Whirlpool CGM2743BQ User manual

Whi I

COMMERCIAL

LAUNDRY

INSTALLATION INSTRUCTIONS

COMMERCIAL DRYER GAS OR ELECTRIC

MODELSCGM2743BQ CGM2793BQ CEM2743BQ CEM2793BQ

INSTRUCTIONS D'INSTALLATION

SECHEUSE A USAGE COMMERCIAL i GAZ OU }_LECTRIQUE

MOD]_LESCGM2743BQ CGM2793BQ CEM2743BQ CEM2793BQ

TABLE OF CONTENTS Page

Dryer Safety ............................................................................. 2

Tools &Parts ........................................................................... 5

Dimensions/Clearances ......................................................... 6

Gas Dryer installation Requirements .................................... 7

Electric Dryer Installation Requirements ........................... 10

Dryer Venting Requirements ............................................... 13

Gas Supply Connection ....................................................... 15

installing Leveling Legs, Coin Slide, and Coin Box ............ 17

Electric Dryer Electrical Connections ................................ 18

Leveling ................................................................................. 22

Complete Installation ........................................................... 23

Reversing Dryer Door Swing ............................................... 24

Changing to a30- or 60-Minute Timing Cam ..................... 25

Maintenance instructions .................................................... 26

if You Need Assistance ........................................................ 26

TABLE DES MATIERES Page

S4curit4 de la s4cheuse ...................................................... 28

Outils et pi_ces ................................................................... 31

Dimensions/Distances de d4gagement ........................... 32

Exigences d'installation pour la s4cheuse hgaz ............. 33

Exigences d'installation pour

la s4cheuse 41ectrique ...................................................... 36

Exigences concernant 1'4vacuation

de la s4cheuse .................................................................... 38

Raccordement hla canalisation de gaz ........................... 40

Installation des pieds de nivellement,

de la glissi_re a monnaie et de la caisse

monnaie ............................................................................ 42

Nivellement .......................................................................... 43

Achever PinstaRation ........................................................... 44

inversion du sens d'ouverture de la porte ........................ 45

Installation d'une came de minutage

de 30 ou 60 minutes ............................................................ 46

instructions d'entretien ....................................................... 47

Si vous avez besoin d'assistance ...................................... 47

W10474269A

W10474270A = SP www.whirlpoolcornrnerciallaundry.corn

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This isthe safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions,

You can be killed or seriously injured if you don't follow

instructions,

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING -"Ri,kofFi, "

- Clothes dryer installation must be performed by a qualified installer,

- Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type} duct. if flexible metal duct is installed, it must be of aspecific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

[] It is recommended that the owner post, in a prominent location, instructions for the customer's use in the event the customer

smells gas. This information should be obtained from your gas supplier.

[] Post the following warning in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 1

DRYER SAFETY

WARNING: For your safety, the information in this manual must be followed to minimize !

the risk of fire or explosion, or to prevent property damage, personal injury, or death. J

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

=Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

eClear the room, building, or area of all occupants.

=Immediately carl your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

=if you cannot reach your gas supplier, call the fire department.

- installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

in the State of Massachusetts, the following installation instructionsapply:

[] installationsand repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

IMPORTANT: When discarding or storing your old clothes dryer, remove the door. I

DRYER SAFETY

IMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic

precautions, including the following:

[] Read all instructions before using the dryer.

[] This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any

other purpose.

[] WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear

the area. Contact the dryer owner immediately.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not dry unwashed items in the dryer.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not open door while dryer is in operation. It will stop.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Do not use this dryer without the lint screen in place.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Installation Instructions or in published user-repair

instructions that you understand and have the skills

to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] The final part of a tumble dryer cycle occurs without

heat (cool-down cycle) to ensure that the articles are left

at a temperature that ensures that the items will not be

damaged.

[] WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and dryer exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVE THESE INSTRUCTIONS

TOOLS &PARTS

Tools Needed:

8" (203 mm)

or 10"' (254 ram)

Pipe Wrench

Torx ®_1"=20Security

Screwdriver or Bit

Level

8" (203 mm) or 10" (254 mm)

Adjustable Wrench

that opens to 1" (25 ram)

Flat=Blade Screwdriver PhiUips Screwdriver

1" (25 ram) Hex-Head

Socket Wrench 5/16" (8 ram) Socket Wrench Pliers (that open to

19/16"[39 mm]}

Utility Knife 1/4" (6 ram) Nut Driver 27"(686 mm)

Wood Block

Caulk Gun and Caulk

(for installing new exhaust vent} Vent Clamps Pipe-Joint Compound

Suitable for Gas Type U

Putty Knife

1" (25 ram}

Open=End Wrenches Ruler or Measuring Tape

Parts Supplied:

Foot Boots (4) Leveling Legs(4) Security Cone

(on some models}

5/16"" Hex Head =

18 x 21/2"' Security Bolt

(on some models}

3=Pin 60=Minute Timing Cam

(on some models} 6=Pin 30=Minute Timing Cam

(on some models}

10 TORX is a registered trademark of Saturn Fasteners, Inc. 5

DIMENSIONS/CLEARANCES

Dimensions

Side View Back View

291/4"

(743 mm)

(648 mm}

ram)

1 "

(25 ram)

I I

101/4''

(260 ram)

Bottom Exhaust

81/4''

(210 mm)

31/4=`

(83 mm)

11/2nn

(38 mm)

51/2''

(140 ram)

_.... (686 ram)

ii E,oc,.a

(343ram) /

(279 ram)

I"_- 4" dia

| (102 ram)

* 13"| -*

(330 ram) _ 31/4"

(83 ram)

37"

(940 ram)

(gas iodels',

411/4"

ram)

7ul

(178 ram)

o 6

LI J

_, 141/a''

(359 ram)

Clearances

Recessed Front View

15"

(381 ram) F

0 II

•.,-- (0 mm) I Ul

(25 ram)--,-

Closet Side View

14"

--- (356 mm)

GAS DRYER INSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in agarage.

Failure to do so can result in death, explosion, or fire.

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it

will be exposed to the weather. Proper installation is your

responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements."

[] A level floor with a maximum slope of 1" (25 mm) under

entire dryer, installing the dryer on soft floor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Gas dryer installation clearances

[] The location must be large enough to allow the dryer door to

be fully opened.

[] Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

[] Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets, or

sleeping quarters. Contact your local building inspector.

[] Make sure that lower edges of the cabinet, plus the back

and bottom sides of the dryer, are free of obstructions to

permit adequate clearance of air openings for combustion

air. See "Recessed Area and Closet installation instructions"

below for minimum spacing requirements.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances."

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes and

ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors with

equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

48 in?

(310 cm2)

Front

View

24 in.2

(155 cm2)

Closet

Door

(76 ml

GAS DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

Electrical Shock Hazard

Plug into agrounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

iMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA

70, latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

[] Do not ground to a gas pipe.

[] Do not have a fuse in the neutral or ground circuit.

[] A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

[] This dryer is equipped with a power supply cord having a

3-prong grounding plug.

[] To minimize the possibility of shock, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

[] Check with a qualified electrician if you are not sure the

dryer is properly grounded.

Gas Dryer Grounding

GROUNDING iNSTRUCTiONS

=1For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE iNSTRUCTiONS

GAS DRYER INSTALLATION REQUIREMENTS

Gas Supply

Explosion Hazard

Use anew CSA International approved gas supply line.

Install a shut=off valve,

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Battewmarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dwer has been certified by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level

at the B.T.U. rating indicated on the model/serial plate. Burner

input adjustments are not required when the dwer is operated

up to this elevation.

When installed above 10,000 feet (3048 m), a four percent

(4%) reduction of the burner B.T.U. rating shown on the model/

serial plate is required for each 1,000 foot (305 m) increase in

elevation. For assistance when converting to other gas types

and/or installing above 10,000 feet (3048 m) elevation, contact

your local service company.

ELECTRIC DRYER INSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in a garage.

FaUure to do so can result in death, e×plosion, or fire.

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

iMPORTANT: Do not install or store the dryer where it

will be exposed to the weather. Proper installation is your

responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements."

[] A level floor with a maximum slope of 1" (25 mm) under

entire dryer. Installing the dryer on soft floor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Electric dryer installation clearances

[] The location must be large enough to allow the dryer door

to be fully opened.

[] Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180 °.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

Recessed Area and Closet installation instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances."

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes and

ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

48 in.2

(310 cm2}

Front

View

24 in.2

(155 cm2)

Closet

Door

(76mr

3ml

(76into)

Electrical Requirements = U.S.A. only

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSVNFPA

70-latest edition and all local codes and ordinances.

[] The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

[] A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269.

[] To supply the required 3 or 4 wire, single phase, 120/240

volt, 60 Hz., AC only electrical supply (or 3 or 4 wire,

120/208 volt electrical supply, if specified on the serial/

rating plate) on a separate 30-amp circuit, fused on both

sides of the line. A time delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit.

Do not have a fuse in the neutral or grounding circuit.

[] Do not use an extension cord.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

This manual suits for next models

Table of contents

Languages:

Other Whirlpool Dryer manuals

Whirlpool

Whirlpool CABRIO W10150626 User manual

Whirlpool

Whirlpool LE7665XP User manual

Whirlpool

Whirlpool 3XLEC8647 User manual

Whirlpool

Whirlpool duet GEW9250PL0 User manual

Whirlpool

Whirlpool WED5200TQ0 User manual

Whirlpool

Whirlpool LER5636JQ0 Troubleshooting guide

Whirlpool

Whirlpool GCEM2990TQ User manual

Whirlpool

Whirlpool WED7300DW User manual

Whirlpool

Whirlpool Gold GEX9868JQ1 User manual

Whirlpool

Whirlpool WED5510VQ User manual

Whirlpool

Whirlpool 8TWED5620HW User manual

Whirlpool

Whirlpool cabrio WED6200S Manual

Whirlpool

Whirlpool CEM2760TQ User manual

Whirlpool

Whirlpool FFT CM11 8B GCC User manual

Whirlpool

Whirlpool W10151595A User manual

Whirlpool

Whirlpool Duet Sport YWED8300SB2 User manual

Whirlpool

Whirlpool 4GWED4750 User manual

Whirlpool

Whirlpool Gold LEQ8621PW2 User manual

Whirlpool

Whirlpool Cabrio W10164752A User manual

Whirlpool

Whirlpool Duet Sport WGD8410SW1 User manual

Whirlpool

Whirlpool Gas LG5791XM User manual

Whirlpool

Whirlpool LEV6646AW2 User manual

Whirlpool

Whirlpool AWZ 7913 WP User manual

Whirlpool

Whirlpool LET5624BW1 User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions