WE-EF ETV100 Series User manual
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETV100 LED
1
Inground Luminaire
ETV100
IP67, IK08. Class I. ta = 25°C
L
50
48
Product Dimensions:
ETV100 series L
ETV120 627
ETV130/ETV130-CC 927
ETV140/ETV140-CC 1227
Mounting Accessories:
Installation blockout Type I Type II
B = 160 mm B = 130 mm A
for 1 x ETV120 186-0306 186-0281 675
for 2 x ETV120 186-0307 186-0282 1304
for 3 x ETV120 186-0308 186-0283 1933
for 4 x ETV120 186-0309 186-0284 2562
for 1 x ETV130/ETV130-CC 186-0310 186-0285 975
for 2 x ETV130/ETV130-CC 186-0311 186-0286 1905
for 3 x ETV130/ETV130-CC 186-0312 186-0287 2833
for 4 x ETV130/ETV130-CC 186-0313 186-0288 3762
for 1 x ETV140/ETV140-CC 186-0314 186-0289 1275
for 2 x ETV140/ETV140-CC 186-0315 186-0290 2504
for 3 x ETV140/ETV140-CC 186-0316 186-0291 3733
for 4 x ETV140/ETV140-CC 186-0317 186-0292 4962
B
2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.
3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
The installation on site must comply with local and/or
national health and safety regulations.
4
Blockout Installation Procedure
(during earth or masonry work)
1) Remove installation cover Aout of installation
blockout B.
4) Place mains cable C(and second cable Efor
through wiring) at bottom area of blockout,
then return installation cover A.
2) Ensure that proper drainage is provided.
Holes Jare for drainage.
3) Feed mains supply cable C(and second
cable Efor through wiring) through holes
inside blockout.
5) Blockout needs to get placed on an even, stable
DUHD7RSHGJHQHHGVWREHƃXVKZLWKVXUIDFH
Attention: ,IƃRRUZLOOEHWLOHGRUSDYHGDIWHUZDUGV
leave an appropriate gap. In case luminaire
gets installed at a later time, blockout must get
covered by installation cover A, to make sure no
concrete or dirt may enter luminaire. Installation
cover ensures that blockout does not get damaged
during masonry works and needs to remain inside
blockout until installation of luminaire.
5
1) Switch off mains electrical supply.
4) Remove installation cover Afrom blockout B.3) Luminaire is pre-wired and LED included.
Opening the luminaire is not necessary.
Luminaire Installation Procedure
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
ETV120 220-240V/50-60 Hz
186-XXXX SOE XXXXXXX
02/19 IP67
6
5) Take sealable junction box Gfrom its bag and open it.
Warning: Be careful to not get dirt inside the gel connector when opened and connecting mains cable.
Connect leads of luminaire cable Dand mains supply cable C (and second cable Efor through wiring)
to respective terminals in terminal connector F. Mains cables Cand Emust not cross to ensure sealable
junction box Gcan be properly closed.
b) DALI (L = Phase, N = Neutral, = Earthing,
DA/DA = DALI control line, DA/DA = DALI
control line)
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
ø 7.5-16 mm for ON/OFF ø 6.5-12 mm for DALI
c) DMX: refer to separate TO9256W wiring instruction for hybrid DMX cable.
Attention:
a) To properly terminate and seal cables with sealable junction box, refer to information
packed with each sealable junction box G.
b) Cable sheaths must be contained within gel.
7
7) Install spacers I. To remove luminaire unfasten screws K out of
spacers I until you can grab their heads. Insert
lever Lbetween head of screws and spacers.
Lift spacers in an upwards direction.
6) Place sealable junction box Gand luminaire H
inside blockout. Make sure no cable is squeezed.
we-ef
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel +49 5194 909 0
Fax +49 5194 909 299
info.germany@we-ef.com
WE-EF LUMIERE
France
Tel +33 4 74 99 14 44
Fax +33 4 74 99 14 40
info.france@we-ef.com
WE-EF HELVETICA
Switzerland
Tel +41 22 752 49 94
Fax +41 22 752 49 74
info.switzerland@we-ef.com
WE-EF LIGHTING
United Kingdom
Tel +44 844 880 5346
Fax +44 844 880 5347
info.uk@we-ef.com
WE-EF LIGHTING
Thailand
Tel +66 2 738 9610
Fax +66 2 175 2174
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel +61 3 8587 0444
Fax +61 3 8587 0499
info.australia@we-ef.com
WE-EF LIGHTING
United States of America
Tel +1 724 742 0030
Fax +1 724 742 0035
info.usa@we-ef.com
TO9258W0719 © WE-EF 2019
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Wiring instruction for hybrid DMX cable
Other manuals for ETV100 Series
1
This manual suits for next models
5
Table of contents
Other WE-EF Lantern manuals
WE-EF
WE-EF QLS400 Series User manual
WE-EF
WE-EF XLO200 LED Series User manual
WE-EF
WE-EF ZFT400 Series User manual
WE-EF
WE-EF VFL500 LED Series User manual
WE-EF
WE-EF ETC330-GB LED User manual
WE-EF
WE-EF RBL640 User manual
WE-EF
WE-EF ETC330-GB LED User manual
WE-EF
WE-EF ASP500 LED User manual
WE-EF
WE-EF PFL230 LED User manual
WE-EF
WE-EF VFL530-SE LED User manual
WE-EF
WE-EF ETC130-FS LED User manual
WE-EF
WE-EF ETC320-GBLED User manual
WE-EF
WE-EF RFL530-SE LED User manual
WE-EF
WE-EF FLC122 LED User manual
WE-EF
WE-EF ETC339-FS LED User manual
WE-EF
WE-EF ETC100-GB LED Series Technical specifications
WE-EF
WE-EF FLC122 LED User manual
WE-EF
WE-EF RMC320 LED User manual
WE-EF
WE-EF PFL240 LED User manual
WE-EF
WE-EF QLS410 LED User manual
