Whirlpool ACSL02XT User manual

YEid 01

Installationlniiitionsand

Use&CareGuide

Control panel

Model and

serial number

plate

(not shown)

Air discharge

Control panel

Model and

serial number

plate

AIRCONDITIONERS

ModelsACS602XT ACS802XV ACSl02XT ACC602XT

a-s3

Contents

Page

Electrical Requirements. ..........

Receptacle wiring .................

Electrical requirements .............

Electrical connection ..............

Installation Instructions ...........

Installation instructions 1 ...........

Installation instructions 2 ...........

Operating Instructions ............

Starting your air conditioner .........

The exhaust control ...............

Changing air direction ..............

Cleaning and caring for your

air conditioner ..................

It You Need Service Or Assistance

Whirlpool Room Air Conditioner

Warranty ..........................

01969 Whirlpool Corporation

Thank you for buying a Whirlpool appliance.

Please complete and mail the Owner

Registration Card provided with this prod-

uct. Then complete the form below. Have this

information ready if you need service or call with

a question.

Copy model and serial numbers from plate

(see diagram on page 12) and purchase date

from sales slip.

Keep this book and sales slip together in a

handy place.

It is your personal responsibility to be sure

your air conditioner:

Has been properly installed.

Is the right size for the area you want to cool.

Is properly connected and grounded to electrical

supply.

Is used only for the job it was intended to do.

Is not used by children or anyone unable to

operate it properly.

Is properly maintained.

Also, remove energy label and buy guide. Use

damp cloth to take off any glue residue. Do not

use a sharp instrument or any harsh or abrasive

cleaners.

Important:

Please read this Use & Care Guide before install-

ing or using your air conditioner. It tells you how to

install and operate it, and gives important electrical

information. Save it for future use in case you have

a question or move the air conditioner.

Personal Injury Hazard

The metal fins on the coils are sharp. Han-

dle the air conditioner with care. Failure to

do so could result in personal injury.

Model Number

Serial Number

Purchase Date

Servlce Company Phone Number

ElectricalRequirements

Electrical requirements are different for the two

models pictured on the cover, depending on the

ampere rating of your unit. The number of

amperes is printed on the serial plate, which is

attached to the front of the unit behind the front

panel (see diagram on page 12).

Observe all local governing codes and

ordinances.

Do not, under any circumstances, remove

the power supply cord grounding prong.

Receptaclewiring

Receptacle wiring should be a minimum of 14

gauge. Use copper wire only. It is the personal

responsibility of the consumer to provide proper

and adequate receptacle wiring installed by a

qualified electrician. Observe National Electrical

Code and all local governing codes and

ordinances.

Z&prong

Electricalrequirements

Electrical Shock Hazard

Check with a qualified electrician if you

are in doubt as to whether the appliance is

properly grounded. Do not modify the

power supply cord plug - if it will not fit

the outlet, have a proper outlet installed

by a qualified electrician. Improper

connection of the equipment-grounding

conductor can result

in a risk of

electrical shock.

Do not use an extension cord with this

appliance. Such use may result in a fire,

electrical shock or other personal injury.

. Do not have a fuse in the neutral or

grounding circuit. This could result in a

risk of electrical shock.

A 115volt, 60 Hz AC only, 15 ampere fused elec-

trical supply is required (time delay fuse or time

delay circuit breaker required). It is recommended

that a separate circuit, serving only this appliance,

be provided for models with serial plate amperes

up through 7.5. A separate circuit is required

for models with serial plate amperes of 7.6

through 12.0.

Electricalconnection

Electrical ground is required on this appliance.

Recommended grounding method

For your personal safety, this appliance must be

grounded. This air conditioner is equipped with a

power supply cord having a 3-prong grounding

plug. To minimize possible shock hazard, the cord

must be plugged into a mating 3-prong grounding

type wall receptacle, grounded in accordance with

the National Electrical Code, ANSVNFPA 70-1987

(or to the latest), and local codes and ordinances.

If a mating wall receptacle is not available, it is the

personal responsibility of the customer to have a

properly grounded 3-prong wall receptacle

installed by a qualified electrician.

Electrical Requirements

Continued

Electrically

grounded metal

cold water pipe

Ground assembly

(attach to grounded

Grounded eyelet

Grounding prong

Temporary grounding method

If changing and properly grounding the wall recep-

tacle is impossible and where local codes permit

(consult your electrical inspector), a temporary

adapter may be plugged into the existing 2-prong

wall receptacle to male with the 3-prong power

supply cord. This, however, is not recommended.

If this is done, however, you must connect the

grounded eyelet on the adapter to the wall recep-

tacle cover plate screw and from this same screw,

you must connect a separate copper ground wire

(#14 minimum) to a grounded cold water pipe.

‘Do not ground to a gas supply pipe. Do not

connect to electrical supply until appliance is

grounded. Do not, under any circumslances,

remove the power supply cord grounding prong.

*Cold water pipe must have metal continuity to

electrical ground and not be interrupted by plas-

tic, rubber or other electrically insulating connec-

tors (including water meter or pump) without

adding a jumper wire at these connections.

InstallationInstructions

If you have one of these models:

ACS602XT

ACS802XV

ACS102XT,

follow “Installation instructlons 1” below.

If you have model ACC602XT, follow “lnstalla-

tion instrucGons 2” on page 8.

Installationinstructions1

To help avoid any installation problems and to help

‘assure trouble-free performance of your new air

conditioner, read these installation instructions, as

well as the operating instructions and electrical

requirements before installing your unit.

Also, inspect thecondition of the window where

the air conditioner will be installed. Be sure it will

support the weight of the unit.

Personal Injury Hazard

Because this air conditioner weighs about

90 to 105 pounds, it is recommended that

you have someone help you install your

new unit and that you both use proper lift-

ing techniques.

This appliance must be installed

according to all applicable codes and

ordinances.

Handle the air conditioner with care.

The metal fins on the front and rear

coils are sharp.

. Do not use the collected water for

drinking purposes. It is not sanitary.

Be sure air conditioner does not fall out

of window during or after installation.

Failure to follow the above precautions

could result in personal injury.

1 n

back I’I _

1. Unpack mounting parts before installing

your air conditioner. Make sure you have all the

necessary parts. A normal installation can be

made with a screwdriver, saw, small level, pocket

knife, tape measure, drill and W:

9/64”

and

%6”

drill bits.

Description of parts

1 Shelf (1)

2 Support bracket (1)

3 Sill bracket (1)

%6”

bolt (2)

4A %” nut (2)

%6”

flat washer (2)

%6”

lockwasher (2)

5 Translucent panel (1)

6 Screw-10x1”(2)

6A screw - 10 x

13/4”

(2)

7 Screw - 8 x 34” (5)

8 Side seal strip (1)

9 Lower track seal (1)

10 Locking bracket (1)

11 Foam seal strip (1)

12 Panel frame (1)

13 Thread cutting screw #% x %” (4)

If using Item 13 for fastening Item 10 or 12 to metal

or plastic, use

‘h4”

dia. or #28 drill.

2. Pick the right window. First, decide what

room(s) you want to cool. Then choose a window

that will allow the air-conditioned air to flow freely

and directly into the room(s) you want cooled.

Remember, it’s difficult to move air around corners.

If the inner sliding window slides to the left, the unit

will be installed on the right. Remove window

screen if there is one. Choose a sliding window

that’s also near an electrical outlet. (Refer to

“Electrical Requirements” on page 3 for type of

receptacle and wiring needed.) Do not use an

extension cord.

The sliding window in which you place your air

conditioner should have an opening of at least

15%” wide and 21%” to 40%” high (see diagram).

For installations up to 62%” high, a special kit (Part

No. 977449) is available. For windows as low as

207/re’:you must install without filler frame and

remove top angle on unit, reinstalling 3 screws into

top of cabinet.

This model may also be installed in steel hinged

casement windows. The steel hinged casement

window

mUSt

have an opening at least 15%” wide

and no more than 16%” wide.

3. Place shelf In wlndow with tabs down

against the track surface.

Installation Instructions

Continued

Room side

-16”-

Flush with

window

Use screws 6 or 6A

Predrill Yr4” holes

if tracks are metal

4. Attach support bracket (Item 2) loosely to

the underside of shelf with either short or long leg

down and with end of bracket either toward or

away from window, depending upon construction

and depth of wall and window sill (see diagram).

Attach sill bracket (Item 3). Each bracket is

attached using one

%6”

bolt, nut and washers

(Items 4,4A, 48 and 4C).

5. With the assembled shelf and brackets still

in the window opening, adjust brackets until shelf

is firmly seated and sloping down to outside. If you

use a level, be sure you have % bubble of slope.

Without a level, place the translucent panel (Item

5) on shelf. The top of long side of the panel will be

%6”

back from the window line (see diagram).

