WE-EF RMC320 LED User manual

WE-EF LEUCHTEN

Installation and Maintenance

Instructions

Street and Area Lighting Luminaire

RMC320 LED

Do not open during installation

This product is factory-sealed.

Refer to the instructions contained in this

document for details.

Surge Protection

This product features built-in surge protection circuitry in compliance with

applicable standards.

For comprehensive protection of a luminaire installation against lightning and

electrical surges, it is essential to cover mains supply and data input lines at

the distribution board level, by using respective primary (Type 1) and secondary

(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.

Warning

Ensure that all required surge protection measures are in place and activated

prior to luminaire installation. Also, disconnect luminaires before operating

high-power devices such as, for example, electrical arc welders.

IP66, IK08, Class I, ta = 40°C

Street and Area Lighting Luminaire

RMC320

650

325

Light Source

LED

Maintenance

Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.

Do not use high-pressure cleaners.

In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out

by a suitably qualiƂed and trained professional.

Warning: Do not open luminaire while mains supply is switched on.

Single bracket Double bracket

Wall bracket Short bracket

Mounting Accessories

Wall bracket

RM1-W for RMC320 105-9846

Short bracket – Galvanised steel. For lateral mounting on a pole.

RM1-S for RMC320 105-9845

Single bracket

RM1-76* for RMC320 105-9847 AMW-C Wooden pole

RM1-76** for RMC320 105-9849 AMF-C Steel pole

Double bracket

RM2-76* for RMC320 105-9848 AMW-C Wooden pole

RM2-76** for RMC320 105-9850 AMF-C Steel pole

Installation

The product must be installed and maintained by a

suitably qualiƂed professional in compliance with latest

building/construction and/or electrical regulations and

relevant legislation.

Warning: Switch off mains electrical supply prior to

installing and connecting the luminaire.

Notice: If the luminaire is modiƂed by anybody other

than the original manufacturer, then the warranty will

no longer be valid and shall become the full respon-

sibility of the modifying person/organisation. Claims

based on defects attributable to improper installation

and/or application, and the consequences thereof, are

excluded.

Installation Procedure

Installation – Pole

1) Switch off mains electrical supply.

2) Check that rating shown on luminaire label conforms

with mains electrical supply.

3) Feed mains cable Cinto column D, while setting

bracket/luminaire assembly in position. Tighten

screws E.

4) Trim mains cable Cto the desired length and con-

nect the leads to their respective terminals at the

base of the pole (L = Phase, N = Neutral,

= Earthing)

Installation – Wall bracket

1) Switch off mains electrical supply.

2) Check that rating shown on luminaire label conforms

with mains electrical supply.

3) Access mounting ƃange Jby loosening screws K.

4) Determine positions for Ƃxing screws L. Ensure

arrow mark Ron ƃange Jaims upwards. Drill rele-

vant holes and insert wall plugs M.

Warning: Ensure not to damage any electric cable,

water pipe or other devices while drilling holes.

5) Feed mains supply cable N(and second cable for

through wiring, if required) through packing ring(s)

O, while setting and securing mounting ƃange J

in position. The pre-installed packing ring(s) Oare

suitable for cable diameters 7 to 9.5 mm. For larger

cable diameters (9.5 to 12 mm) use the auxiliary

packing ring(s). Tighten pressure screws S.

To secure mounting ƃange J, insert screws L, and

tighten.

6) Connect mains supply cable Nto the respective

terminals in terminal connectors P(L = Phase,

N = Neutral, = Earthing)

7) Position luminaire/wall bracket Qby attaching

to mounting ƃange Jand secure in position by

tightening screws K.

Installation to a Pole

Installation – Wall bracket

Individual wiring Through wiring

ON/OFF or WE-EF Control Advanced

www.we-ef.com

WE-EF LEUCHTEN

Germany

Tel +49 5194 909 0

Fax +49 5194 909 299

info.germany@we-ef.com

WE-EF LUMIERE

France

Tel +33 4 74 99 14 44

Fax +33 4 74 99 14 40

info.france@we-ef.com

WE-EF HELVETICA

Switzerland

Tel +41 22 752 49 94

Fax +41 22 752 49 74

info.switzerland@we-ef.com

WE-EF LIGHTING

United Kingdom

Tel +44 844 880 5346

Fax +44 844 880 5347

info.uk@we-ef.com

WE-EF LIGHTING

Thailand

Tel +66 2 738 9610

Fax +66 2 175 2174

info.asiapaciƂc@we-ef.com

WE-EF LIGHTING

Australia

Tel +61 3 8587 0444

Fax +61 3 8587 0499

info.australia@we-ef.com

WE-EF LIGHTING

United States of America

Tel +1 724 742 0030

Fax +1 724 742 0035

info.usa@we-ef.com

Technical speciƂcations are

subject to change.

Other manuals for RMC320 LED

Table of contents

Other WE-EF Lantern manuals

Popular Lantern manuals by other brands

KYOWA

KYOWA KW-9114 instruction manual

Stahl

Stahl ECOLUX 6610 Series operating instructions

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Operator's manual

PRG

PRG VARI LITE VL5 Service manual

Raytec

Raytec VARIO2 series installation guide

ENSA

ENSA LEDBT18WS2 installation instructions

LUG

LUG OFFICE LB LED N/T Installation instruction

GE Wallighter 250 instructions

Draper

Draper RLEDL19/B instructions

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Assembly & fitting instructions

Panasonic

Panasonic EY3741B57 operating instructions

Clas Ohlson

Clas Ohlson LCC8T instruction manual

Coolon

Coolon WDN-140 manual

Holiday Travel

Holiday Travel 834873 manual

BEGA

BEGA 84 036 Instructions for use

BEGA

BEGA 33 596 Instructions for use

Dale Tiffany

Dale Tiffany GT701162 Assembly instructions

Wagan

Wagan Brite Nite Pop-Up USB Lantern user manual