lash card
miniPCI card(s)
Pigtail(s)
Antenna(s)
Power supply
Please read the following instructions to begin using your ALIX 3.
© Yawarra Tiny Computers April 2014
ALIX 3 – Quick Start Guide 2
Things you will need
Tools
Anti-static wrist strap
Phillips head screwdriver
Compact lash card reader (optional)
Null modem cable (optional)
Materials
If you don't have them already, you'll need:
Compact lash Card
miniPCI cards e.g. wireless adapter
Pigtail(s) and antenna(s)
Power supply
Operating system image for the ALIX 3
Instructions
Safety Note
The ALIX 3 board, like all electronic equipment, is sensitive to damage from static discharge.
To avoid damage caused by static discharge, we strongly recommend that you use an anti-
static wrist strap when handling the board.
Step 1 Remove the case
To install the Compact lash (C ) and/or miniPCI cards into the ALIX 3, you will need to
remove the board from the case.
1. Disconnect power and all cables.
Note: The C socket on this machine is not hot-swappable.
2. Remove the four screws from the end plate on the rear of the case (the end with the
ethernet and serial ports).
3. Holding the board by the serial port, carefully slide the board out from the case.
Note: You do not need to remove the end plate from the board to set up your ALIX 3
box. To remove the end plate from the board, remove the serial port screws.
Step 2 Co figure a d i stall a Compact Flash card
To use your ALIX 3, you will need to have a C card with a suitable operating system
installed in the C socket on the ALIX 3 board.
If your C card does not already have an operating system installed, you can either mount the
C card in another machine (e.g. via a flash card reader or a C to IDE adapter) and copy a
boot image onto it, or network boot the ALIX 3. The ALIX 3 supports many operating
systems including BSD, Linux and a number of proprietary operating systems.
© Yawarra Tiny Computers April 2014
ALIX 3 – Quick Start Guide 3
Installation
Insert the C card into the socket on the underside of the board, label up. Ensure the C
card is fully engaged in the socket.
Removal
To remove the C card from the ALIX 3 board, grasp the C card firmly between thumb and
index finger and pull straight out, taking care not to lift or twist the card as this may damage
the connector pins.
Step 3 I stall the mi iPCI card(s) (optio al)
Insert your miniPCI card into the miniPCI slot at an angle of about 45° to the board. Ensure
that the card is firmly seated in the slot and then lay it onto the board, pressing down until the
locking tabs on either side of the card click into place.
If you are installing a wireless card, please note that like all electronic equipment, they are
sensitive to damage from static discharge, especially the R switch and the power amplifier.
To avoid damage caused by static discharge, we strongly recommend that you do the
following when installing a wireless radio card.
•Touch your hands and the bag containing the wireless card to a ground point on the
board (for example one of the holes in the corner of the board). This will equalize the
potential of the wireless card and board.
•Insert the radio card into the miniPCI slot on the board.
•Install the bulkhead end of the pigtail into the case. This will ground the pigtail to the case.
•Touch the u.fl end of the pigtail to a ground point on the board to discharge any static,
then attach the u.fl end to the connector on the wireless card.
Step 4 I stall the pigtail(s) (optio al)
Remove the rubber blanking plug from the punchout in the end plate and insert the SMA
pigtail. Screw the pigtail retaining washer and nut onto the pigtail to secure it to the case.
Attach the u.fl end of the pigtail to the connector on the wireless card. If your wireless
adapter is on the underside of the board, feed the pigtail cable through the notch on the edge
of the board before attaching it to the card.
Step 5 Rei stall the board i to the case
Before you can begin using your ALIX 3, you will need to reinstall the board into the case.
1. Slide the board, with end plate attached, back into the case, ensuring that the edges of the
board are inserted into the slots in the sides of the case.
2. Insert the end plate screws and tighten.
© Yawarra Tiny Computers April 2014
ALIX 3 – Quick Start Guide 4
EMC Compliance
Please note that in order to comply with ACMA emissions regulations, the ALIX 3 board
must be housed in a suitable metal enclosure.
Step 6 Attach the a te a(s) (optio al)
Screw the antenna onto the pigtail and position as required.
Step 7 Co ect to the serial co sole (optio al)
If you want to configure your operating system via the console, you will need to connect to
the serial port via a null modem cable.
Your terminal emulator should be set to 38400 baud, 8 bits, no parity, 1 stop bit, no flow
control.
Step 8 Apply power
Plug the power supply into the DC jack on the ALIX 3. The ALIX 3 runs on 7-18V DC, and
uses about 5W at 12V (excluding miniPCI cards). You'll need a power supply with a 2.1mm
internal, 5.5mm external, centre positive plug.
The ALIX 3 will go through its boot up cycle, which you can watch if you are connected to
the serial console. The behaviour of the three LEDs on the ALIX 3 board is as follows:
•during memory check all LEDs on
•during O/S start up left-hand LED on
•after boot up operating system dependent
Your ALIX 3 is ready to use!
More i formatio
or more detailed instructions on using your ALIX 3, please visit our website at
www.yawarra.com.au and download the manufacturer's user guide.
Contact us
Please feel free to contact us if you have any queries regarding your ALIX 3.
Yawarra Tiny Com uters
Website www.yawarra.com.au
Email [email protected]
Phone 1300 859 799
Mail PO Box 606, Boronia VIC 3155, Australia
© Yawarra Tiny Computers April 2014
Table of contents
Other Yawarra Desktop manuals
