Whirlpool AMD 061 User manual

INSTRUCTIONS FOR USE

PORTABLE AIR CONDITIONER WITH GREEN

GAS

PREPARATION BEFORE USE

SAFETY PRECAUTIONS

INTRODUCTION

IDENTIFICATION OF PARTS

REMOTE CONTROL

OPERATION INSTRUCTIONS

MAINTENANCE

TROUBLESHOOTING

PROTECTION

INSTALLATION INSTRUCTIONS

ELECTRICAL CONNECTION

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that

this appliance may not be treated as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste

disposal.

For more detailed information about treatment, recovery and recycling of this product, please

contact your local city office, your household waste disposal service or the shop where you

purchased the product.

PREPARATION BEFORE USE

SAFETY PRECAUTIONS

Before using the air conditioner, be sure to check and preset the following.

• Remote Control presetting

The remote control is NOT preset as Cooling Only Air Conditioner or Cooling Air Conditoner with Electric Heater

by manufacturer.

Each time the remote control batteries are replaced, the Cooling indicator and Heating indicator will flash

alternately on the remote control LCD.

The user can preset the remote control depending on the type of air conditioner purchased:

when flashes, press any button to set Cooling Air Conditioner with Electric Heater;

when flashes, press any button to set Cooling Only.

If you don’t press any button within 12 seconds, the remote control will be automatically preset as Cooling Air

Conditoner with Electric Heater (6th Sense mode).

Be sure not to do the following.

•Do not direct the cool air at yourself for long period of time, this may harm

your health. Deflect the air flow around the entire room.

•Do not direct the air flow towards gas burners and stoves.

•Do not touch the operation buttons when your hands are wet.

Pay attention to such a situation.

•Do not repair the appliance by yourself. Mistakes may result in electric

shock etc..

Be sure to follow this instruction.

•Do not put any objects on the outdoor unit.

Earthing is essential.

•It is the user’s responsibility to have the appliance earthed according to

local laws by a qualified technician.

Warning: Incorrect handling could cause a serious hazard, such as

death, serious injury, etc.

•Connect to the correct power supply as specified on the rating plate and

do not use extension cables which could generate a serious fault or

hazard, or cause a fire to break out.

•Keep the power supply circuit breaker or plug clean. Make sure the power

cable is plugged in securely and correctly as insufficient contact could

cause electric shock or fire.

•Do not try to disconnect the circuit breaker or pull the plug out to turn

the appliance off. This may cause a fire due to sparks, etc.

•Do not twist, pull or press the power cable as this may damage the cable

and result in electric shock or fire.

•Do not insert sticks or similar objects into the appliance as this could cause

injury when the fan rotates at high speed.

•In the event of a fault, switch the appliance off using the remote control

before disconnecting it from the power supply.

INTRODUCTION

Thank you for choosing this portable air conditioner. It will provide you and your family with all the Home Comfort

requirements you may need for your home, cottage or office. The appliance can easily be moved from room to room and

set up in just a few minutes.

It is a multi-functional room air exchanging, air-processing appliance, designed to offer you the functions of:

Air Conditioning, Dehumidifying, Heating and Independent Fan.

This manual will provide you with valuable information necessary for the proper care and maintenance of your new

appliance. Please take a few moments and read the instructions thoroughly. If properly maintained, your appliance will

give you many years of trouble free operation.

Electrical Specifications

1. All wiring must comply with local and national electrical standards and be installed by a qualified electrician. If you

have any questions regarding the following instructions, contact a qualified electrician.

2. Check the available power supply and rectify any wiring problems before installation and operation of this unit.

3. For your safety and protection, this appliance is earthed through the plug on the power cable when plugged into a

matching socket. If you are not sure if the sockets in your home are properly earthed, consult an electrician. Do not

use the appliance with adapters or extension cables.

If an extension cable is required, use only heavy appliance extension cables (available in most local hardware shops).

IDENTIFICATION OF PARTS

Front

1- Control panel

2- Air outlet

3- Signal receiver

4- Remote control

5- Transport handle

Back

6- Air outlet hose

7- Evaporator air intake

8- Rubber plug

9- Drain Hose

J- Power supply cord

NOTE:

The above drawing is a simplified representation of the air conditioner, which may differ slightly from the

actual appliance you have purchased.

Front

Back

A-ON/OFF button: to start or stop the appliance

B-MODE button: to select the operation mode

C-FAN button: to select the fan speed

D-TIMER ON button: to set or cancel the Timer On function

E-TIMER OFF button: to set or cancel the Timer Off function

F-TEMP./TIMER setting buttons: to select temperature, adjust real time or set time

G-RUN indicator (green): lit up when the appliance is running

H-WATER FULL indicator (red): lights up when water needs to be drained

I-

HEATER button: to heat the room

J-

LCD display: identical to the LCD display on the remote control with the exception of the

temperature display.

Room temperature display

Flashes when temperature is being set

Used to regulate temperature

in 6th sense mode or DRY mode

Control Panel

REMOTE CONTROL

NOTE: Each mode and relevant function is described in the following pages.