6. If slope back is correct, tighten all nuts

securely. Install lower track seal (Item 9) shown in

diagram. This track seal has two holes which line

up with matching screw holes in shelf.

7. Install shelf 2%” from side of window open-

ing, securing it in place with screws 6 or 6A.

6. Measure height of opening (see diagram).

Subtract

20%6”

from measured height. This will be

the actual height of translucent panel.

9. Measure out the distance determined in

Step 8 and mark it along the 20%” side of translu-

cent panel. Clamp panel between a board and an

appropriate supporting surface close to the mark

and cut with fine tooth saw. Remove burrs.

10. Lift vertically removing panel frame from

unit. Slide translucent panel into groove in frame,

keeping honeycomb side to the face side of frame

(see diagram). Slide frame back into place on unit.

Panel should enter the top angle groove.

11. Peel backing from seal strip (Item 8) and

press it onto side filler frame guides on each side

of unit.

Butt to bottom

of flller frame.

cut off axcess

length below

unlt.

Seal

strip

12. Place unit in wlndow by resting unit on

shelf. Push unit toward window so side angles are

sealing against the side jamb stop (see diagram).

Slide the opened window sash firmly to make cer-

tain the frame and unit sealing strips are sealing.

13. Using Ye”drill, install locking screws

(Item 7). Use two screws in top jamb and in the

side bottom flanges. If you need additional holding

strength, add two more screws at upper sides of

filler frame (marked ‘A”). Also, two screws can be

added at unit sides (marked “B”). However, if yqu

add screws at “B:’ you must use a

%6”

drill bit to

predrill through the plastic sides of air conditioner.

14. Lock the sllding sash at bottom using lock

bracket (Item 10) and screw (Item 7) as shown in

diagram at left. Use a ‘/a” drill bit to drill through

track before inserting screw.

15. Cut seal strip (Item 11)to length. Install it

between space of opened sash and glass of the

closed sash (see diagram).

Installation Instructions

Continued

Add angle Add wood Add angle

or 19 gauge as shown to wood stop

Shelf -

Seal, item 9

Use screws,

item 6 or 6A

Tab on -

shelf

avallable opening side

16. For installation In windows having no

slde flanges or with wood stops.

The flanges (top and two sides) on the air condi-

tioner must mate against companion flanges on

the window, not more than

1/16”

(.2 cm) in thickness.

On the side with the opened sash, the leading

edge of the sash becomes the flange. On the top

and jamb side of most metal windows, the flange

is there.

In windows where there are no flanges or where

there are thick wood flanges or stops, use metal

angles or wood to provide a stop for the unit

flange. Diagrams at left show three suggested

methods.

17. For installation in steel casement

windows.

Follow Steps 2 and 3 on page 5. NOTE: In

Step 3, the shelf labs must butt to the front of the

bottom angle on the casement (see diagram

at leff).

When Step 3 is finished, follow Steps 4

through 10 on page 6, and Steps 11and 12 on

page 7. Then proceed with the final two para-

graphs in this Step 17, which immediately follow.

Open window at least 16O’to allow room for

unit cabinet. If necessary, remove window crank

handle so the window will open wide enough and

not interfere with shelf against the bottom sill

angle. Tie opened window to the wall or frame to

prevent the window from swinging.

Drill V”” holes in the window jamb top to

line up with holes in filler frame (see diagram at

left). Use two thread cutting screws (Item 13) to

secure unit. If you need additional holding

strength, add screws at the bottom of the unit

side channels (see Step 13 diagram).

Installationinstructions2

To help avoid any installation problems and to help

assure trouble-free performance of your new air

conditioner, read these installation instructions, as

well as the operating instructions and electrical

requirements before installing your unit.

Inspect the condition of the window where

the air conditioner will be installed. Be sure it will

support the weight of the unit.

Personal Injury Hazard

Be sure air conditioner does not fall out of,

window during installation. Personal injury

or damage could result.

Installation Instructions

Continued

conditioner

%” Max. -I I-

outslde of

wlndow

Back of air

conditioner

5. Check the knurled knob screws to see that

the top mounting brackets (Item 5) are retracted to

the center of the unit. They must not interfere with

the window frame when the unit is installed.

6. Lift the unit into the window opening and

slide it back until the mounting frame comes into

contact with the window frame.

7. Replace the bottom mounting brackets

(Item 3) by hooking the bracket over the window

frame. Replace the top screws (Item 1) in the

mounting bracket, leaving them loose enough so

there is about

%6”

of play. Tighten the bottom

screws (Item 2). This will pull the unit mounting

flange tigh:ly to the window frame, sealing and

locking the air conditioner in place.

6. Loosen the two knurled knob screws and

slide the top mounting bracket (Item 5) toward the

outside of the unit, engaging the window frame.

Tighten the knurled knob screw in this position.

This will lock the unit in place so it cannot tilt into

the room. The installation is now complete.

9. Optional mounting instructions. If the win-

dow thickness will not allow you to use the four

mounting brackets provided with the unit, remove

brackets and fasten flanges of unit with sheet

metal screws. These screws are not included with

your air conditioner. The window opening for your

installation must not be wider than 15’:

Sheet metal

screw ‘S -

Knurled

I I

knob

Wlndow

opening

frame -

Personal Injury Hazard

Because this air conditioner weighs about

70 to 75 pounds, it is recommended that

you have someone help you tnstall your

new unit and that you both use proper lift-

ing techniques.

This appliance must be installed

according to all applicable codes and

ordinances.

Handle the air conditioner with care.

Watch out for the sharp metal fins on the

front and rear coils.

Do not use the collected water for

drinking purposes. It is not sanitary.

Failure to follow the above precautions

could result in personal injury.

1. Unpack mounting parts before installing

your air conditioner. Be sure you have all the nec-

essary parts (see top two diagrams at left). This air

conditioner will fit most steel casement windows. A

normal installation can be made with a screw-

driver,

%6”

socket driver, tape measure and drill.

Description of parts (top hvo diagrams at left)

1 #lO x W long s.m. screw

2 # 1O-32 x 3/s”long math. screw

3 Bottom mounting bracket

4 Knurled knob screw

5 Top mounting bracket

NOTE: Above parts (not shipped loose) installed

on unit by factory.

2. Pick the right window. First, decide what

room(s) you want to cool. Then choose a window

that will allow the air-conditioned air to flow freely

and directly into the room(s) you want cooled.

Remember, it’s difficult to move air around corners.

Choose a window that’s also near an electrical

outlet. (Refer to “Electrical Bequirements” on

page 3 for type of receptacle and wiring needed.)

Do not use an extension cord.

To be able to use the window mounting parts

shown in the diagram to the left of Step 1above,

the window should have a minimum width of 14%”

and a maximum width of 16” (see “A” in bottom

diagram). The window should have a minimum

height of 10%” and a maximum height of 11%”

(see “B” in bottom diagram).

3. Remove the glass from the frame opening

selected. Clear away any hardened putty.

4. Before sliding unit through the casement

opening, remove the bottom window bracket

(Item 3) on both sides of the unit. NOTE: Only the

top screws (Item 1) need to be removed. 9

This manual suits for next models

Table of contents

Other Whirlpool Air Conditioner manuals

Whirlpool

Whirlpool WA9260Q User manual

Whirlpool

Whirlpool AR1000 User manual

Whirlpool

Whirlpool ACU088PR0 User manual

Whirlpool

Whirlpool ACM082PS7 User manual

Whirlpool

Whirlpool AMAP101AB User manual

Whirlpool

Whirlpool 1188908 Assembly instructions

Whirlpool

Whirlpool ACU124PK0 Product information sheet

Whirlpool

Whirlpool ACE082XH0 User manual

Whirlpool

Whirlpool X05002X0 User manual

Whirlpool

Whirlpool ASV09000R User manual

Whirlpool

Whirlpool AMAP050BW User manual

Whirlpool

Whirlpool ROOM AIR CONDITIONER User manual

Whirlpool

Whirlpool YACQ088XP0 User manual

Whirlpool

Whirlpool AMD 061 User manual

Whirlpool

Whirlpool 63851341 Assembly instructions

Whirlpool

Whirlpool PORTABLE AIR CONDITIONER User manual

Whirlpool

Whirlpool AMD 091/1 User manual

Whirlpool

Whirlpool CA25WC50 Operation manual

Whirlpool

Whirlpool ACC082XR0 User manual

Whirlpool

Whirlpool ROOM AIR CONDITIONER User manual

Whirlpool

Whirlpool WAHMS User manual

Whirlpool

Whirlpool BHAC1400XS0 User manual

Whirlpool

Whirlpool 1163570 User manual

Whirlpool

Whirlpool WA6059Q User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual