Weider 2100 User manual

MEIDER2100

Model No. 831.159010

Serial No.

Write the serial number in the

space above for reference.

Serial Number Decal (under seat)

_" X F-. R C I SE.

EQUIPMENT

HELPLINE!

!-800-736-6879

SEARS, ROEBUCK AND CO.

HOFFMAN ESTATES, IL 60179

USER'S MANUAL

www.weiderfit ness.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ............................................................. 3

BEFORE YOU BEGIN ................................................................... 4

ASSEMBLY ........................................................................... 5

ADJUSTMENTS ...................................................................... 14

WEIGHT RESISTANCE CHART ........................................................... 16

CABLE DIAGRAM ..................................................................... 17

EXERCISE GUIDELINES ................................................................ 18

ORDERING REPLACEMENT PARTS ................................................ Back Cover

LIMITED WARRANTY ........................................................... BackCover

Note:A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before

beginningassembly.

WELDER is a registeredtrademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS

WARNING: To reduce the rlsk of serious injury, reed the following Important precau-

tions before using the weight system.

1, Read all Instructions in this manual and In

the accompanying literature before using the

weight system. Use the weight system only

as described in this manual.

11. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop Immediately and make

sure that the cables are on all of the pulleys.

2. It Is the responsibility of the owner to ensure 12. Always stand on thefoot plate when per-

that an users of the weight system are ade- formlng an exercise that could cause the

quately Informed of all precautions, weight system to tip.

3. The weight system Is Intended forhome use 13. Always disconnect the lat bar from the

Ing down.

7. Keep hands and feet eway;frommovlngparts:

our toll-free HELPLINE

Uon shown.

• Misuseofthisproduct

mayresultinserious

injury.

•Readuser'smanual

andfollowall warnings

andooeratinginstruc

tionsenortouse

•Donotallowchilaren

onorarounomacn_ne

•Replacelabelif

damaged,illegible,or

removeo.

Decal I

10. Never release the press arm, butterftyfarms,

leg lever, at bar, ()r handle whllewelgh;ts_are

raised, the weights will fall with great force. Decal 2

BEFORE YOU BEGIN

Thank you for selectingthe versatile WELDER®2100

weight system.The WELDER" 2100 offersaselection

of weightstationsdesigned todevelop every major

musclegroup ofthe body.Whether yourgoal isto tone

your body,builddramatic muscle size and strength,or

improveyourcardiovascularsystem,the WELDER®

2100 will helpyou to achieve the resultsyou want.

For your benefit, read this manual carefully before

using the weight system, ifyou have additional

questions,please call ourtoll-free HELPLINE at

1-800-736-6879, Monday throughSaturday,7a.m.

until7 p.m. Central Time (excludingholidays).To help

usassistyou, please note the productmodelnumber

and serial number beforecalling.The model numberis

831.159010. The serial numbercan befound on a

decal attached to the weightsystem (see the front

coverof this manual).

Before readingfurther,please review the drawing

belowand familiarizeyourselfwith the parts that are

labeled.

LSt Bar

High PulleyStation

PressArm/Butterfly

Front Upright

ASSEMBLED

DIMENSIONS:

Height: 74 in.

Width: 42 in.

Length: 60 in.

Warning Decal 2

(One on each side

of the front upright.)

Decal 1

Backrest

Seat Weight Carriage

Leg Lever Low Pulley Station

Foot Plate

ASSEMBLY

• As you assemble theweight system,make sure

all parts are orientedas shownin the drawings.

Before beginning assembly, carefully rend the

following Information and Instructions:

•Assemblyrequirestwo people.

•Place all parts in a cleared area and remove the

packing materials. Do not disposeof the packing

materials untilassembly iscompleted.

•"13ghtenall partsas you assemble them, unless

instructedto do otherwise.

•For help identifyingsmall parts, use the PART

The following tools (not Included) are required

for assembly:

•two adjustable wrenches

•one rubber mallet

•one standard screwdriver

• one Phillips screwdriver

•lubricant, such as grease or petroleum jelly,

and soapy water.

Assemblywillbe moreconvenientifyou have a

socketset, a set of open-endor closed-end

wrenches, or a set of ratchetwrenches.

Before beginning assembly, be sure that you

have rend and understand the Information In

the box above.

Presstwo 50mm x 75mm Inner Caps (29) into

the sides ofthe Foot Plate (74).

Orientthe Rear Base (3) with the indents around

the holeson the bottom.Attach the Front Base

(1) and the Rear Base tothe Center Base (2) with

two M10 x 70mm Bolts(58) and two M10 Nylon

Locknuts(71).

Insertsix M10 x 65mm Carriage Bolts(57) up

throughthe Frontand Rear Bases (1, 3).

Press the three Base Caps (28) onto the ends of

the Front Base (1), the Center Base (2), and the

Rear Base. Secure the Base Caps withthree M4

x 20mm Screws(77) and three M5 Washers (75).

Attachthe Foot Plate (74) to the Center Base (2)

withtwo M10 x 65mm Carriage Bolts(57) and

two M10 Nylon Locknuts(71).

58 Indents

58 29 74

_75

-71

57 57

3. Attach the Rear Upright (7) to the Rear Base (3)

with the two indicatedM10 x 65mm Carriage

Bolts(57) and two M10 Nylon Locknuts(71).

Press a 38mm Square InnerCap (41) intothe

tube on the Front Upright (6).

Attachthe Front Upright (6) to the FrontBase (1)

with thetwo indicatedM10 x 65mm Carriage

Bolts(57) and two M10 Nylon Locknuts(71).

Do not tighten the MIO Nylon Locknuts (71)

yet.

4. Press a50mm Square Inner Cap (22) intothe

Seat Upright (73). Attachthe Bumper (25) to the

Seat Uprightwith an M4 x 20mm Screw (77) and

an M5 Washer (75).

Attachthe Seat Upright(73) to the Front Base (1)

with the two indicatedM10 x 65mm Carriage

Bolts(57) and two M10 Nylon Locknuts(71). Do

not tighten the Nylon Locknute yet.

5. Make sure there is a Carriage Bushing(32) inside

the top of the Carriage Stop (31). Slide the

Carriage Stop onto the Rear Upright(7) and

attach itat the indicatedhole (see the insetdraw-

ing) withan M8 x 70mm Bolt(72) and an M8

Nylon Locknut (70).

Make sure there are two Carriage Bushing(32)

inside thetop and bottomof the Weight Carriage

(14). Presstwo 25mm Round Inner Caps (33)

intothe ends of the tube on the Weight Carriage.

Insertan M10 x 20mm Bolt(67) intothe bracket

on the Weight Carriage.

Slide the Weight Carriage (14) ontothe Rear

Upright (7). Press a 50mm Square Inner Cap (22)

ontothe top of the Rear Upright.

157

6. Pressa 50mm Square Inner Cap (22) intothe

end of the Top Frame (8).

Attachthe Top Frame (8) to the Front Upright(6)

withtwo M10 x 70mm Bolts(58), the 90mm

Space SupportPlate (21), and two M10 Nylon

Locknuts(71).

Attach the Top Frame (8) tothe Rear Upright(7)

with two M1Ox 70mm Bolts(58), the 70mm

Space Support Plate (56), and an M10 Nylon

Locknut(71).

0o not tighten the M10 Nylon Looknuts (71)

yet.

7. Attachthe Seat Frame (5) to the Front Upright(6)

withtwo M10 x 70ram Bolts(58), two M10

Washers (26), and two M10 Nylon Locknuts(71).

Attach the Seat Frame (5) to the Seat Upright

(73) with two M10 x 70ram Bolts (58), two M10

Washers (26), and two M10 Nylon Locknuts(71).

Tighten the M10 Nylon Locknuts (71) used In

steps 2-7.

8. Press a 50mm Square Inner Cap (22) intothe

ButterflyFrame (9).

Lubricatethe M10 x 75mm Bolt(60) with grease.

Attach the ButterflyFrame (9) to the Top Frame

(8) withthe Boltand an M10 Nylon Locknut(71).

Do not overtlghten the Locknut; the Butterlly

Frame must be able to pivot easily.

658

•0"i

22 ..-'_

9. 9

Press a 40mm x 50mm Inner Cap (23) intothe

indicatedend of the RightButterflyArm (11). Wet

the bottomend of theArm with soapy water. Slide

a Large Foam Pad (19) ontothe Arm.

Attach a Pivot Bracket (48) to the Right Butterfly

Arm (11) with an M10 x 50mm Bolt(62) and an

M10 Nylon Locknut(71). Do not overtlghten the

Looknut; the Pivot Bracket must be able to

pivot easily.

Slide aFoam Grip (76) ontothe Right Handle

(13). Attachthe Handle to the Right ButterflyArm

(11) withtwo M8 x 15ram Bolts(64).

Slide the Large Foam Pad (19) down sothat the

bottomof the Foam Pad iseven with the bottomof

the Arm.

Repeat this step with the Left Butterfly Arm (10).

10. Lubricatean M10 x 82mm Bolt(50) and both

sides of two PlasticWashers (55) with grease.

Attach the Right ButterflyArm (11) tothe Butterfly

Frame (9) withthe Bolt, the two PlasticWashers,

two ButterflyCaps (54), and an M10 Nylon

Locknut(71). Do not overtlghten the Locknut;

the Butterfly Arm must be able to pivot easily,

Be sure the indented sides of the Plastic

Washers fit over the welded bushing In the

Butterfly Arm.

Repeat this step with the Left Butterfly Arm

(10).

11. Press two 40mm x 50mm Inner Caps (23) into

the ends of the Leg Lever (4).

Lubricatean M10 x 65mm Bolt (59) with grease.

Attach the Leg Lever (4) to the Seat Upright(73)

with the Boltand an M1ONylon Locknut(71). Do

not overt_ghten the Locknut; the Leg Lever

must be able to pivot easily.

Welded Lubricate

Bushir x'_50

55_ """-

9"" i

Lubricate

4_Lubricate

23--

12. Locate the Butterfly Cable (46). Attach the

ButterflyCable to the indicatedPivotBracket (48)

with an M8 x 27mm Shoulder Bolt(63) and an M8

Nylon Locknut (70).

13. Wrap the ButterflyCable (46) arounda "V"-Pulley

(39). Attach the Pulley and a Long Cable Trap

(40) tothe bracket on the Front Upright(6) with

an M10 x 55mm Bolt (69) and an M10 Nylon

Locknut(71). Be sure the Cable Trap Is turned

to hold the Cable In the Groove of the Pulley.

14, Wrap the ButterflyCable (46) arounda 90mm

Pulley(38). Attach the Pulleytothe Double"U"-

Bracket (37) with an M10 x 47mm Bolt (61) and

an M10 Nylon Locknut(71).

15. Wrap the ButterflyCable (46) arounda "V"-Pulley

(39). Attach the Pulleyand a Long Cable Trap

(40) to the bracket on the Front Upright(6) with

an M10 x 55mm Bolt(69) and an M10 Nylon

Locknut(71). Be sure the Cable Trap Is turned

to hold the Cable In the Groove of the Pulley.

,,6

/71 39

4_/_/69

16. Attach the ButterflyCable (46) to the indicated

Pivot Bracket (48) with an M8 x 27mm Shoulder

Bolt (63) and an M8 Nylon Locknut (70).

17. Locate the High Cable (45). Routethe eyelet

end of the Cable up throughthe Top Frame (8)

and arounda 90mm Pulley(38). Attach the Pulley

inside the Top Frame with an M1Ox 7Omm Bolt

(58), two M10 Washers (26), two 13mm Spacers

(34), and an M1O Nylon Locknut(71).

18. Wrap the High Cable (45) around a 90mm Pulley

(38). Attachthe Pulley insidethe Top Frame (8)

withan M10 x 70mm Bolt (58), two M1OWashers

(26), two 13mm Spacers (34), and an M1ONylon

Locknut (71).

19. Wrap the High Cable (45) arounda 90mm Pulley

(38). Attach the Pulleyand aCable Trap (44) to

the second set of holesfrom the top ofthe two

PulleyPlates (36) with an M10 x 47mm Bolt(61)

and an M10 Nylon Locknut(71). Be sure the

Cable Trap Is turned to hold the Cable In the

Groove of the Pulley.

71 34

6.,61

36 _

This manual suits for next models

Table of contents

Other Weider Fitness Equipment manuals

Weider

Weider WEBE11921 User manual

Weider

Weider 831.14622.0 User manual

Weider

Weider D480 User manual

Weider

Weider X4s Power Guide User manual

Weider

Weider 130 TC User manual

Weider

Weider 195 Tc Bench User manual

Weider

Weider Pro 9545 User manual

Weider

Weider 133 User manual

Weider

Weider WECCBE72010 User manual

Weider

Weider CJXT3 User manual

Weider

Weider 220 User manual

Weider

Weider Pro 9648 User manual

Weider

Weider WEEVSY62000 User manual

Weider

Weider CROSS BOW ADVANTAGE WESY59830 User manual

Weider

Weider Crossbow ADVANTAGE WESY59831 User manual

Weider

Weider Pro Pt 800 Bench Setup guide

Weider

Weider Pro 9655 User manual

Weider

Weider Pro 9515 User manual

Weider

Weider 8925 User manual

Weider

Weider 2172 Vector 7 User manual

Weider

Weider 8510 User manual

Weider

Weider Pro 120 WEEVBE70200 User manual

Weider

Weider 2990 I User guide

Weider

Weider 8510 User manual

Popular Fitness Equipment manuals by other brands

NSD

NSD PB-188P user manual

Performance

Performance HyperVibe User instructions

Scalamobil

Scalamobil S27 Operator's manual

Precor

Precor Experience Series Service manual

FYTTER

FYTTER RedMIUM BENCH BE-T6R manual

Taurus

Taurus TF-RK1312 Assembly and operating instructions

Nustep

Nustep T5 Assembly instructions

Precor

Precor CW-507 Assembly guide

Movement

Movement BICEPS Idea owner's manual

Kegel8

Kegel8 V For Men user guide

Skandika

Skandika Styrke II instruction manual

BLK BOX

BLK BOX 21-0122-0B Owner's manual & quick start guide

Stamina

Stamina aeropilates premier 299 owner's manual

SPORTSTECH

SPORTSTECH PBX300 quick start guide

ParaBody

ParaBody Serious Steel 877102 Assembly guide

Weslo

Weslo Gym 650 Gebruikershandleiding

Rebel

Rebel ACTIVE RBA-1011 user manual

4iiii

4iiii FLiiiight owner's manual