The remote control transmits signals to the system.

A. ON/OFF button

Press this button to start the appliance when it is connected to the

power supply or to stop it when the appliance is running.

B. MODE button

Used to select the operation mode.

C. SWING button

Used to adjust the direction of air flow.

D. 6th Sense button

To enable fuzzy logic function when the unit is either on or off.

E. button

To display temperature in either °C or °F

F. LOCK BUTTON

To enable or disable buttons on remote control.

G. CLOCK BUTTON

To view or set time.

H. TIMER OFF button

To set or cancel Timer Off function.

I. TIMER ON button

To set or cancel Timer On function.

J. ROOM TEMPERATURE SETTING buttons

To s e l e c t r o o m t e m p e r a t u r e .

To adjust real time or set time.

K. JET button

To start or stop fast cooling.

L. FAN button

To select auto, high or low fan speed.

Indication symbols on LCD:

Signal transmit

6th Sense indicator

Cooling indicator

Dry indicator

Fan only indicator

Lock indicator

Heating indicator

Jet control indicator

Fan speed indicator

Display set temperature

Timer On or Timer Off

indicator

Display real time

How to insert the batteries

•Remove the battery cover in the direction of the arrow.

•Insert new batteries making sure that the (+) and (-) of battery are

matched correctly.

•Refit the cover by sliding it back into position.

NOTE:

•Use 2 AA (1.5 V) batteries. Do not use rechargeable batteries. Replace

batteries with new ones of the same type when the display becomes dim.

TO BE DONE BY THE USER - If the batteries are replaced within 1

minute, all remote control settings will be preserved. To reset the remote

control, wait 3 minutes before inserting new batteries (see page 20 for

details).

Storage and tips for using the remote control

The remote control can be stored in a wall-mounted holder.

NOTE: The remote control holder is an optional accessory.

How to use the remote control

To operate the room air conditioner, point the remote control at the signal

receiver. The remote control will operate the air conditioner at a distance of

up to 7 m when pointing at the signal receiver of the indoor unit.

Remote control holder

Signal

receiver

OPERATION INSTRUCTIONS

Cooling mode

Dry mode

Operating modes

1. Selecting mode

Each time the MODE button is pressed, operating mode changes in the

following sequence:

COOLING DRY FAN ONLY HEATER

2. “FAN” mode

Each time the “FAN” button is pressed, the fan speed changes in the

following sequence:

AUTO HIGH LOW

IMPORTANT:

•In “FAN ONLY” mode, only “High” and “Low” are available.

•In “DRY” mode, airflow is set at “Low” automatically, “FAN” button

is ineffective in this case.

3. Setting temperature

Press once to raise temperature setting by 1°C

Press once to lower temperature setting by 1°C

Temperature range for presetting:

COOLING 18°C ~ 32°C

DRY room temperature ± 2°C

FAN ONLY unable to set

4. Turning on

Press the button. The RUN indicator will light up on the indoor unit

when the signal is received.

Jet, 6th sense, DRY, TIMER ON and TIMER OFF operating modes

will be specified in the following pages.

IMPORTANT:

• The unit will often not respond immediately when operating mode

is changed during operation. Wait for 3 minutes.

• Allow 3 minutes to elapse before restarting the appliance.

If you want to cool the room, you can operate the appliance as follows:

1. Press the MODE button and select cooling mode.

2. Press the FAN button to select the fan speed.

3. You also can set the appropriate temperature by using the temperature button.

4. When the above steps have been completed, press the ON/OFF button to make the appliance run in cooling

mode.

5. You can adjust the fan direction by pressing the SWING button; press once to start, again to stop.

This function dehumidifies the room.

1. Press the MODE button and select dry mode.

2. You can set the appropriate temperature by using the temperature button.

3. Press the ON/OFF button to make the appliance run in dry mode.

4. You can adjust the fan direction by pressing the SWING button; press

once to start, again to stop.

Note:

• The dry mode cannot be used to cool the room.

• A hot air outlet hose is required in Dry mode.

• In dry mode, fan speed is preset by the appliance, so the fan button

is not applicable.

• In heater mode, and are not applicable.

Heater mode

Additional instructions

6th Sense mode

1. Press the MODE button and select heater mode.

2. You can set TIMER ON or TIMER OFF in heating mode.

1. If you select cooling or dry mode while the appliance is in another mode, the compressor will be delay-protected.

Wait for 3~5 minutes, after which the appliance will run again. Do not press any button during the waiting time,

or the appliance will re-count the protection time.

2. In Cool or Dry mode the compressor and fan will stop when the room temperature reaches the set temperature.

Pressing the 6th Sense button enables fuzzy logic function with the unit either on or off. In this mode, temperature and

fan speed are set automatically depending on the actual room temperature.

Pressing the FAN button in 6th Sense mode when the appliance is in cooling mode will change fan speed in the following

sequence: Auto - High - Low. In dry mode, the LCD display will appear as shown in the figure on the right although only

Auto-speed will be enabled.

Operation mode and temperature are determined by indoor temperature

Indoor temperature Operation

mode Target temperature

23°C or below DRY Room temperature decreases 1.5°C after

operating for 3 minutes

Over 23 COOLING 23°C

Important: 6th Sense button is ineffective in JET mode.

Note: Temperature, airflow and direction are controlled automatically in 6th Sense mode. However, a

decrease or increase of up to 2°C can be set with the remote control or control panel if you still feel

uncomfortable.

A decrease or increase of up to 2°C can be set in 6th Sense mode

Your feeling Button Adjustment procedure

Slightly warmer

A decrease up to 2°C can be set

Press once to lower the set temp by 1°C

Press twice to lower the set temp by 2°C

Slightly cooler

A rise up to 2°C can be set

Press once to raise the set temp by 1°C

Press twice to raise the set temp by 2°C

Uncomfortable because of unsuitable air flow

volume. Indoor fan speed switches from High to Low

each time the button is pressed.

Uncomfortable because of unsuitable flow

direction.

Press once to alter the position of the vertical

louver and change the direction of airflow.

Note: There is no swing button on the

control panel. Pressing the FAN button for

3 seconds will enable the swing function on

the control panel. Press the FAN button

again for 3 seconds to cancel this function.

Timer on setting

Setting the timer with the TIMER ON function when leaving the house in the

morning is ideal to find a comfortable room temperature on your return.

When you press TIMER ON, the ON indicator and 12:00 flash on the display.

Press the or , to increase or decrease the set time by 10 minutes. Press

and hold for 1.5 seconds to increase or decrease the set time in continuous

10 minute steps.

Time can be set up to 24 hours in advance. When you have set the "TIMER

ON" time, press TIMER ON again to confirm the TIMER ON setting.

How to cancel timer on

To cancel the timer ON setting, press the TIMER ON button for 3 seconds,

or the setting will be active every day.

Timer off setting

Timer Off function is set using the TIMER OFF button in the same way as

TIMER ON.

Adjusting the real time

You can adjust the real time by pressing the CLOCK button. Use the and

buttons to set the correct time and press the CLOCK button again to

confirm.

Note: Time can be adjusted in any mode using the TIMER ON and TIMER

OFF buttons on the control panel. Press the Timer On and Timer Off button

at the same time, 12:00 will be displayed, and then time can be adjusted.

Press the or button once, the set time will increase or decrease by 1

minute. Press and hold the button for 1.5 seconds to increase or decrease

the set time in continuous 10 minute steps. Time is based on a 24-hour clock

and can be set up to 24 hours in advance. After setting the clock, press

TIMER ON and TIMER OFF together to confirm the time set.

Otherwise, the time will be confirmed automatically after a 5 second delay.

JET mode

•Fast cooling operates at high fan speed, changing the set temperature

automatically to 18°C (64 F).

•Jet mode is used to start or stop fast cooling. Jet mode can be set when

the appliance is in operation or connected to the power supply.

•In Jet mode, you can set airflow direction or the timer. To exit Jet mode,

press either the JET, MODE, FAN, ON/OFF or TEMPERATURE

SETTING buttons and the display with return to the original mode.

Note:

• If none of the aforementioned buttons are pressed, the appliance

with continue to run in Jet mode at a set temperature of 18°C.

• 6th sense button is not available in Jet mode.

Table of contents

Other Whirlpool Air Conditioner manuals

Whirlpool

Whirlpool Cool Impression room air conditioners User manual

Whirlpool

Whirlpool 1188647 Assembly instructions

Whirlpool

Whirlpool ACQ058PP0 User manual

Whirlpool

Whirlpool ACM184XA0 User manual

Whirlpool

Whirlpool COOLERATOR AR0600XV0 User manual

Whirlpool

Whirlpool SWA1040Q User manual

Whirlpool

Whirlpool PORTABLE AIR CONDITIONER User manual

Whirlpool

Whirlpool AWV07000R Installation guide

Whirlpool

Whirlpool ACU109PR Assembly instructions

Whirlpool

Whirlpool ACQL128XS0 User manual

Whirlpool

Whirlpool SIA90IN User manual

Whirlpool

Whirlpool ACP102PS0 User manual

Whirlpool

Whirlpool CA15WYR0 User manual

Whirlpool

Whirlpool AMD 064 User manual

Whirlpool

Whirlpool ACM122XR0 User manual

Whirlpool

Whirlpool AW05CR1SRHUE User manual

Whirlpool

Whirlpool AMD 018 User manual

Whirlpool

Whirlpool ACE184PT1 User manual

Whirlpool

Whirlpool ACQ142XG0 User manual

Whirlpool

Whirlpool AMC 992 User manual

Whirlpool

Whirlpool ASV09000R User manual

Whirlpool

Whirlpool ACC082XR0 User manual

Whirlpool

Whirlpool 819052092 Assembly instructions

Whirlpool

Whirlpool ACPS82 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual