Whirlpool W10679043A User manual

W10679043A

W10755903A - SP

Table of Contents

DRYER SAFETY......................................................................... 2

INSTALLATION REQUIREMENTS........................................... 2

Tools and Parts...................................................................... 2

LOCATION REQUIREMENTS................................................... 3

DRAIN SYSTEM ......................................................................... 5

ELECTRICAL REQUIREMENTS - U.S.A. ONLY ..................... 5

ELECTRIC DRYER POWER HOOKUP - CANADA ONLY...... 6

INSTALL LEVELING LEGS ....................................................... 7

ELECTRICAL INSTALLATION - U.S.A. ONLY ........................ 8

Power Supply Cord Connection ........................................... 8

Direct Wire Connection....................................................... 11

CONNECT OUTLET HOSE ..................................................... 14

LEVEL DRYER ......................................................................... 14

COMPLETE INSTALLATION CHECKLIST ............................ 15

DOOR REVERSAL (OPTIONAL)............................................. 16

TROUBLESHOOTING ............................................................. 22

HybridCare™ Heat

Pump Dryer

Installation Instructions

Para una version de estas instrucciones en español, visite www.Whirlpool.com or www.maytag.com

Sécheuse à pompe à

chaleur HybridCare™

Instructions d’installation

Table des matières

SÉCURITÉ DE LA SÉCHEUSE ............................................... 23

EXIGENCES D’INSTALLATION.............................................. 23

Outillage et pièces ............................................................... 23

EXIGENCES D’EMPLACEMENT............................................ 24

SYSTÈME DE VIDANGE .......................................................... 26

SÉCHEUSE ÉLECTRIQUE RACCORDEMENT

À L’ALIMENTATION ÉLECTRIQUE -

CANADA SEULEMENT ........................................................... 26

INSTALLATION DES PIEDS DE NIVELLEMENT .................. 27

CONNEXION DU TUYAU DE SORTIE ................................... 27

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE...................... 28

ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION...... 29

INVERSION DE LA PORTE (FACULTATIF) ........................... 30

DÉPANNAGE .................................... COUVERTURE ARRIÈRE

INSTALLATION NOTES

Date of purchase:_________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

Date d’achat :_____________________________________

Date d’installation : ________________________________

Installateur : ______________________________________

Numéro de modèle :________________________________

Numéro de série :__________________________________

NOTES CONCERNANT L’INSTALLATION

Installation Requirements

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed:

Flat-blade screwdriver #2 Phillips screwdriver Wire stripper (direct wire

installations)

Dryer Safety

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

Channel locks

Certain internal parts are intentionally not grounded and may present a risk of electric shock

only during servicing.

Service Personnel – Do not contact the thermostat bracket while the appliance is energized.

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

1/4" and 5/16" nut driver

(recommended)

Utility knife Tape measure

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts

are included.

NOTE: Do not use leveling legs supplied with dryer if installing

with a pedestal or a stack kit.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be

at least 4 ft. (1.22 m) long. The wires that connect to

the dryer must end in ring terminals or spade terminals

with upturned ends.

■A UL listed strain relief.

Additional Accessories: (Not supplied with dryer)

Refer to your Use and Care Guide for information about

accessories available for your dryer.

Parts supplied:

6' (1829 mm) drain

hose with couplers

Cable ties (2)

Location Requirements

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

You will need:

■A separate 30 amp circuit.

■If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer. See

“Electrical Requirements.”

■Floor must support dryer weight of 200 lbs. (90.7 kg). Also

consider weight of companion appliance.

■Level oor with maximum slope of 1" (25 mm) under entire

dryer. If forward slope is greater than 1" (25 mm), water could

run out from front of lter. Install Extended Dryer Feet Kit, Part

Number 279810. If not level, clothes may not tumble properly

and automatic sensor cycles may not operate correctly.

■For garage installation, place dryer at least 18" (460 mm)

above oor. If using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

■The dryer must not be installed or stored in an area where it

will be exposed to water and/or weather.

IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

40° F (4° C). Lower temperatures may cause dryer not to

shut off at end of automatic sensor cycles, resulting in longer

drying times.

DRYER DIMENSIONS

27"

(686 mm)

383/4" Min.

(984 mm)

39" Max.

(990 mm)

Front view:

Level Pliers

Installation spacing for recessed area

or closet installation

All dimensions show recommended and minimum spacing allowed.

■Additional spacing should be considered for ease of

installation and servicing.

■Additional clearances might be required for wall, door, oor,

moldings, and drain system.

■Additional spacing should be considered on all sides of the dryer

to reduce noise transfer.

■For closet installation, with a door, minimum ventilation openings

in the top and bottom of the door are required. Louvered doors

with equivalent ventilation openings are acceptable.

■Companion appliance spacing should also be considered.

Recommended installation clearances (dryer only):

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile

home construction and Safety, Title 24, HUD Part 280)

or Standard CAN/CSA-Z240 MH.

18" min.

(457 mm)

(25 mm)

(127 mm)

24 in.2 min.

(155 cm2)

48 in.2 min.

(310 cm2)

(76 mm)

(25 mm)

Side view:

Back view:

131/2"

(343 mm) 61/2"

(165 mm)

61/2"

(165 mm)

297/8"*

(759 mm)

NOTE: Allow

clearance behind

dryer for proper

drain hose routing

and cooling fan

ventilation. Push

dryer back as

far as possible

and make sure

drain hose is not

crushed or kinked.

* Approx. measurement.

Water

drain Cooling

fan

IMPORTANT: Do not block cooling fan as your dryer may not

operate properly.

Power cord/

cable

NOTE: 0" ( 0 mm)

spacing is allowed

behind dryer, providing

drain hose is not kinked

or pinched.

Drain System

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)

diameter to 1" (25 mm) diameter Standpipe Adapter Kit is

available. Top of standpipe must be at least 30" (762 mm) high;

install no higher than 54" (1.37 m) from bottom of dryer.

IMPORTANT: Only 4.5" (114 mm) of drain hose should be inside

standpipe; do not force excess hose into standpipe.

Wall standpipe drain system

4.5"

(114 mm)

Floor standpipe drain system

See requirements for oor standpipe drain system.

Drain system can be installed using a oor drain, wall standpipe,

oor standpipe, or laundry tub. Select method you need.

IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain

hose should be inside standpipe. Always secure drain hose with

cable tie.

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be

at least 30" (762 mm) above oor; install no higher than

54" (1.37 m) from bottom of dryer.

IMPORTANT: Only 4.5" (114 mm) of drain hose should lay

on side of laundry tub. Do not lay the hose at the bottom of tub.

Electrical Requirements -

U.S.A. Only

It is your responsibility:

■To contact a qualied electrical installer.

■To be sure that the electrical connection is adequate and

in conformance with the National Electrical Code, ANSI/

NFPA 70 – latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■To supply the required 3 or 4 wire, single phase, 120/240

volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208

volt electrical supply, if specied on the serial/rating plate)

on a separate 30-amp circuit, fused on both sides of the line.

Connect to an individual branch circuit. Do not have a fuse in

the neutral or grounding circuit.

■Do not use an extension cord.

■If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

Remove the U-bend at the end of the drain hose by cutting

the hose at the end of the U-bend for the oor drain system as

shown in the picture above.

NOTE: Cut hose so that no more than 4.5" (114 mm) of the hose

is in the oor drain to avoid siphoning.

Floor drain system

4.5"

(114 mm)

4.5"

(114 mm)

max. 54"

(1372 mm)

min. 30"

(762 mm)

4.5"

(114 mm)

4.5"

(114 mm)

max. 69"

(1753 mm)

min. 30"

(762 mm)

4.5"

(114 mm)

4.5"

(114 mm)

max. 54"

(1372 mm)

min. 30"

(762 mm)

With 15" matching pedestal

Without pedestal

Electric Dryer Power Hookup –

Canada Only

Electrical Requirements

It is your responsibility:

■To contact a qualied electrical installer.

■To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1-latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association, 178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with exible metallic conduit. All

current-carrying wires must be insulated.

■10-gauge solid copper wire (do not use aluminum) at least

5 ft. (1.52 m) long.

Then choose a 4-wire power supply cord with

ring or spade terminals and UL listed strain

relief. The 4-wire power supply cord, at least

4 ft. (1.22 m) long, must have four 10-gauge

copper wires and match a 4-wire receptacle of

NEMA Type 14-30R. The ground wire (ground

conductor) may be either green or bare. The

neutral conductor must be identied by a white

cover.

Then choose a 3-wire power supply cord with

ring or spade terminals and UL listed strain

relief. The 3-wire power supply cord, at least

4 ft. (1.22 m) long, must have three 10-gauge

copper wires and match a 3-wire receptacle

of NEMA Type 10-30R.

4-wire receptacle

(14-30R)

3-wire receptacle

(10-30R)

If your outlet looks like this:

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor

is permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor. The green ground wire of the 4-wire power cord

must be secured to the dryer cabinet with the green

ground screw.

■If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire

connection” section.

■A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations after

1996, (2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be

at least 4 ft. (1.22 m) long. The wires that connect to

the dryer must end in ring terminals or spade terminals

with upturned ends.

■A UL listed strain relief.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■ For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

■To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

■This dryer is equipped with a CSA International Certied

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft. (1.52 m) in length. Be sure

wall receptacle is within reach of dryer’s nal location.

4-wire receptacle (14-30R)

■Do not use an extension cord.

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

8579325. For further information, please reference the

“Assistance or Service” section of the “Use and Care Guide.”

2. Screw in leveling legs

Install Leveling Legs

To avoid damaging oor, use a large at piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

NOTE: Residual water from factory testing may drain when

dryer is laying on it’s side.

1. Prepare dryer for leveling legs

Using a wrench and tape measure, screw leveling legs into

leg holes until bottom of foot is approximately 1/2" (13 mm)

from bottom of dryer.

Now stand the dryer on its feet. Slide the dryer until it is

close to its nal location.

Electric Installation - U.S.A. Only

Remove hold-down screw and terminal block cover.

1. Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA Type 14-30R).

Go to “Power Supply Cord Connection.”

3-wire direct connection:

Go to “Direct Wire Connection.”

4-wire direct connection:

Go to “Direct Wire Connection.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R).

Go to “Power Supply Cord Connection.”

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional

3-wire connection.” This connection may be used with

either a power supply cord or a direct wire connection.

2. Remove terminal block cover

Before you start: disconnect power.

Power supply cord strain relief:

Power Supply Cord Connection

1. Attach power supply cord strain relief

Remove the screws from a 3/4" (19 mm) UL listed strain relief

(UL marking on strain relief). Put the tabs of the two clamp

sections (C) into the hole below the terminal block opening

(B) so that one tab is pointing up (A) and the other is pointing

down (D), and hold in place. Tighten strain relief screws just

enough to hold the two clamp sections (C) together.

4-Wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

4-wire receptacle (NEMA

type 14-30R) 4-prong plug

Spade terminals with

upturned ends Ring terminals

1. Prepare to connect neutral ground

wire and neutral wire

2. Attach power supply cord

to strain relief

2. Connect neutral ground wire and

neutral wire

Put power supply cord through the strain relief. Be sure that

the wire insulation on the power supply cord is inside the

strain relief. The strain relief should have a tight t with the

dryer cabinet and be in a horizontal position. Do not further

tighten strain relief screws at this point.

Remove center terminal block screw (B). Remove neutral

ground wire (E) from green external ground conductor screw (A).

Connect neutral ground wire (E) and neutral wire (white or

center) (C) of power supply cord under center terminal block

screw (B). Tighten screw.

Power supply cord 4-wire receptacle

(NEMA Type 14-30R):

Go to “4-Wire Power Supply Cord

Connection”.

Power supply cord 3-wire receptacle

(NEMA Type 10-30R):

Go to “3-Wire Power Supply Cord

Connection”.

If your outlet looks like this:

3. Connect ground wire

Connect ground wire (F) (green or bare) of power supply cord

under green external ground conductor screw (A). Tighten

screw.

3-wire receptacle (NEMA

type 10-30R) 3-prong plug

Spade terminals with

upturned ends Ring terminals

3. Connect remaining wires

2. Connect neutral wire

4. Connect remaining wires

1. Remove center screw

Connect remaining wires under outer terminal block screws.

Tighten screws. Finally, reinsert tab of terminal block cover

into slot of dryer rear panel. Secure cover with hold-down

screw. Now, go to “Connect Outlet Hose.”

Connect remaining wires under outer terminal block screws.

Tighten screws. Finally, reinsert tab of terminal block cover

into slot of dryer rear panel. Secure cover with hold-down

screw. Now, go to “Connect Outlet Hose.”

Connect neutral wire (white or center) (C) of power supply cord

under center terminal block screw (B). Tighten screw.

Remove center terminal block screw (B).

3-Wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

This manual suits for next models

Table of contents

Languages:

Other Whirlpool Dryer manuals

Whirlpool

Whirlpool Duet WED9500T Service manual

Whirlpool

Whirlpool Duet WGD9400SB0 User manual

Whirlpool

Whirlpool GLE7900XM User manual

Whirlpool

Whirlpool 3405338 User manual

Whirlpool

Whirlpool LI._7681XM User manual

Whirlpool

Whirlpool WED7300XW User manual

Whirlpool

Whirlpool 3LG5706XP User manual

Whirlpool

Whirlpool Atlantis 3LWED4815FW User manual

Whirlpool

Whirlpool WGD5100SQ0 User manual

Whirlpool

Whirlpool GCGM2991TQ0 User manual

Whirlpool

Whirlpool GEQ9800LG1 User manual

Whirlpool

Whirlpool Cabrio WED6200SW0 User manual

Whirlpool

Whirlpool WED9051YW User manual

Whirlpool

Whirlpool AZB 9780/1 User manual

Whirlpool

Whirlpool LEV6634DQ0 User manual

Whirlpool

Whirlpool 3RAWZ480E User manual

Whirlpool

Whirlpool LE7700XW User manual

Whirlpool

Whirlpool WGD94HEX Parts list manual

Whirlpool

Whirlpool W10224585A User manual

Whirlpool

Whirlpool LEV5634AW1 User manual

Whirlpool

Whirlpool WGD5700V - 7.0 Cu Ft Manual

Whirlpool

Whirlpool Cabrio,- WGD5500X Parts list manual

Whirlpool

Whirlpool LE7680XP User manual

Whirlpool

Whirlpool Duet Steam User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions