Wenger Essential Lab Workstation User manual
Assembly Instructions
Essential Lab Workstation
©Wenger Corporation 2015 Printed in USA 03/15 Part #256A113-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: +1(507) 455-4100 • www.wengercorp.com
Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Hardware Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Note: Please read and understand these instructions before starting the assembly.
Note: Examine the illustrations on the following pages. If you need additional information,
contact Wenger Corporation using the information below.
Visit the Music Lab Workstations web page at www.wengercorp.com.
2
Important User Information
General
Copyright©2015 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted
in any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser’s personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that
might occur. The end user must exercise caution and common sense when assembling or installing
Wenger Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-
887-7145.
Manufacturer
The Essential Lab Workstation is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • +1 (507) 455-4100
www.wengercorp.com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
· This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ten full years from
date of shipment. A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the
individual manufacturer’s warranty.
3
Required Tools
· Phillips Head Screwdriver
· 3/8” & 7/16” Open-End Wrenches, or Sockets
· 3/16” Allen Wrench (supplied)
· 5/32” Allen Wrench (supplied)
Hardware Parts List
*Quantities may vary, extras can be discarded.
X003497
#10 x 1.75
Pan Head Screw
1
X001503
#10-16 x 3/4
Pan Head Screw
2
X003283
1/4-20 x .590
Machine Screw
3
X003311
1/4-20
Cap Nut
4
X003067
1/4-20 x 5/8
Truss Head Screw
5
X002971
1/4-20 x 1/2
Carriage Bolt
6
X003458
1/4-20
Lock Nut
7
X001843
#10-32 x 3/8
Pan Head Screw
8
X003499
10-32
Jam Lock Nut
9
X003583
2-3/8” Grommet
10
256A125
Headphone Mount
11
X003600
Wiring Clamp
12
X001948
3/16” Allen Wrench
14
X001811
5/32” Allen Wrench
15
256A012
Spacer Tube
(Optional)
14
4
Assembly
1. Lay the Desktop at on the ground with the pilot holes facing up.
Be careful not to scratch the Desktop surface!
2. Attach the Legs to the bottom of the Desktop in the orientation shown below.
a. If including the Optional Spacer Tubes (#13), attach the Legs and Spacer Tubes
to the Desktop pilot holes using six #10-16 x 1.75 Pan Head Screws (#1).
b. If not attaching the Optional SpacerTubes, attach the Legs to the Desktop pilot holes
using six #10-16 x 3/4 Pan Head Screws (#2).
The use of Spacer Tubes must be the same on both Legs.
If not using Optional
Spacer Tubes
Back of
Leg
If using Optional
Spacer Tubes
Example only. If optional spacer tubes are used, they must be attached to both legs.
Spacer
Tube
(#13)
#10 x 1.75
Pan Head Screws
(#1)
Back of
Desktop
#10 x 3/4
Pan Head Screws
(#2)
Back of
Leg
5
Assembly (continued)
3. Attach the Leg Cross Member to both Legs using
two 1/4-20 x .590 Machine Screws (#3) and 1/4-20 Cap Nuts (#5).
Leg Cross
Member
1/4-20 x .590
Machine Screws
(#3)
1/4-20
Cap Nuts
(#4)
4. Attach the Stiffener to the rear Desktop pilot holes using
eight #10-16 x 3/4 Pan Head Screws (#2) as shown.
Stiffener
#10 x 3/4
Pan Head Screws
(#2)
6
Assembly (continued)
5. With the glides facing the inside,
attach both Keyboard Brackets
to the Desktop pilot holes using
six #10-16 x 3/4
Pan Head Screws
(#2) in each
as shown.
Left Hand
Keyboard
Bracket
#10 x 3/4
Pan Head Screws
(#2)
Right Hand
Keyboard
Bracket
6. Attach the Headphone Holder to one of the
Keyboard Brackets.
a. Attach to the Desktop pilot holes
using three #10-16 x 3/4
Pan Head Screws (#2).
b. Attach to the Keyboard Bracket
using one 1/4-20 x 1/2 Carriage Bolt (#6)
and 1/4-20 Lock Nut (#7).
The Headphone Holder is
typically attached to the
opposite side as the
CPU Holder.
Headphone
Holder
1/4-20 x 1/2
Carriage Bolt
(#6)
1/4-20
Lock Nut
(#7)
Nut Inserts
for attaching
Optional
CPU Holder
#10 x 3/4
Pan Head Screws
(#2)
7
Assembly (continued)
7. If attaching the optional Power Strip:
a. Fit the heads of two #10-32 x 3/8 Pan Head Screws (#8) into the slots in the Power Strip
and t the screws through the holes in the Stiffner as shown.
b. Attach a 10-32 Jam Lock Nut (#9) to each screw to secure the power strip to the Stiffener.
If not installing a Power Strip, skip ahead to the next step.
8. Attach the Wiring Clamps (#12) to the Stiffener with one #10-32 x 3/8 Pan Head Screw (#8)
and 10-32 Jam Lock Nut (#9).
Wiring
Clamp
#10-32 x 3/8
Pan Head
Screw
(#8)
10-32
Jam Lock
Nut
(#9)
Optional
Power Strip
#10-32 x 3/8
Pan Head Screws
(#8)
10-32
Jam Lock Nuts
(#9)
8
Assembly (continued)
Keyboard
Tray
9. Turn the Assembly over.
If attaching the optional CPU Holder:
a. Assemble the CPU Holder according to the manufacturer’s instructions.
b. Attach the CPU Holder
to the nut inserts in the
Desktop with four
1/4-20 x 5/8 Truss Head
Screws (#5) as shown.
If not installing a CPU Holder,
skip ahead to the next step.
10. Push the Grommet (#12) into the hole
in the Desktop.
11. Tip the Keyboard Tray into the
Keyboard Brackets and
push it closed.
Optional
CPU
Holder
1/4-20 x 5/8
Truss Head Screws
(#5)
Nut
Inserts
Grommet
(#12)
Table of contents
Other Wenger Desktop manuals
